Manual

ManualsBrandsArmscor ManualsFirearmsMAK22

ARMSCOR

MANUAL FOR

MODEL AK 22

SEMI AUTOMATIC

WARNING

READ THE ISTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL

CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN

POORLY VENTILATED AREAS, CLEANING FIREARMS OR HANDLING

AMMUNITION MAY RESULT IN EXPOSURE TO LEAD AND OTHER

SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH

DEFECTS, REPRODUCTIVE HARM AND OTHER SERIOUS PHYSICAL INJURY.

HAVE ADEQUATE VENTILATION AT ALL TIMES. WASH HANDS YOUR

THOROUGHLY AFTER EXPOSURE.

OPERATING INSTRUCTIONS

Before proceeding to use rifle, a word of caution is in order. This rifle is safe to handle

and use as we can make it. The safety of this gun is correctly design, fitted & tested.

Always point your firearm to a safe target. Careless handling can cause accident. Never

load a gun until you are ready to use it. Always keep gun pointed to a safe direction and

never to anyone or anything not intended as a target. Think of yourself and your rifle as

part of a system whose safe operating depends on you. Your rifle can’t think, you can.

This rifle is shipped from the factory fully assembled and ready for use once you’re

removed the grease and excess gun oil from the bore and rifle’s action.

1. TO LOAD MAGAZINE

Hold magazine box firmly with one hand, and with the other hand, place cartridge

on top of magazine follower with the cartridge head just after the magazine

retaining lips. Press down the cartridge and then push it rearward until it is

Summary of content (11 pages)

PAGE 1
ARMSCOR MANUAL FOR MODEL AK 22 SEMI AUTOMATIC WARNING READ THE ISTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM. DISCHARGING FIREARMS IN POORLY VENTILATED AREAS, CLEANING FIREARMS OR HANDLING AMMUNITION MAY RESULT IN EXPOSURE TO LEAD AND OTHER SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS, REPRODUCTIVE HARM AND OTHER SERIOUS PHYSICAL INJURY. HAVE ADEQUATE VENTILATION AT ALL TIMES. WASH HANDS YOUR THOROUGHLY AFTER EXPOSURE.
PAGE 2
secured in place. Repeat the process with the succeeding loads until magazine is full. The magazine can hold maximum of fifteen (15) rounds 2. TO ATTACH MAGAZINE Insert magazine into the receiver cover bottom-side opening. Push it in until magazine catch button lock in-place in the magazine slot. 3. TO DETACH MAGAZINE Fully press magazine release and simultaneously pull magazine away from the rifle. 4. TO OPERATE THE SAFETY Safety lever is at the right side of the receive cover.
PAGE 3
rearward (bolt open) and let it snap forward freely. This must be done repeatedly until the chamber is free of any cartridges. CAUTION: You must examine visually the chamber breech area to be sure that new cartridges remain. Visual check may be accomplished by placing bolt into bolt-open position. Placing the bolt in open position is done by pulling the bolt handle rearward to a distance just above the location of safety lever square notch.
PAGE 4
b) VERTICAL CORRECTION. To raise the center of impact, move the rear sight elevator ring forward, in one position at a time. To lower the center of impact, move the rear sight elevator ring rearward. 10. CLEANING THE RIFLE WARNING: Before cleaning your rifle, be certain it is completely unloaded. Clear the action several times to be sure no cartridges remain in the chamber. With normal use it is not necessary to clean the bore of your rifle.
PAGE 5
Step 8) With the use of extra long and heavy-duty screw driver, swing out the butt plate and insert the screw driver into the hole of the butt stock and loosen the stock bolt (Part #3046) which is inside the butt. Step 9) Now you can separate the butt stock from the rifle. Step10) Loosen out the three (3) screws in the receiver cover right side. Then separate the left side receiver cover the rifle assembly together with right side receiver cover.
PAGE 6
CAUTION should be exercised in re-attaching the receiver cap. You have to compress the springs gently and firmly to avoid bucking or kinking of springs, let the threads of receiver cap touches the thread of the receiver and rotate the cap clock-wise to tighten. Step19) To reassembly, follow the steps stated above in the reverse order. SPECIFICATIONS : Model : AK. 22 SEMI-AUTO RIFLE Caliber : .
PAGE 7
Front Sight Stud Lock Screw 1608 Front Sight Stud Set Screw 1605 Gas Tube (Dummy) AK003 Gas Tube Front Retainer AK004 Gas Tube Front Retainer Set Screw 1605 Rear Sight Base AK005 Rear Sight Block AK006 Rear Sight Block Screw AK007 Rear Sight Stem Bar AK008 Rear Sight Pivot Pin AK009 Rear Sight Elevating Spring 15009 Rear Sight Base Retainer Screw 1611 Rear Sight Elevator Ring AK010 Rear Sight Locator Bearing 1638 Rear Sight Locator Bearing Spring 15035 Receiver 1616 Receiver
PAGE 8
B-BOLT ASSEMBLY Bolt 1619 Bolt Handle AK016 Extractor 1624 Extractor Plunger 1625 Extractor Spring 1626 Firing Pin 1627 Firing Pin Spring 1628 Firing Pin Spring Guide Head 2 Stem 1629 Firing Pin Spring Guide Head 2 Stem Insert 1629A Recoil Spring 1630 Recoil Spring Guide Sleeve 1631 Recoil Spring Retainer Sleeve 1632 C-TRIGGER HOUSING ASSEMBLY Magazine Catch 1633 Magazine Catch Button 1634 Magazine Catch Pivot Pin 1635 Magazine Catch Stop Pin 1635A Magazine Catch Spring 1635
PAGE 9
Rebound Lever Pivot Pin 1652 Rebound Lever Safety Pin 1653 Rebound Lever Spring 1654 Rebound Lever Spring Bearing 1655 Trigger Housing 1656 Trigger Housing Front Hold Down Screw 1657 Trigger Housing Front Down Screw Washer 1657A Trigger Housing Rear Hold Down Screw 1658 Trigger Housing Rear Hold Down Screw Washer 1658A D- MAGAZINE BOX ASSEMBLY ` Magazine Box 1659 Magazine Box Inner Strip 1660 Magazine Spring 1661 Magazine Spring Follower 1662 Magazine Spring Retainer 1663 Magaz
PAGE 10
Butt Stock Bolt Nut AK021B Butt Stock Bolt Nut Lock Washer AK021C Stock Bolt Washer 3048 Swivel (1pcs.) Ring Plates 1673 Swivel Ring (2pcs.) 1674 Swivel Ring Plate Screw (2pcs.
PAGE 11