User's Guide
Table Of Contents
- Disclaimers
- Table of Contents
- CHAPTER 1 Introduction
- CHAPTER 2 Basic Mode Setup
- CHAPTER 3 Expert Mode
- Overview of Major Capabilities
- Wide Area Network Termination
- PPPoE/PPPoA (Point-to-Point Protocol over Ethernet/ATM)
- Instant-On PPP
- Simplified Local Area Network Setup
- DHCP (Dynamic Host Configuration Protocol) Server
- DNS Proxy
- Management
- Embedded Web Server
- Diagnostics
- Security
- Remote Access Control
- Password Protection
- Network Address Translation (NAT)
- Cayman Advanced Features for NAT
- Internal Servers
- Pinholes
- Default Server
- Combination NAT Bypass Configuration
- VPN IPSec Pass Through
- Access the Web Interface
- Toolbar
- Navigating the Web Interface
- Restart
- Help
- Configure
- Button: Configure
- Quickstart
- How to Use the Quickstart Page
- Link: Configure -> Quickstart
- Setup Your Gateway using a PPP Connection
- LAN
- Link: Configure -> LAN
- WAN
- Link: Configure -> WAN
- Advanced
- Link: Advanced
- Link: IP Static Routes
- Link: IP Static ARP
- Link: Pinholes
- Configure Specific Pinholes
- Planning for Your Pinholes
- Example: A LAN Requiring Three Pinholes
- Pinhole Configuration Procedure
- Link: IPMaps
- Configure the IPMaps Feature
- What are IPMaps and how are they used?
- What types of servers are supported by IPMaps?
- Can I use IPMaps with my PPPoE or PPPoA connection?
- Will IPMaps allow IP addresses from different subnets to be assigned to my Gateway?
- Link: Default Server
- Configure a Default Server
- Typical Network Diagram
- NAT Combination Application
- IP-Passthrough
- A restriction
- Link: DNS
- Link: DHCP Server
- Link: SNMP
- Link: Advanced -> Ethernet Bridge
- Configuring for Bridge Mode
- Link: Stateful Inspection
- Exposed Addresses
- Stateful Inspection Options
- Link: System
- Link: Syslog Parameters
- Link: Internal Servers
- Link: Software Hosting
- Rename a User(PC)
- Link: Clear Options
- Security
- Button: Security
- Link: Passwords
- Create and Change Passwords
- Link: Firewall
- BreakWater Basic Firewall
- Link: IPSec
- Link: Security Log
- Install
- Button: Install
- Link: Install Software
- Updating Your Gateway’s CaymanOS Version
- Task 1: Required Files
- Task 2: CaymanOS Image File
- Link: Install Keys
- Use Cayman Software Feature Keys
- Overview of Major Capabilities
- CHAPTER 4 Basic Troubleshooting
- CHAPTER 5 Advanced Troubleshooting
- CHAPTER 6 Command Line Interface
- Overview
- Starting and Ending a CLI Session
- Using the CLI Help Facility
- About SHELL Commands
- SHELL Commands
- About CONFIG Commands
- CONFIG Commands
- DSL Commands
- ATM Settings
- Bridging Settings
- DHCP Settings
- DMT Settings
- Domain Name System Settings
- IP Settings
- IP-over-PPP Settings
- Static ARP Settings
- IPMaps Settings
- Network Address Translation (NAT) Default Settings
- Network Address Translation (NAT) Pinhole Settings
- PPPoE Settings
- Configuring Basic PPP Settings
- Configuring Port Authentication
- Command Line Interface Preference Settings
- Port Renumbering Settings
- Security Settings
- SNMP Settings
- System Settings
- Syslog
- Wireless Settings (supported models)
- CHAPTER 7 Glossary
- CHAPTER 8 Technical Specifications and Safety Information
- Index
187
CONFIG Commands
set ip ip-ppp [vccn] rip-send
{ off | v1 | v2 | v1-compat | v2-MD5 }
Specifies whether the Cayman Gateway unit should use Routing
Information Protocol (RIP) broadcasts to advertise its routing
tables to routers on the other side of the PPP link. An extension
of the original Routing Information Protocol (RIP-1), RIP Version
2 (RIP-2) expands the amount of useful information in the pack-
ets. While RIP-1 and RIP-2 share the same basic algorithms,
RIP-2 supports several new features. For example, inclusion of
subnet masks in RIP packets and implementation of multicast-
ing instead of broadcasting. This last feature reduces the load
on hosts which do not support routing protocols. RIP-2 with
MD5 authentication is an extension of RIP-2 that increases
security by requiring an authentication key when routes are
advertised.
This command is only available when address mapping for the
specified virtual circuit is turned “off”.
set ip ip-ppp [vccn] rip-receive
{ off | v1 | v2 | v1-compat | v2-MD5 }
Specifies whether the Cayman Gateway should use Routing
Information Protocol (RIP) broadcasts to update its routing
tables with information received from other routers on the other
side of the PPP link.
This command is only available when address mapping for the
specified virtual circuit is turned “off”.
Static ARP Settings. Your Cayman Gateway maintains a
dynamic Address Resolution Protocol (ARP) table to map IP
addresses to Ethernet (MAC) addresses. Your Cayman Gateway
populates this ARP table dynamically, by retrieving IP address/