User's Manual

B. Scanning for Wi-Fi networks
B1. If your Wi-Fi access point does not
have a WPS button you should rst select
the “Scan” option to select your network
from a list of available networks.
B2. Select your network from the list by
moving up or down with the arrow keys
on your remote control. If your network is
not listed refer to section C. Press OK to
select your network.
B3. Press OK to launch the on-screen
keyboard. Use the arrow keys on the re-
mote control to select the correct letters
and numbers on the keyboard to enter
the Network Key (case sensitive). Press
OK to enter the selected character in the
input eld on the screen. “Backspace” is
used to erase errors. Use the arrow down
key to highlight “Done” at the bottom of
the screen when you have entered the
entire key, press OK. Highlight “Done”
again and press OK.
The conguration is tested and when the
screen shows the OK message your Wi-Fi
1 Connect to the TV set
Connect an HDMI cable between the
set-top box and the HDMI connector on
the TV set. This is the preferred method
and no other video/audio connection is
needed when HDMI is used. Note that
the analog video output is disabled when
HDMI is connected.
To display the picture from the set-top
box, the TV set must be switched to the
correct external input. This is either done
automatically or manually, using a button
on the TV remote control. See your TV
user’s guide for instructions.
2 Connect to power
Connect the power supply to the DC jack
on the set-top box and to a power outlet.
NOTE:
Do not use any power supply other
than the one supplied with the prod-
uct. Doing so may cause re or seri-
ously damage the set-top box.
4 Connect to your Wi-Fi
broadband
The recommended Wi-Fi setup method
is to use WPS. Read through all steps in
section A before you start. If your Wi-Fi
access point does not have a WPS but-
ton or WPS setup does not work, refer to
sections B or C. If the Wi-Fi network is out
of reach or unsuitable for video distribu-
tion, refer to INSTALLATION OPTIONS -
Connect to broadband via Ethernet.
A. Automatic setup using WPS
A1. When the Wi-Fi conguration setup
screen is displayed, select “WPS” using the
arrow keys on your remote control and
press OK to start the setup.
A2. You now have 2 minutes to press the
WPS button on your Wi-Fi access point.
Once you have pressed the WPS button
on your access point (within 2 minutes)
the conguration is tested and when the
screen shows the OK message your Wi-Fi
connection is established. Press OK on
your remote control to exit the setup.
If the WPS setup times out you will have
to retry until you see the OK message.
3 Prepare the remote
control
Insert the batteries in the remote control.
The remote control will initiate automatic
pairing with the set-top box when batter-
ies are inserted or on any key press.
NOTE:
You can return to the start screen by
pressing BACK ( the symbol is usually
shown as ) on your remote control.
connection is established. Press OK on
your remote control to exit the setup. If
you have entered the wrong key an error
message displays and you will have to
repeat this step.
C. Manual Wi-Fi setup
If your network is not shown in the list
you will need to manually enter both the
network name (SSID) and the key for that
network in order to connect your set-top
box.
C1. Press BACK ( the symbol is usually
shown as ) on your remote control to
return to the main screen. Select “Manual”
and press OK.
C2. Press OK to launch the on-screen
keyboard. Enter the network SSID and
Network Key using the on screen key-
board with the arrow keys on your remote
control. Please note that both the SSID
and Key are case sensitive. Press OK to
enter the selected character in the input
eld on the screen. “Backspace” is used
to erase errors. Use the arrow down key
to highlight “Done” at the bottom of the
screen when you have entered the entire
SSID and Network Key, press OK. Highlight
“Done” again and press OK.
The conguration is tested and when the
screen shows the OK message your Wi-Fi
connection is established. Press OK on
your remote control to exit the setup. If
you have entered the wrong SSID or key
an error message will show and you will
have to repeat the relevant step.
Connect video/audio with HDMI
through a home theater system or
HiFi equipment
Choose from below the option that best
ts your system conguration.
1. Digital audio equipment with HDMI
input: Connect the HDMI cable from the
set-top box to the home theater receiver,
and the home theater receiver HDMI
output to the TV set.
2. Digital audio equipment without HDMI
input: Connect the HDMI cable from the
set-top box to the TV set and an optical
Mini Toslink to Toslink cable from the set-
top box A/V output to the home theater
receiver.
Note: you may have to change your set-
tings for the TV set to ensure the digital
output is properly transmitted from the
TV set.
3. Analog audio equipment: Connect an
HDMI cable from the set-top box to the
TV set and a 3.5 mm to 3xRCA audio/
video cable in one end to the A/V connec-
tor of the set-top box and the other end
with 2xRCA to your audio equipment.
Connect video/audio to the TV set
without HDMI
If your TV does not have HDMI you can
connect a 3.5 mm to 3xRCA audio/video
cable from the A/V jack on the set-top
box to the video and R+L audio connec-
tors on the TV set. (Connectors are nor-
mally color coded: White = Left audio,
Red = Right audio, Yellow = Video.)
Connect to broadband via Ethernet
If you do not have a Wi-Fi network in your
home or if the Wi-Fi network is out of
reach or unsuitable for video distribution,
connect an Ethernet cable between the
set-top box and the router/modem or the
Ethernet wall connector as indicated by
your broadband operator. Once connect-
ed, remove and reinsert the power cable
to restart the set-top box.
INSTALLATION OPTIONS
1
2
TV
NOTE:
The set of cables and other accesso-
ries supplied by your service provider
together with this product may vary.
NOTE: Re-pairing the set-top box
with the remote control
This product package may include a
radio frequency remote control that
will be automatically paired with the
set-top box during the initial setup. If
you need to pair again, for instance
to replace the original remote control
with a new one, follow these steps:
1. Unplug the power cable.
2. Press and hold the standby but-
ton on the top cover and reinsert the
power cable.
3. Hold the standby button pressed
until the status indicator grid stops
ashing with amber light and turns
solid red.
4. Reset the remote control by press-
ing the ON/OFF and BACK keys
simultaneously for more than 3 sec-
onds. Once you have released the ON/
OFF and BACK keys press any key to
complete the pairing.