SEWRNG MACHINE CABINET OWNER'S Model Number MANUAL 272.98300.491 272.98301.491 Oak White 272.98302.49_ Cherry ASSEMBLY PARTS LIST IMPORTANT: Read instructions before assembling.
(20) (2) #8xl/2" Hardware Included Panhead Screws #6x5/8" Panhead Screws (6) #5x5/8" Flathead (25) (1) Right Wing (1) Left Wing _l Cams_ _j-_Screws _ _ _ (1) 2 pc, Knob (8) 5ram Hex Bolt Rubber Tab ! 3-Small 1-Large (2) Mounting Bolts (2) Wing Nuts ('r(/("f (2) Bronze Strike Washers (4) (2) Drawer Backs _ Allen Key Zinc Flat Washers "_ (5) Caster Clips (5) Caster Insert (8) (1) Strike Plate @ (2) Round Magnet (4) Connecting White Plastic 98301 only Drawer Sides _o
UnderstandingHowthe "ARR0W-LOC" CamFastenerWorks. ARROW TOWARDS HOLEIN EDGE 1. Position bolt in pre-drilled hole and 2. Press cam into pre-drilled hole until turn until tight, flush with surface, 4. To lock, rotate cam 3. Insert bolt through pre-drilled hole in until tight, using allen key provided. edge of panel. Cabinet Assembly Step 1.
CabinetAssemblyContinued: Step2• InstallCams(25total) into the holesprovidedin the cabinetparts shown below,pushinga caminto eachhole untilflush with the surface•Thearrowon the Camsshould be turned(using a regularscrewdriveror Allen KeyProvided)to facethe hole in eachedgewherethe Connecting Boltswill enter• Step2A•Weare providing(1)whiteplastic hookto be used,to store your custom fit sewingheadinsert, (Sears#9801) to be mounted on the inside left side panel in Hole (A) or (B).
Step 3. Attach the Magnet to the Partition by using (2) #6x5/8" Screws. Be sure to keep the magnet Strikes (metal) lacing towards the front edge ot the Partition (as shown in FiG. 2.) (_ /_] (2) #6x5/8" Screws /uo ! Partition (viewed from left) Step 4, Next, attach the plastic Drawer Runners by using (32) #6x1" Flathead Screws (as shown in FIG. 4). DO NOT OVER TIGHTEN. 6x1" Flathead Screws FIG. 4 I ® @ • / i I t .) Drawer Runners / ( • C • • ) • ) ( • ( • • • ,,• • • ) .
Step 5. Attach the Left and Right Wings to the Platform using (4) #8xl/2" Panhead Screws (as shown in FIG. 5). The long flanges facing outward and toward edge of Platform. FIG. 5 #8x1/2" Panhead Screws o o o 0 Platform Step 6. Attach the Wings (with Platform) to the Carriage of the Lift Mechanism by laying the Back (with Lift attached) in a flat position and aligning the top and bottom holes in Wing flanges with the holes in the Lift Carriage.
Step 7. Attach the (4) plastic Trays to the Door by inserting the (16) #8xl/2" Panhead Screws into the Door. The (3) smaller trays are mounted in the three top rows of predrilled holes, with larger tray mounted in bottom row. Attach Magnet Strike Plate with (1) #5xl/2" Flathead Screw. Attach (2) door hinges to Door with (6) #5xl/2" Screws (as shown in FIGS. 7 AND 7A). Long end attaches to door. #8x1/2" Panhead Screw #5x1/2" Flathead Screw Door Step 8.
Step 9. Place or tap Caster Clips, Inserts, (1) Locking Caster, and (1) Non-Locking Caster into Left Side (as shown in FIG. 9 below). Attach the back to Left Side by guiding Back onto Connecting Bolts in Left Side (as shown in FIG. 9), turn Cams to the Locked Position. Attach the Shelf and Front by guiding each piece onto the appropriate Bolts in the side, and turn the Cams to the Locked Position. FIG. 9 Taped Edge-_ Front 1 | o . @ Back @ ® 1 I ! II } FIG, 9A I I il I 'i CasterC,p .
Step 10. Place or tap Caster Clip, Insert and Non-Locking Caster into the Partition (as shown in Fig. 10. below Align the Connecting Bolts in Partition with corresponding holes in Front, Shelf and Back. Now, making sure the Partition is completely on the Connecting Bolts, turn Cams to Locked Position. FIG. 10 .
Step11. AttachCompartmentBottomand CompartmentBackto Partitionby guidingeachpieceonto ConnectingBolts in the Partition(as shownin FIG.11).Turn Camsto LockedPosition. FIG.
Step 12. Place or tap Caster Clips, Inserts, (1) Locking Caster, and (1) Non-Locking Caster into Right Side (as shown in FiG. 12A below). Attach Right Side by Aligning the Connecting Bolts in the Right Side to the holes in the Compartment Back and the Compartment Bottom (as shown in FIG.12). Turn Cams to Locked Position. After completing Step 12, carefully turn the Cabinet upright onto the Casters FIG. 12 aster Clip \ Caster,nsort _ Right Side I I v'3 L L ocking Caster FIG.
Step 13. Attach the (2) Leaf Support Wings to outside of Right and Left Sides, on right and one Left with (8) #8 x 5/8" Flathead Screws. Now, attach the (2) Bronze Strike Washers for the Round Magnet to each side with (2) #5 x 1/2" Flathead Screws (as shown in FIG. 13). FIG. 13 Left Wing Right Wing ignet #8x5/8" Flathead Screw NOTE: Support Wings are to fold toward rear of cabinet. Step 14.
Step 15. The Door may be hung using (6) #5 x 5/8" Flathead Screws (as shown in FIG. 15). Next attach the Door Knob using (1) 7/8" Bolt for Ceramic Knob or (1) 8/32 x 1" Bolt For Metal Knob, this is a 2 pc. Knob Assembly as shown in FIG. 15. A. White Ceramic Knob (98301 only) 2 pc. Metal Knob (98300 + 98302 only) FIG. 15.A Sleeve I / FIG.
PLEASENOTE: BESURETO KEEPGROVESINDRAWERPARTS(FORDRAWERBOTTOM)ALIGNEDWHEN ASSEMBLING THEDRAWER. Assembling the Drawer Begin Drawer assembly by inserting Drawer Connectors into the ends of the (4) Drawer Backs, (as shown in FIG. A), Push Connectors all the way into the Drawer Backs until the tabs lock into place. F/_/_'_ _Jl Drawer Back - E ___ Drawer Side - B Drawer ______ II I /Drawer Bottom - FIG.
Installing Sewing Machine into Your new Cabinet. It may be helpful to read the directions for operating the mechanism before proceeding with the following steps. See page 16, and FIG. 19 on next page. FIG. 16 Step 1. Swing out the Leaf Support Wings and open leaves. To prevent damage to Cabinet surface, place cushioning material just to the left of cut-out. Lay the machine on its back, on top of cushioning material. Step 2.
To assist in selecting the platform machine, refer to FIG. 18B below. holes best suited to properly position your sewing Fit Insert (Sears #9801) FIG. 18B Cabinet top Opening Sewing Machine Determine measurement A & B on your custom-fit plastic insert and select platform holes which will properly place your machine in the cabinet top opening to allow it to fit with the insert when sewing in the flatbed position.
HOW TO MOVE YOUR MACHINE FROM ONE POSITION TO ANOTHER To move machine from free arm to flatbed (see Photos A, B& C). GENTLY push down on sewing machine until you hear a "click." The sewing machine is now locked in place at the flatbed _osition, To move machine from flatbed to storage (see Photos C,D& E. GENTLY push down on sewing machine until you hear a "click," The sewing machine is now locked in place at the storage position. NOTE: Your mechanism is adjustable.
Wood Parts and Part Numbers A-Right Leaf B-Left Leaf D-Left Sidel_anel E-Right Side Panel ge G-Back F-Partition H-Compartment Back (Left View) I-Shelf .... .... / J-Compartment Bottom /7 P-Drawer M-Platform • L-Right K-Left Leaf Supports . Front • Bottom Q-Drawer o/ O-Door Ref. No.
(JJ) (cc) }o))o I o 0 (o) D_ o 0 (KK) (DD) (uu)_ (E)_u__u_, (LL) (F) _\m_l (EE) @ (MM) (V' ,FFI (X) _ (GG) (oo) (HH) (L) _\-_'_-_-_-_ (PP) h-- (ss) ,.
Part Numbers :lef. No.
API Specialty Furniture (A Division of ARROW PRODUCTS, P.O. Box 410, Elkhorn, Inc.