Outdoor Storage User Manual

The mid frame pieces give rigidity to
the side and rear wall.
NOTENOTE
NOTENOTE
NOTE
Before installing mid frames
decide at which location you
want the entrance door. Do not
install the 1x2 mid frame at 1 of 3
locations.
1 1
1 1
1 Fasten a
rear frame assemblyrear frame assembly
rear frame assemblyrear frame assembly
rear frame assembly to
the main wall panels using screws.
2 2
2 2
2 Fasten a
right right
right right
right and
left front frameleft front frame
left front frameleft front frame
left front frame
to the front wall panels the same way.
3 3
3 3
3 Attach 4
frame supportsframe supports
frame supportsframe supports
frame supports to the
middle of the 2
truss columnstruss columns
truss columnstruss columns
truss columns using
2 bolts and nuts on each.
4 4
4 4
4 Fasten
side frame 7914 side frame 7914
side frame 7914 side frame 7914
side frame 7914 to the rear
corner panel using screws. Be sure
set of holes 1" in from end of frame is
installed toward rear of building.
Where rear frame overlaps side frame
in corner, fasten using 2 bolts and
nuts. Fasten opposite end to frame
support on truss column, using 2 bolts
and nuts in the 1st set of holes. Fas-
ten truss support to truss column at
bottom with 1screw at the 1st hole on
column. Support column assembly
with step ladder.
Step 8Step 8
Step 8Step 8
Step 8
BW21
Parts Needed For
FramesFrames
FramesFrames
Frames
12x17, 12x24 & 12x31 12x17, 12x24 & 12x31
12x17, 12x24 & 12x31 12x17, 12x24 & 12x31
12x17, 12x24 & 12x31
7837 Side Frame (2) 7837 Side Frame (2)
7837 Side Frame (2) 7837 Side Frame (2)
7837 Side Frame (2)
6228 Frame Support (4) 6228 Frame Support (4)
6228 Frame Support (4) 6228 Frame Support (4)
6228 Frame Support (4)
7949 Side Wall Channel (1) 7949 Side Wall Channel (1)
7949 Side Wall Channel (1) 7949 Side Wall Channel (1)
7949 Side Wall Channel (1)
7951 Support Column (1) 7951 Support Column (1)
7951 Support Column (1) 7951 Support Column (1)
7951 Support Column (1)
21
#10-32 Square Nut
STEP
44
44
4
STEP
22
22
2
STEP
33
33
3
STEP
11
11
1
5 5
5 5
5 Fasten
side frame 7837 side frame 7837
side frame 7837 side frame 7837
side frame 7837 to the
front corner panel using screws. Fas-
ten overlap in corner. Fasten oppo-
site end to the frame support on truss
column, using 2nd set of holes. This
will leave a gap between side frame
and truss column.
STEP
66
66
6
For a 12x24 building repeat
column procedure here
Rear Frame Assembly (1) Rear Frame Assembly (1)
Rear Frame Assembly (1) Rear Frame Assembly (1)
Rear Frame Assembly (1)
7834 Right Front Frame (1) 7834 Right Front Frame (1)
7834 Right Front Frame (1) 7834 Right Front Frame (1)
7834 Right Front Frame (1)
7835 Left Front Frame (1) 7835 Left Front Frame (1)
7835 Left Front Frame (1) 7835 Left Front Frame (1)
7835 Left Front Frame (1)
7917 Truss Column (see below) 7917 Truss Column (see below)
7917 Truss Column (see below) 7917 Truss Column (see below)
7917 Truss Column (see below)
7914 Side Frame (see below) 7914 Side Frame (see below)
7914 Side Frame (see below) 7914 Side Frame (see below)
7914 Side Frame (see below)
STEP
55
55
5
STEP
77
77
7
#8Ax5/16" Screw
7837
7835
7834
#10-32x7/16" Bolt
7917
7949
8531
7951
8532
7914
SIDE
REAR
GAP
1st HOLE
ON COLUMN
7837
7914
1st SET
OF HOLES
2nd SET
OF HOLES
6228
7917
7837
FRONT OF BUILDING
6 6
6 6
6 Fasten
side wall channelside wall channel
side wall channelside wall channel
side wall channel to the
rear corner panel using screws.
7 7
7 7
7 Fasten
support columnsupport column
support columnsupport column
support column to side
frame and side wall channel using
bolts and nuts where shown. Fold
corner panel slightly away from col-
umn to fasten bolts from outside. See
Step 12 for rear door installation.
IF YOU ARE BUILDING A 12x24
Each side of building will have 2 column
assemblies and 2 extra side frames 7914.
IF YOU ARE BUILDING A 12x31
Each side of building will have 3 column
assemblies and 4 extra side frames 7914.
GAP
Support this truss column with a
step ladder until next step