Owner's Manual & Assembly Instructions SS01 Model No. RH1014-C1 697.68615-A1 714880808 BUILDING DIMENSIONS * Size rounded off to the nearest foot *Approx. Size Foundation Size Storage Area Sq. Ft. Cu. Ft. 10' x 14' 121" x 160 1/4" 129 3,0m x 4,0m 307cm x 407cm 12,0m2 952 27,0m3 CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION.
BEFORE YOU BEGIN.... A2 Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model.
PLAN AHEAD.... A3 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools.
SAFETY FIRST.... A4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. •Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.
CARE & MAINTENANCE.... A5 Web Finish: For long lasting finish, periodically clean and wax the exterior surface. Touchup scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter.
ACCESSORIES.... A6 WEB ROOF STRENGTHENING (heavy snow load) KITS FLOOR FRAME KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%. ANCHOR KITS Model No. AK4 Anchor Kit contains heavy-duty steel augers, 60' (18m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 7
THIS PAGE WAS LEFT BLANK INTENTIONALLY 8
Foundation F09 The Foundation For Your Building OPTION 1: ARROW FLOOR FRAME KIT: (Order No. FB1014-A or 68387-A) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. To support a plywood deck B. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground.
Anchoring A10 Anchoring Down The Building It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Arrow Anchoring Kit: (Model No. AK4 or 60298) Recommended for use with any suggested base. Contains: 4 Anchors with Cable, Clamps and installation instruction. Anchoring into Wood/Post: Use 1/4" Wood Screws. There are 1/4" (0,63cm) dia. holes provided in the frames for proper anchoring. 1. 2.
Hardware SS11 Remove from bag of screws and save for the last step 65103 #8-32 Hex Nut (217) 65900A #10Bx1/2" Black Screw (8) (Packed with Screws) 65923 #8-32x3/8" Bolt (217) 65004 #8Ax5/16" Screw (454) 66045 Handle (2) 66646 Washer (368) (11 sheets of 40) 6228 Track Support (2) 67468 Peak Cap (6) (Arrow Logo) 66769 Door Slide (4) 66382 Lower Door Guide (4) 66183 Roof Trim Cap (2 right & 2 left) 67545 21' Weather Stripping (1) 67293 10' Weather Stripping (1) 11
Parts List SS12 Assembly Key No.
Assembly by Key No.
Step 1 ● 8934 Ramp (1) ● 9367 Front Floor Frame (2) ● 8936 Rear Floor Frame (2) ● 10387 Side Floor Frame (4) ● Parts Needed For ● Floor Frame Assemblies SO14 The front floor frame is made up of three pieces. The side floor frames and the rear floor frame are made up of two pieces. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. The illustrations below show the proper overall length for the sides, rear and front.
● Parts Needed For ● Step 2 ● 5986 Rear Wall Angle (2) ● 10391 Side Wall Angle (4) Frame Assemblies SS15 The main frame pieces reinforce the walls. These piece will later be installed at the top edge of the side walls and the rear wall. Proceed as follows: 1 Overlap the rear wall angle pieces as shown in the figure and fasten them together with one bolt in the center hole. 2 Make two side wall angles by overlapping the side wall angle pieces as shown.
Step 3 ● Parts Needed For ● Roof Beam Assemblies ● 10386 Roof Beam (12) SS16 The roof beams join the two gables and support the roof panels. The main roof beam is made up of four pieces overlapped back to back at the center. The left and right roof beam assemblies are made up of two pieces. Hint: These pieces are force-fitted, so you may have to press hard to join them together. 1 Place one end of a roof beam inside another roof beam so that the six holes in each piece align.
● Parts Needed For ● Step 4 Door Track Assembly ● 6403 Door Track Splice (1) ● 9366 Door Track (2) A17 NOTE: Door Track Splice (painted part) The door track assembly supports the sliding doors and reinforces the front wall. It is made up of three pieces. 6403 1 Using the door track splice, (painted), join the door track (galvanized) pieces end-to-end as shown. 2 Insert four screws from the under- 66769 9366 9366 side only.
Step 5 ● Front Floor Assembly (1) ● Side Floor Assembly (2) ● Rear Floor Assembly (1) ● Parts Needed For ● Floor Frame SO18 RIGHT REAR 10387 1 Place the floor frame pieces that STEP you assembled earlier on the foundation. Assemble the four corners of the floor frame using two screws at each corner as shown. At the front corners fasten bolts through from the bottom with nuts on top. 1 8936 FR ON T RIGHT FRONT 10387 9367 2 Measure the floor frame diagonally.
Step 6 ● Parts Needed For ● Posts/Top Frames SS19 NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. The top frame pieces give rigidity to the side walls and provide a surface for attaching the gables which support the roof.
● Parts Needed For ● Step 7 Splice Post ● 5287 Rear Splice Post (1) ● 5283 Side Splice Post (2) SS20 STEP 1 The splice posts support the walls. 1 Position a rear splice post at the 5287 center of the rear wall and fasten using 2 nuts and bolts into rear wall angle and 2 screws into rear floor frame. Hint: Measure or count holes to determine if post is centered on rear. 2 Fasten side splice posts to the sides of building using screws into side wall angles and side floor frames.
● Parts Needed For ● Step 8 Door Jamb ● 7311 Door Jamb (2) SS21 The door jambs reinforce the door opening and provide an attractive trim. 1 Fasten the top of the door jambs to the door track with two screws. Do the same for the bottom into frame. Notched edge faces toward center of building.
Step 9 ● Parts Needed For ● Studs/Front Channel ● 9344 Siding Stud (10) ● 9365 Front Wall Channel (2) SS22 1 Following dimensions, place studs between corner and splice post. Position stud inside top angle and fasten with a screw. 2 Rest bottom tab (large hole) outside floor frame. Do not fasten tab at this time. Repeat procedure for the remaining studs around the building. 3 Fasten front wall channel to the door jamb and corner post using screws.
● Parts Needed For ● Step 10 ● 9193 Side Siding (5 board) (12) ● 8736 Rear Siding (5 board) (6) ● 8737 Front Siding (5 board) (6) Side/Rear/Front Siding SS23 Each screw in the wall requires a washer. 1 Slide side siding (5 board) into channels of corner and splice posts, flat edge upward, slotted edge down resting on floor frame. Always follow this pattern. Fasten lower edge and tab of stud to floor frame using screws. Fasten center to stud with screws. Do not fasten top edge yet.
Step 11 ● 7858 Large Right Gable (2) ● 7859 Large Left Gable (2) ● 6114 Small Right Gable (2) ● 6115 Small Left Gable (2) ● 6085 Roof Beam Bracket (4) ● 7860 Mid Gable Brace (4) ● Parts Needed For ● Gable Assemblies ST24 67521 Edge Trim (Plastic Piece) The gables go on top of the front and rear walls to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing.
Step 12 ● Parts Needed For ● Gables/Roof Beams ● Left Gable Assemblies (2) ● Right Gable Assemblies (2) ● Single Roof Beam Assemblies (4) ● 6636 Gable Brace (2) ST25 1 Lift and fasten a right and left gable, under angle at corner, to the door track and rear wall angle with screws. Hint: On the front gable, leave out 2 screws closest to center gable leg. On the rear gable, use a bolt and nut at the overlapping rear wall angle.
● Parts Needed For ● Step 13 ● Main Roof Beam Assembly (1) ● 6227 Roof Beam Brace (2) Roof Beam/Braces SS26 1 Fasten the track supports to the front gable assembly only, as shown. STEP 1 2 Wrap the weather stripping along the mating edge of the large left and right gables as shown. Cut the weather stripping to length. Track Supports 6228 3 Spread the two halves of the double STEP roof beam and fasten to the gable brace of the front gable.
Step 14 ● Parts Needed For ● ● 7862 Right Roof Panel (1) Right Roof Panel ST27 Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer. 7863 2 1 7862 7861 4 3 7861 7861 6 5 7861 7861 8 7 7861 7861 10 9 7861 7862 12 11 7863 STEP NOTE Measure the building diagonally again and make adjustments to make sure the building is square and level.
● Parts Needed For ● Step 15 ● 7863 Left Roof Panel (1) ● 7861 Roof Panel (2) ● 6797 Ridge Cap (3) Roof Assembly ST28 1 Install a left roof panel at the left Screws To Roof Beam rear corner of the roof. 2 Install two roof panels in the sequence shown on previous page. Follow fastener sequence while fastening roof panels. NOTE Narrow roof panel rib (with bead on it) is always overlapped by wide rib of adjacent panel.
● Parts Needed For ● Step 16 ● 7861 Roof Panel (4) ● 6869 Ridge Cap (3) Roof Assembly ST29 1 Install four roof panels as you unroll the weather stripping tape, and press it down, install the second ridge caps 6869 overlapping the first ridge caps. Cover the notched areas of the roof panels with strips of weather stripping tape. Align the holes and fasten using bolts and nuts. NOTE If roof beam holes do not line up with the roof panel holes, shift the building from left to right.
● 7861 Roof Panel (2) ● 7863 Left Roof Panel (1) ● 6797 Ridge Cap (3) ● 7862 Right Roof Panel (1) ● Parts Needed For ● Step 17 Roof Assembly ST30 1 Install two roof panels, left roof panel, three ridge caps 6797 and right roof panel on the front of the roof as before. 2 Fasten the roof panel ribs, peak caps and ridge caps together using bolts and nuts. 3 Fasten the lower end of the panels to the side wall angles using screws and washers.
● Parts Needed For ● Step 18 Roof Trim ● 6893 Left Side Roof Trim (2) ● 6892 Right Side Roof Trim (2) ● 6015 Side Roof Trim (2) ST31 1 Attach the right and left side roof trim to the lower end of the roof panels on each side of the building using screws at each panel overlap. NOTE A single screw fastens both trim pieces at the overlap.
Step 19 ● 3719 Door Handle Brace (2) ● 10472 Right and Left Doors (2) ● 10497 Horizontal Door Brace (4) ● 6301 Vertical Door Brace (2) ● Parts Needed For ● Door Assembly SS32 The steps on this page tell how to assemble the right door. You will perform exactly the same procedures for the left door. Each bolt and screw in the door requires a washer. Proceed as follows: 66045 10497 1 Attach the door handle brace and 66045 3719 6301 handle to the door with 1 bolt as shown. Don't tighten the bolt yet.
Step 20 ● Parts Needed For ● ● Right Door Assembly (1) ● Left Door Assembly (1) Door Installation & Adjustment SQ33 Gable Horizontal Door Brace Door Track Door Slide 1 Door From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front frame track. STEP STEP 1 2 2 Position the top of the door so that the holes in the door line up with the holes in the door slides.
SOME FACTS ABOUT RUST SO34 SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears. 1.