User's Manual

43
● Parts Needed For ●
Roll-Up-DoorRoll-Up-Door
Roll-Up-DoorRoll-Up-Door
Roll-Up-Door
Step 27Step 27
Step 27Step 27
Step 27
BX43
●●
●●
●
9506 Door Panel (1) 9506 Door Panel (1)
9506 Door Panel (1) 9506 Door Panel (1)
9506 Door Panel (1)
●●
●●
●
9507 Door Panel Lock section (1) 9507 Door Panel Lock section (1)
9507 Door Panel Lock section (1) 9507 Door Panel Lock section (1)
9507 Door Panel Lock section (1)
●●
●●
●
9508 Door Panel Bottom Section (1) 9508 Door Panel Bottom Section (1)
9508 Door Panel Bottom Section (1) 9508 Door Panel Bottom Section (1)
9508 Door Panel Bottom Section (1)
●●
●●
●
67667 Left Vertical Track (1) 67667 Left Vertical Track (1)
67667 Left Vertical Track (1) 67667 Left Vertical Track (1)
67667 Left Vertical Track (1)
●●
●●
●
67666 Right Vertical Door Track (1) 67666 Right Vertical Door Track (1)
67666 Right Vertical Door Track (1) 67666 Right Vertical Door Track (1)
67666 Right Vertical Door Track (1)
STEP
22
22
2
STEP
11
11
1
STEP
66
66
6
STEP
33
33
3
NOTENOTE
NOTENOTE
NOTE
When rib neck bolts are inserted
in the track, use bolts with heads
located on the inner side of the
track to prevent interference with
the movement of the rollers.
11
11
1Repeat procedure for the third
doordoor
doordoor
door
panelpanel
panelpanel
panel using
#3 hinges#3 hinges
#3 hinges#3 hinges
#3 hinges at end stiles
and #1 hinge at middle stile.
22
22
2Insert the
rollerroller
rollerroller
roller shaft into the barrel
holes on the hinges furthest out from
the face of the end stiles on all 3
panels. Note that #1 hinge has only
1 barrel. Insert rollers through the
tabs on the bottom brackets on bot-
tom section.
33
33
3Attach
rightright
rightright
right and
left vertical tracksleft vertical tracks
left vertical tracksleft vertical tracks
left vertical tracks
loosely to right and left track supports
using 1/4-20x1/2" hex head bolts and
square nuts.
44
44
4Attach spring latch
strikers strikers
strikers strikers
strikers loosely
to vertical tracks using 1/4-20x1/2"
rib neck bolts and square nuts.
55
55
5Lift the bottom section and insert
the rollers into the vertical tracks. Slide
the panel down and level across top.
Shim to level if necessary.
66
66
6Insert lock section into vertical
tracks. Attach hinges from #1 to #2
panel by inserting #10Bx1/2" truss
head screws at bottom edge of lock
section.
77
77
7Position third
door paneldoor panel
door paneldoor panel
door panel and fas-
ten in the same manner. Do not
fasten the last door panel at this time.
STEP
55
55
5
9506
9507
Door Panel Lock Section
Door Panel
STEP
77
77
7
9508
LEVEL
Right Vertical
Track 67666
1/4-20x1/2"
Rib Neck Bolt
Striker
STEP
44
44
4
Roller
Insert Roller Shaft
only in barrel hole
shown!
#2
or #3
Hinge
LEFT TRACK
SUPPORT
Square Nut
Square Nut
67667
1/4-20x1/2"
Hex Head Bolt