01V 719180814 Owner’s Manual & Assembly Guide www.arrowsheds.com Model No. DSSCBW Series Storage Chest PATENT PENDING Customer Service: 1-800-851-1085 or assist@arrowsheds.com Gloves must be worn at all times to reduce risk of injury! UNIT DIMENSIONS Storage Area Exterior Dimensions (Lid Edge to Lid Edge) Interior Dimensions (Wall to Wall) Width Depth Height Width Depth Height 10 Sq. Ft. 22 Cu. Ft.
BEFORE YOU BEGIN... 02L Safety precautions MUST be followed at all times throughout the construction of your Storage Unit! •Care must be taken when handling various pieces of your Storage Unit since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your Storage Unit. •Practice caution with the tools being used in the assembly of your Storage Unit. Be especially familiar with the operation of all power tools.
HARDWARE LIST... Part No. AA Part Description 03V Qty.
PARTS LIST... Part No. 04V Part Description Qty.
ASSEMBLY BY KEY NO.
Step 1 You will need for this page: BB II (QTY: 3) (QTY: 8) 06V HH • Back Panel - C (QTY:1) • Bottom Air Spring Pedestal - HH (QTY: 2) • Corner Support - H (QTY: 4) 1 Attach the Bottom Air Spring Pedestal to the Back Panel by using Screws provided with Bottom Air Spring Pedestal. Push Bottom Air Spring Pedestal downward and tighten Screws as shown in Figure A. 2 Attach four (4) Corner Supports to Back Panel using eight (8) Hardware BB as shown in Figure B. DO NOT TIGHTEN SCREWS.
Step 2 07V You will need for this page: DD BB EE (QTY: 4) (QTY: 4) (QTY: 8) II (QTY: 3) • Front Panel - B (QTY: 1) • Plastic Handle - G (QTY: 1) • Corner Support - H (QTY: 4) 1 Install the Plastic Handle on the Front Panel using four (4) Hardware DD and four (4) Hardware EE as shown in Figure D. 2 Attach four (4) Corner Supports to Front Panel using eight (8) Hardware BB as shown in Figure E. DO NOT TIGHTEN SCREWS.
Step 3 08V You will need for this page: • Lid Panel - A (QTY: 1) • Top Air Spring Pedestal - GG (QTY: 2) GG 1 Attach Top Air Spring Pedestal to Lid Panel using Screws provided with Top Air Spring Pedestal as shown in Figure G. A GG Fig.
Step 4 09V You will need for this page: • Back Panel Assembly (Step 1) BB • Front Panel Assembly (Step 2) • Strength Ribs - F (QTY: 20) (QTY: 5) 1 Assemble Front Panel Assembly, Back Panel Assembly, and five (5) Strength Ribs together using twenty (20) Hardware BB as shown in Figure H. F F BB Fig.
Step 5 10V You will need for this page: BB • Bottom Panel - E (QTY: 1) (QTY: 12) 1 Attach the Bottom Panel using twelve (12) Hardware BB as shown in Figure I. C B E BB E Fig.
Step 6 11V You will need for this page: AA BB (QTY: 8) (QTY: 8) 1 2 3 EE (QTY: 8) FF • Left/Right Panel - D (QTY: 2) (QTY: 8) Attach one (1) Left/Right Panel using four (4) Hardware FF and four (4) Hardware EE as shown in Figure J. Attach Left/Right Panel at Corner Support using four (4) Hardware AA as shown in Figure K. Attach Left/Right Panels to Bottom Panel using four (4) Hardware BB as shown in Figure L. Repeat for other Left/Right Panel. EE D FF D Fig. J B C E AA D D D BB Fig.
Step 7 12V You will need for this page: CC EE (QTY: 9) 1 2 (QTY: 4) • Lid Panel Assembly (Step 3) • Air Spring - JJ (QTY: 2) Connect the Lid Panel Assembly to assembled box using nine (9) Hardware CC and nine (9) Hardware EE as shown in Figure M. Insert both ends of Air Spring into Top Air Spring Pedestal and Bottom Air Spring Pedestal. A C D JJ CC D B EE Fig.
CARE & MAINTENANCE... 13V Exterior Care: For a long lasting finish clean the exterior surface. We recommend washing with a mild soap solution. DO NOT use power washing, bleach, ammonia, or caustic cleaner to clean your storage unit. Using a spray automotive type wax periodically on the exterior is highly recommended if you are in a high humidity or coastal climate region. Combustibles must be stored in air tight containers designed for combustible storage.
ASSEMBLY NOTES 14 46A
ASSEMBLY NOTES 15 46A
