01CG 722660517 Owner’s Manual & Assembly Guide Model No. EZ8772HVCR EZ8772HVCRCC EZ8772HVCC EZ8772HVCCCR Gloves must be worn at all times to reduce risk of injury! www.arrowsheds.com EZ8772HVCREU EZ8772HVCRCCEU EZ8772HVCCEU EZ8772HVCCCREU 8’ x 7’ Nominal Size EZEE SHED Customer Service: 1-800-851-1085 or assist@arrowsheds.com BUILDING DIMENSIONS Approx.† Size 8’ x 7’ 2,4 m x 2,1 m Storage Area 49 Sq. Ft. 329 Cu. Ft. 2 4,5 m 9,3 m3 * See Inside for Detailed Safety Information.
GB: Assembly manual in additional languages available online. Scan QR code below to access. FR: Manuel de montage disponible en ligne dans d’autres langues. Pour y accéder, scannez le code QR ci-dessous. SP: Manual de montaje en idiomas adicionales disponible online. Escanee el código QR a continuación para acceder. DE: Montageanleitung in zusätzlichen Sprachen online verfügbar. Scannen Sie den QR-Code unten, um darauf zuzugreifen. IT: Manuale dell’assemblea in altre lingue disponibile online.
SAFETY PRECAUTIONS... 02CG Safety precautions MUST be followed at all times throughout the construction of your building! Care must be taken when handling various pieces of your building since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. Practice caution with the tools being used in the assembly of this building. Be especially familiar with the operation of all power tools.
ASSEMBLY TIPS & TOOLS 03A Watch the Weather Closely: Be sure the day you choose to install your building is dry and calm. Do NOT attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Use Teamwork: Two or more people are required to assemble your building. One person can hold the parts or panels in place while the other person fastens them together and handles the tools. This makes the process of assembling your building faster and safer.
04A FREQUENTLY ASKED QUESTIONS Q. How long will it take to assemble the building? A. Assembly time depends on a variety of factors, including roof design, tools available, DIY skill and the pace at which you work. Guidelines for each shed assembly are approximate AFTER completion of the base, and assume two or more people working on the assembly. Generally, you should plan on at least one day working with someone who can assist you; again, after constructing the base.
05A Q. What kind of base do I use? A. You can: •Use an Arrow Base Kit •Pour a concrete slab •Build a wood deck/floor (use exterior-grade plywood) •Use patio blocks •Build on crushed gravel, dirt or grass Arrow provides a base kit accessory that is an option for most building sizes. If you are building a wood deck/floor, an Arrow floor frame kit on top of your deck/floor assembles in minutes and provides a floor frame suitable for a 5/8” exterior-grade plywood floor (not included).
Q. What if the rear wall angle and channels are too large to fit inside of the rear wall panels? A. Check the dimensions of wall assemblies. They should be slightly smaller than the floor 06A frames. Lay the assemblies on top of the rear floor frame and pull them up to the top of the wall panels causing the corner panels to stand erect and not lean inward. Caution: Be careful to not scratch the panels on the way up. Q. The wide rib always overlaps the crimped rib. Is there ever an exception? A.
CARE & MAINTENANCE... 44A Exterior Care: For a long lasting finish, clean and wax the exterior surface. We recommend washing with a mild soap solution. DO NOT use power washing to clean your shed. Using a spray automotive type wax periodically on the exterior is highly recommended if you are in a high humidity or coastal climate region. Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible storage.
HARDWARE LIST... 08CG Hardware Views by Key No. Key Part No. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 65923 65103 65004 66646 66715 66718 66720 60H 66860 66847 66719 66713 66721 10280 Part Description Qty.
PARTS LIST... Key Part No. No.
ASSEMBLY BY KEY NO.
ASSEMBLY BY KEY NO.
ASSEMBLY OVERVIEW 12CG Build Side Wall Assemblies Build Rear Wall Assembly Build Front Wall Assembly Assemble Walls Build Roof Assemblies Install Gables and Roof Beam 12
ASSEMBLY OVERVIEW Install Roof Panels Install Trim Install the Door and you now have a finished shed 13 13CG
CONSTRUCTING A BASE... 14CG OPTION 1: Directly on ground (earth) Assemble your building directly on level ground (grass, dirt, rock, sand, etc.). Allow 1 - 2 hours for construction. OPTION 2: Wood Platform If you decide to build your own base, be sure to select the appropriate materials.
Step 1: Side Walls You will need for this page: (QTY: 4) (QTY: 4) 1 10305 4 10297 4 Wall Channel Floor Channel 11019 4 Channel Splice Make two (2) Wall Channel Assemblies (Painted). 10305 11019 10305 15CG 10305 11019 10305 2 Make two (2) Floor Channel Assemblies (Unpainted). 10297 11019 10297 10297 11019 10297 3 4 Turn Channel over and insert Channel Splice. Use Tapered end to start. Use rubber mallet and gently tap Channel Splice into Channel untill mounting holes align.
Step 1: Side Walls You will need for this page: 10998 10 Panel Wall 6 10999 2 11000 2 Panel Wall Corner Panel Make two (2) Side Wall Sections. 6 panels & 1 corner - each Be cautious when maneuvering and placing Panels. Once Panels begin to go up it is important to be able to finish in a timely manner to reduce the possibility of wind damage to your building.
Step 1: Side Walls 17CG MUST USE FLAT SOLID SURFACE. DO NOT SNAP ON GROUND OR GRASS Top Panel ALWAYS COVER THE ARROW 7 8 Raise Panel at Angle. Top Panel Bottom Panel Overlap Panels and Align Ends. maintaining pressure Always cover the Arrow. 9 10 Bottom Panel Hook Edge of Top Panel to Bottom Panel. Bring Top Panel down flat while maintaining pressure in the middle to keep edge hooked. Apply pressure in area shown 11 Start in middle of assembly to snap Panels together.
Step 1: Side Walls 18CG You will need for this page: ARROW TO TOP (QTY: 8) 14 Install Corner Panel. 15 Cover Arrow on Corner Panel. CORNER PANEL 10999 16 Use edge of surface, like your carton, to allow Corner Panel to hang down. 17 18 18 11000 Push down to snap Panels together working from the center in each direction . Attach Corner Panel to Wall Panel using four (4) washers and screws.
Step 1: Side Walls You will need for this page: 2 19CG IMPORTANT START ASSEMBLY AT CORNER PANEL Wall Channel Assembly 19 Channel Attach Wall Channel Assembly (Painted). CORNER MUST BE AGAINST 45 DEGREE CUT ON CHANNEL ELEVATE PANELS TO MAKE INSTALLING WALL CHANNEL ASSEMBLY EASIER WALL CHANNEL ASSEMBLY (Painted) 20 Align Wall Channel Assembly to Panel Ribs and pop into place at Corner. ARROW TO TOP ELEVATED PLATFORM 21 1.
Step 1: Side Walls You will need for this page: 2 22 IMPORTANT 10280 4 Floor Channel Assembly 20CG START ASSEMBLY AT CORNER PANEL CORNER MUST BE AGAINST 45 DEGREE CUT ON CHANNEL Corner Clip Attach Floor Channel Assembly (Unpainted). ELEVATE PANELS TO MAKE INSTALLING WALL CHANNEL ASSEMBLY EASIER Channel Corner Panel CORNER CLIP FLOOR CHANNEL ASSEMBLY (UNPAINTED) ELEVATED PLATFORM 1. Angle Floor Channel Assembly Wall Panels Channel 2.
Step 2: Rear Wall You will need for this page: (QTY: 2) (QTY: 2) 1 10341 2 10340 2 Wall Channel Floor Channel 11019 21CG 2 Channel Splice Make one (1) Wall Channel Assembly (Painted). 10341 11019 10341 2 Make one (1) Floor Channel Assembly (Unpainted). 10340 11019 10340 3 4 Turn Channel over and insert Channel Splice. Use Tapered end to start. Use rubber mallet and gently tap Channel Splice into Channel untill mounting holes align.
Step 2: Rear Wall You will need for this page: (QTY: 4) 1 10998 6 10999 Panel Wall Panel Wall ARROW TO TOP 6 22CG 11000 1 Corner Panel Make one (1) Rear Wall Section. Be cautious when maneuvering and placing Panels. Once Panels begin to go up it is important to be able to finish in a timely manner to reduce the possibility of wind damage to your building. MUST USE FLAT SOLID SURFACE.
Step 2: Rear Wall You will need for this page: 23CG IMPORTANT 1 START ASSEMBLY AT CORNER PANEL Wall Channel Assembly 10 Attach Wall Channel Assembly (Painted). CORNER MUST BE AGAINST 45 DEGREE CUT ON CHANNEL Channel ELEVATE PANELS TO MAKE INSTALLING WALL CHANNEL ASSEMBLY EASIER 11 Align Wall Channel Assembly to Panel Ribs and pop into place at Corner. WALL CHANNEL ASSEMBLY (Painted) ARROW TO TOP ELEVATED PLATFORM 12 1.
Step 2: Rear Wall You will need for this page: 1 Floor Channel Assembly 13 24CG IMPORTANT 10280 2 START ASSEMBLY AT CORNER PANEL CORNER MUST BE AGAINST 45 DEGREE CUT ON CHANNEL Corner Clip Attach Floor Channel Assembly (Unpainted). ELEVATE PANELS TO MAKE INSTALLING WALL CHANNEL ASSEMBLY EASIER Channel Corner Panel CORNER CLIP FLOOR CHANNEL ASSEMBLY (UNPAINTED) ELEVATED PLATFORM 1. Angle Floor Channel Assembly Wall Panels Channel 2.
Step 3: Front Wall You will need for this page: (QTY: 4) 1 2 (QTY: 2) 10341 2 10340 2 Wall Channel Floor Channel Make one (1) Wall Channel Assembly (Painted). 2 11019 25CG 10291 1 Channel Splice 10292 1 Header Trim Ramp 10341 11019 10341 Make one (1) Floor Channel Assembly (Unpainted). 10340 11019 4 10340 3 Turn Channel over and insert Channel Splice. Use Tapered end to start. Use rubber mallet and gently tap Channel Splice into Channel untill mounting holes align.
Step 3: Front Wall You will need for this page: (QTY: 2) ARROW TO TOP 11024 (QTY: 6) 7 2 Door Jamb 10999 Panel Wall 2 26CG 11000 Corner Panel Make one (1) Front Wall Section. DOOR JAMB 1 MUST USE FLAT SOLID SURFACE. DO NOT SNAP ON GROUND OR GRASS. 11024 DOOR JAMB 11024 10999 10999 VERIFY PANELS ARE POSITIONED IN CORRECT SEQUENCE BY PART 8 Door Jambs always on top of Wall Panel.
Step 3: Front Wall You will need for this page: 1 1 Wall Channel Assembly Floor Channel Assembly 12 10280 2 27CG IMPORTANT START ASSEMBLY AT CORNER PANEL Corner Clip Channel CORNER MUST BE AGAINST 45 DEGREE CUT ON CHANNEL Attach Wall Channel Assembly (Painted). WALL CHANNEL ASSEMBLY (Painted) CORNER CLIP 13 FLOOR CHANNEL ASSEMBLY (UNPAINTED) Attach Floor Channel Assembly (Unpainted). IMPORTANT START ASSEMBLY AT CORNER PANEL CORNER MUST BE AGAINST 45 DEGREE CUT ON CHANNEL 1.
Step 3: Front Wall 28CG You will need for this page: (QTY: 4) (QTY: 4) 15 17 Secure Wall Channel Assembly (Painted) using two (2) washers and screws. 16 Secure Floor Channel Assembly (Unpainted) using two (2) screws. 28 Secure Header Trim to Wall Channel Assembly (Painted) using two (2) washers and screws. 18 Secure Ramp to Floor Channel Assembly (Unpainted) using two (2) screws.
Step 4: Right Door Assy You will need for this page: 11017 (QTY: 6) (QTY: 2) 1 1 Vertical Door Brace 11026 1 Vertical Door Brace 11025 1 Door Astragal 66715 1 Door Handle 66721 6 U-Nut (Door Clip) Attach U-Nuts onto Vertical Door Brace. U-NUT (2X) TYPICAL (3) PLACES U-NUT (2X) 11017 2 U-NUT (2X) Attach Door Handle to Vertical Door Brace using two (2) screws and Astragal using six (6) washers and screws.
Step 4: Right Door Assy You will need for this page: 1 11010 (QTY: 4) 11011 Door Panel Door Panel 1 10301 2 30CG 2 Vertical Door Brace Assy Horizontal Door Brace ARROW TO TOP 3 Overlap Door Panels, align ends and snap Panel Ribs together. MUST USE FLAT SOLID SURFACE. DO NOT SNAP ON GROUND OR GRASS. 11011 11010 HOLES 4 10301 Attach Horizontal Door Braces to Door Panels. HOLES 5 Attach Vertical Door Brace Assemblies to Door Panels using two (2) washers and screws per assembly.
Step 4: Right Door Assy You will need for this page: (QTY: 3) (QTY: 8) 10295 2 Diagonal Door Brace 6 Turn Door over. 7 Attach Diagonal Door Braces to Door Panels using three (3) screws. 10295 10295 8 Install four (4) washers and screws for Horizontal Door Braces. 9 Turn Door over. 10 Install four (4) washers and screws for Diagonal Door Braces.
Step 5: Left Door Assy You will need for this page: 11017 (QTY: 2) 1 Vertical Door Brace 11027 1 Vertical Door Brace 1 66721 6 U-Nut (Door Clip) 66716 1 Padlock Eyelet Attach U-Nuts onto Vertical Door Brace. U-NUT (2X) TYPICAL (3) PLACES U-NUT (2X) 11017 2 U-NUT (2X) Attach Padlock Eyelet to Vertical Door Brace using two (2) screws.
Step 5: Left Door Assy You will need for this page: 1 11010 (QTY: 4) 11011 Door Panel Door Panel 1 10301 2 33CG 2 Vertical Door Brace Assy Horizontal Door Brace ARROW TO TOP 3 Overlap Door Panels, align ends and snap Panel Ribs together. MUST USE FLAT SOLID SURFACE. DO NOT SNAP ON GROUND OR GRASS 11011 11010 HOLES 4 10301 Attach Horizontal Door Braces to Door Panels. HOLES 5 Attach Vertical Door Brace Assemblies to Door Panels using two (2) washers and screws per assembly.
Step 5: Left Door Assy You will need for this page: (QTY: 8) (QTY: 7) 10295 2 66719 Diagonal Door Brace Spring Pin Upper 6 66713 1 Spring Pin Lower Turn Door over. 7 8 SPRING PIN UPPER 1 Attach Diagonal Door Braces to Door Panels using three (3) screws. Install four (4) washers and screws for Horizontal Door Braces. 10295 10295 9 10 Attach Spring Pin Upper to Door using two (2) screws. Attach Spring Pin Lower to Door using two (2) screws. 11 34CG SPRING PIN LOWER Turn Door over.
Step 6: Roof pre-assy You will need for this page: (QTY: 8) 10334 4 10335 4 Roof Channel Roof Channel 1 11019 4 Channel Splice Make four (4) Roof Channel Assemblies (Painted). 10335 11019 10334 10335 11019 10334 10335 11019 10334 10335 11019 10334 2 3 Turn Channel over and insert Channel Splice. Use Tapered end to start. Use rubber mallet and gently tap Channel Splice into Channel untill mounting holes align. 11019 11019 12" m 5c 30, 10335 4 10334 35 Join Channels and screw together.
Step 6: Roof pre-assy You will need for this page: 11020 4 (QTY: 16) Roof Beam 5 11020 Make two (2) Roof Beam Assemblies using (8) nuts and bolts for each.
Step 6: Roof pre-assy You will need for this page: 2 80119 Roof Panel Left (QTY: 8) ARROW TO TOP 6 11012 10 11013 Roof Panel Roof Panel Right Make two (2) Roof Sections. 7 Always cover the Arrows. 11012 80119 HOLES ROOF CHANNEL ASSEMBLY (Painted) 11012 2 4 11021 Roof Channel Assembly 4 Fascia Trim MUST USE FLAT SOLID SURFACE. DO NOT SNAP ON GROUND OR GRASS Overlap Panels and Align Ends. Snap panel ribs together.
Step 6: Roof pre-assy You will need for this page: 2 11022 1 38CG 1 11023 Roof Beam Assembly (QTY: 16) Ridge Cap ARROW TO TOP 10 Ridge Cap Attach Roof Beam Assembly (from page. 35) to Roof Section using seven (7) washers and screws. 11013 80119 2X EDGE OF ROOF SECTION ROOF BEAM ASSEMBLY NOTE: LARGE HOLES IN ROOF BEAM ASSEMBLY FACE DOWN. ROOF BEAM ASSEMBLY SIDE VIEW SIDE VIEW 11 EDGE OF ROOF SECTION Attach Ridge Caps to Right Roof Section using two (2) washers and screws.
Step 7: Wall Assembly You will need for this page: 1 Side Wall Assembly (QTY: 4) CORNER PANEL ON TOP OF WALL PANEL Corner Clip Corner Panel Wall Panel 39CG 1 Rear Wall Assembly 1 Attach Side Wall and Rear Wall. 2 Attach Side Wall to Rear Wall using four (4) washers and screws at corner. A IT IS HIGHLY RECOMMENDED THAT AT LEAST 2 PEOPLE ARE PART OF ASSEMBLY.
Step 7: Wall Assembly 40CG You will need for this page: 1 1 Side Wall Assembly Front Wall Assembly Install Corner Clip IT IS HIGHLY RECOMMENDED THAT AT LEAST 2 PEOPLE ARE PART OF ASSEMBLY. 3 Attach Side Wall and Front Wall.
Step 7: Wall Assembly You will need for this page: (QTY: 12) 4 Attach remaining Walls using four (4) washers and screws at each corner.
Step 8: Gable & Beam Assy You will need for this page: (QTY: 14) (QTY: 12) 11020 4 10994 2 Gable Right Roof Beam 1 80115 2 Gable Left 1 11049 1 Header Angle Assemble Roof Beams using two (2) nuts and bolts. 11020 2 11020 11020 Overlap Length 7” (17,8 cm) 11020 80 3/4” (205,1 cm) Finished Length 2 Snap Gables onto Upper Channel Attach Roof Beam Assemblies together using (10) nuts and bolts. 3 Gable 10994 Install (REAR) Gable Right and Gable Left using three (3) screws in each.
Step 8: Gable & Beam Assy You will need for this page: (QTY: 8) 11043 2 (QTY: 8) Gable Brace 5 11043 4 7905 Roof Beam Brace 43CG 1 Roof Beam Assembly Install Gable Braces using two (2) nuts and bolts in each and Roof Beam Braces using (2) washers, nuts and bolts in each. 7905 11043 OPEN HOLES 7905 7905 7905 6 43 Install Roof Beam Assemblies to Gables using (4) nuts and bolts.
Step 9: Roof Assembly You will need for this page: (QTY: 12) 1st 1 2nd Attach Roof Sections using twelve (12) screws through Roof BeamCenter into Roof Channels.
Step 9: Roof Assembly You will need for this page: (QTY: 22) (QTY: 12) 66860 2 Peak Cap 60H 4 45CG 66847 4 Corner Cap Vent 2 Attach Roof Sections to building using nine (9) washers and screws each. 3 Place Peak Caps between Ridge Cap and Roof Sections secure using two (2) washers and screws each. 66860 66860 11022 4 Attach Corner Caps and Vents to building using twelve (12) screws.
Step 9: Roof Assembly You will need for this page: (QTY: 8) 5 Attach Roof Beam Assembly to Roof Beam Brace using two (2) nuts and bolts each .
Step 9: Roof Assembly You will need for this page: 9204 (QTY: 4 6 2 Roof Beam Brace Attach Roof Beam Brace to Gable Brace and Roof Beam-Center using two (2) nuts and bolts each . NOTE: FLANGE ON ROOF BEAM BRACE LOCATED BETWEEN ROOF BEAM-CENTER AT FOURTH (4) HOLE FROM END.
Step 10: Door Assembly You will need for this page: (QTY: 12 1 (QTY: 14) 66718 6 Hinge 1 Right Door Assembly Attach three (3) Hinges to each Door Jamb using two nuts and bolts in each hinge. 48 1 Left Door Assembly 2 Attach Right Door Assembly and Left Door Assembly to Hinges using two (2) screws in each hinge. 3 Secure Ramp to Floor Channel Assembly (Unpainted) using two (2) screws.
ARROW ACCESSORIES... 49CG ANCHOR KITS FLOOR FRAME KITS Anchor Kit contains heavy-duty steel augers, 60' (18 m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground. For buildings MODELS FB47410, FB5465, FB106-A, FB109-A, FB1014-A, FBSDS108, and FKEZEE A simple floor frame system made of heavy-duty, hot-dipped galvanized steel. Use as base for plywood, sand or stone. Model No.
ANCHORING OPTIONS... 50CG IMPORTANT: It is important that building be anchored after construction. these are recommended ways of anchoring. Anchor into Wood or Concrete Arrow Anchoring Kit: (Model No. AK100 or 68383) For wood platform. Use Decking Screws. For concrete slab. Use Lag Screws. Recommended for use with the concrete base. Contains: Corner gussets, perimeter clips, hardware, 1/4" masonry drill bit and installation instructions. Arrow Anchoring Kit: (Model No.
ASSEMBLY NOTES 51 46A
