01L 01L 718061113 Owner’s Manual & Assembly Guide R TM www.arrowsheds.com Customer Service: 1-800-851-1085 or assist@arrowsheds.com Gloves must be worn at all times to reduce risk of injury! PATENT PENDING UNIT DIMENSIONS Storage Area Exterior Dimensions (Lid Edge to Lid Edge) Interior Dimensions (Wall to Wall) Width Depth Height Width Depth Height 10 Sq. Ft. 21 Cu. Ft.
BEFORE YOU BEGIN... 02L Safety precautions MUST be followed at all times throughout the construction of your Storage Unit! •Care must be taken when handling various pieces of your Storage Unit since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your Storage Unit. •Practice caution with the tools being used in the assembly of your Storage Unit. Be especially familiar with the operation of all power tools.
HARDWARE LIST... Key No. Part No. Part Description Qty.
PARTS LIST... Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Part No. 10682 10683 10685 10686 10687 10688 10689 10690 10691 10692 10693 10694 10695 6481 10697 10698 10696 Part Description Floor Section Front & Rear Floor Section Front & Rear Floor Channel Side Floor Channel Lid Handle Panel Wall Panel Corner Panel U-Splice Lid Stay Brace Lid Handle Brace Front Top Channel Rear Top Channel Side Top Channel Gusset Lid Support Lid Panel Lid End Cap 04L Qty.
ASSEMBLY BY KEY NO. 05L NOTE: The U-Splice, Key No. 8 (Part No. 10690) is used at each Panel connection.
Step 1 You will need for this page: SB SFB (QTY: 4) (QTY: 1) 06L 69953 9 Plastic Foot 10682 4 Floor Section 10683 2 10685 2 10686 2 F/R Floor Section F/R Floor Channel Side Floor Channel LNS 1 (QTY: 8) Assemble the Floor as shown and secure with four (4) Small Bolts and Nuts and one (1) Small Flat Head Bolt and Nut in between middle Floor Section. Add a Plastic Foot to the Small Flat head Bolt when attaching middle Floor Sections together. DO NOT TIGHTEN BOLTS AT THIS TIME.
Step 2 07L You will need for this page: IMPORTANT: IF STORAGE UNIT IS NOT SQUARE, LID WILL NOT CLOSE PROPERLY! 66798 1 Foam Tape 1 Once Floor is complete, measure diagonally. When the diagonal measurements are equal, the Floor is square. After Floor is square tighten bolts holding Floor Sections together. 2 Seal corners of Floor with Foam Tape. Cut four (4) 1” (2,5 cm) strips to place between Floor Channels at the corners.
Step 3 08L You will need for this page: PP (QTY: 6) 1 10687 1 10688 2 Lid Handle Panel Wall Panel 10690 2 U-Splice Pre-assemble Front Panels together using two (2) U-Splices and six (6) Push Pins leaving the top paired hole vacant. These holes will be used to attach the Lid Handle Brace in a later step. Paired holes and hinge holes at top. 10688 10687 10688 Single hole at bottom. Slide U-Splice over the Panels where the Panels meet and secure using Push Pins.
Step 4 09L You will need for this page: 10688 3 PP (QTY: 8) 1 Wall Panel 10690 2 U-Splice Pre-assemble Back Panels together using two (2) U-Splices and eight (8) Push Pins. Paired holes and hinge holes at top. 10688 10688 10688 Single hole at bottom. PP 10690 Slide U-Splice over the Panels where the Panels meet and secure using Push Pins. 10690 PP To help with aligning holes, use an awl. This will make inserting push pins easier.
Step 5 You will need for this page: PP (QTY: 16) 1 10L 10688 2 Wall Panel 10689 4 Corner Panel 10690 4 U-Splice Pre-assemble Side Panels together using two (2) U-Splices and eight (8) Push Pins. Make two (2) assemblies. Paired holes and hinge holes at top. 10689 10688 10689 Single hole at bottom. PP 10690 Slide U-Splice over the Panels where the Panels meet and secure using Push Pins. 10690 PP To help with aligning holes, use an awl. This will make inserting push pins easier.
Step 6 11L You will need for this page: SB LS (QTY: 6) 1 (QTY: 6) 10690 4 PP Assemblies from steps 3,4,&5: • A Front Panel Assembly (1) • B Back Panel Assembly (1) • C Side Panel Assembly (2) U-Splice (QTY: 16) Position each Panel Assembly as shown and secure to the Floor with one (1) Large Screw in the bottom leg of each Front and Rear Panel and Small Bolt in each Side Panel. Paired holes and hinge holes at top. C B A C SB LS Single hole at bottom.
Step 7 You will need for this page: SB (QTY: 6) 1 12L 66785 3 Lid Stay 10691 3 Lid Stay Brace Pre-assemble the Lid Stay to the Lid Stay Brace using two (2) Small Bolts and Nuts. Make three (3) assemblies. SB 66785 10691 2 Place the two (2) outside Lid Stay/Brace Assemblies into Back Corner Panel. DO NOT install, just set in place as shown and set third assembly aside for now.
Step 8 13L You will need for this page: SS SB (QTY:14) (QTY: 4) 1 10693 1 10694 1 Front Top Channel Rear Top Channel 10695 2 Side Channel 6481 2 Gusset 2 60H Corner Cap First install top channels starting with Front and Rear Channels, then install Side Channels using ten (10) Small Screws. When installing top channels, start on inside lip of wall panels then rotate to the outside.
Step 9 You will need for this page: SS (QTY: 2) 1 14L 10692 1 66792 1 Lid Handle Brace Locking T-Handle Bend end flaps down as shown before installation. 10692 Install Lid Handle Brace to Lid Handle Panel as shown using two (2) Small Screws. 10687 SS SS 10692 Slide Lid Handle Brace over U-Splice and secure using Small Screws. 10692 2 Install Locking T-Handle using two (2) Long Bolts which are packed with Locking T-Handle.
Step 10 15L You will need for this page: SS • Lid Stay/Brace Assemblies (3) (QTY: 12) 1 Install three (3) Lid Stay/Brace Assemblies into the back panels by angling them into place; one in each Back Corner Panel and one in Middle Panel. SS 2 Secure each Lid Stay/Brace Assembly using four (4) Small Screws. Two on top and two on botton of brace. First attach bottom of Lid Stay/ Brace Assembly, then attach top of the Lid Stay/Brace Assembly.
Step 11 16L You will need for this page: 66800 SB (QTY: 2) 1 (QTY: 2) 66796 1 10697 1 Lid Catch Lid Support For the middle Lid Support attach the Lid Catch using two (2) Small Bolts, Lock Washer, and four (4) Nuts. 66796 #8 Lock Washer 10697 SB SB Loosen top nut to adjust fit between Latch and Lid Catch.
Step 12 You will need for this page: LS (QTY: 12) 1 PSS / SS SS (QTY: 24) (QTY: 6) 17L 10697 5 Lid Support 10696 2 66786 6 End Cap Strap Lid End Cap 10698 1 Lid Panel Start lid assembly by attaching five (5) Lid Supports to the Lid Panel using twenty (20) Small Screws. Make sure all Lid Supports are facing the same way with middle Lid Support having the Lid Catch mounted to it. SS Lid Catch Hinge holes at the bottom.
Step 13 18L You will need for this page: LS (QTY: 9) 1 (QTY: 6) 66784 3 FSS FB SS (QTY: 3) (QTY: 6) Offset Hinge Install three (3) Hinges using six (6) Flat Head Bolts and three (3) Flat Head Self Tapping Screws. FB FB FSS FB Inside 2 3 Secure lid to base by attaching all three (3) Hinges to lid using nine (9) Large Screws. Attach the three (3) Lid Stays to the Lid using six (6) Small Screws.
Step 14 You will need for this page: 19L 66797 Latch 1 1 66801 1 Plastic Spacer Install Latch and Plastic Spacer to the inside of the Locking T-Handle. Secure with Push Nut found in the Locking T-handle packaging. Pay careful attention to position of Latch. 2 Adjust Lid Catch as needed to ensure Latch completely locks into place as shown below. Lid Catch Latch Loosen top nut to adjust fit between Latch and Lid Catch.
CARE & MAINTENANCE... 20L Exterior Care: For a long lasting finish clean and wax the exterior surface. We recommend washing with a mild soap solution. DO NOT use power washing to clean your storage unit. Using a spray automotive type wax periodically on the exterior is highly recommended if you are in a high humidity or coastal climate region. Combustibles must be stored in air tight containers designed for combustible storage.
