Owner's Manual & Assembly Instructions AK01 Model No. YS47 A TSCYS47H4 A Missing Parts, Questions on Assembly? Call: 1-800-851-1085 or assist@arrowsheds.com Do not return to dealer, they are not equipped to handle your requests. 723030817 Storage Area: 26 Sq. Ft. 2,4 m2 BUILDING DIMENSIONS *Approx. Size 697.68601 A YS47EU A YS47Z A 154 Cu. Ft.
GB: Assembly manual in additional languages available online. Scan QR code below to access. FR: Manuel de montage disponible en ligne dans d’autres langues. Pour y accéder, scannez le code QR ci-dessous. SP: Manual de montaje en idiomas adicionales disponible online. Escanee el código QR a continuación para acceder. DE: Montageanleitung in zusätzlichen Sprachen online verfügbar. Scannen Sie den QR-Code unten, um darauf zuzugreifen. IT: Manuale dell’assemblea in altre lingue disponibile online.
BEFORE YOU BEGIN.... A03 Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model.
PLAN AHEAD.... A04 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools.
SAFETY FIRST.... A05 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. •Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.
CARE & MAINTENANCE.... A06 Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter.
A07 ACCESSORIES.... FLOOR FRAME KITS ROOF STRENGTHENING (heavy snow load) KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof. BEFORE AFTER ANCHOR KITS Model No. AK4 Anchor Kit contains heavy-duty steel augers, 60' (18 m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground.
ORDERING ACCESSORIES.... A08 02/13 We recommend that you purchase accessory items from your local storage building dealer whenever possible; however, because the full line of accessories is not always available from all dealers, Arrow is offering them to you on a direct basis. There are two ways to order Arrow Storage Building Accessories: Option 1 Option 2 Accessories can be purchased through Order accessories by telephone using your MasterCard or Visa credit card. arrowsheds.
BR9 Base The Base For Your Building OPTION 1: ARROW FLOOR FRAME KIT: (Order No. FB47410) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. To support a plywood deck B. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground. Allow 1 - 2 hours for construction.
Anchoring BR10 Anchoring Down The Building It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring into Wood/Post: Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm) dia. holes provided in the frames for proper anchoring. Anchoring into Concrete: Arrow Anchoring Kit: (Model No. AK100 or 68383) 1. For poured concrete slab or footing or patio blocks: Use 1/4" x 2" (6 mm x 51 mm) Lag Screws. 2.
Hardware AK11 65103 #8-32 Hex Nut (10) 65941 #6-32 Hex Nut (23) (Packed with Screws) 65923 #8-32x3/8" (10 mm) Bolt (10) 65004 #8Ax5/16" (8 mm) Screw (222) 66714 #6-32x7/16" (11 mm) Flat Hd Bolt (23) (Packed with Screws) 66692 #10ABx1" (25 mm) Screw (2) (Packed with Screws) 66646 Washer (160) (4 sheets of 40) 66022 Gray Foam Tape (1) 66684 Spring Latch (2) 66462 Hasp (1) 66016 Facia Cap (1 Right and 1 Left) 66463 Swivel Staple (1) 66604 Hinge (4) 67293 Foil Tape (1) 11
Parts List AK12 Assembly Key No.
Assembly by Key No.
Step 1: Right Door Assembly AK14 New You will need for this page: Right Door 2 Horizontal Door Brace 11057 1 Door Latch Brace Hasp 11058 2 Diagonal Door Brace 11059 2 Attach HASP to FRONT SIDE of RIGHT DOOR using three (3) bolts and nuts. 66714 66462 1 Diagonal Door Brace 9788 (QTY: 1) 66462 65941 9794 11057 2 3 Slide the Door Latch Brace into the middle of the Door and securing it with four (4) Screws.
Step 1: Continued You will need for this page: 66604 2 FB (QTY: 4) Hinge 4 Attach Hinges to Door using four (4) Flat Head Bolts and Nuts.
Step 2: Left Door Assembly You will need for this page: 9787 1 (QTY: 4) (QTY: 11) 1 Left Door 9794 2 Horizontal Door Brace 11057 1 Door Latch Brace 66463 1 11058 2 11059 2 Swivel Staple Diagonal Door Brace Diagonal Door Brace Attach SWIVEL STAPLE to FRONT SIDE of LEFT DOOR using four (4) bolts and nuts. 9787 66714 66463 65941 2 Tapered end up. 1 9792 (QTY: 1) Door Stop Slide the Door Latch Brace into the middle of the Door. Attach the Door Latch Brace and Door Stop using seven (7) Screws.
Step 2: Continued You will need for this page: FB (QTY: 4) (QTY: 8) 66604 2 Hinge AK17 66684 2 Top Latch Spring 66684 4 Attach Hinges to Door using four (4) Flat Head Bolts and Nuts. 5 Attach both Top and Bottom Latch Springs to left side of Door using six (6) Screws. 6 Attach both Top and Bottom Horizontal Door Braces to right side of Door using one (1) Screw each.
Step 3 AK18 9796 Ramp (1) 9795 Floor Frame (2) 8977 Side Floor Frame (2) Parts Needed For Floor Frame Assembly RIGHT REAR 1 Center the ramp on top of the floor 8977 STEP 2 frame. Note that the door can be installed on either end. Join the frames by inserting four screws. 9795 STEP 1 2 Assemble the four corners of the floor frame using two screws at each corner as shown. 8977 9796 FRO NT 9795 3 Measure the floor frame diagonally.
Step 4 Parts Needed For Corner Posts/Rear Siding AK19 NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. 9793 Corner Post (2) 8075 Rear Siding (1) 9793 9793 1 Fasten two corner posts to the rear corners of the floor frame assembly using four screws.
Step 5 6481 Gusset (4) 9793 Corner Post (2) 8074 Side Siding (2) Parts Needed For Corner Posts/Side Siding AK20 1 Attach a gusset to each end of the two corner posts using one screw. TOP VIEW 2 Fasten one corner post assembly to the front corner of the floor frame assembly using two screws. Caution! Once corner post is attached, fasten one side siding to the corner posts with six screws. Do not fasten flat edge now.
Step 6 Parts Needed For Headers/Frame/Jambs AK21 1 Fasten side eave frame behind top of corner posts using two screws, top leg facing inside building. Note: For left end door location, fasten side eave frame as shown. For right end door location fasten side eave frame on opposite side of building. STEP STEP 3 2 Rear Header 8062 Front Header 9791 2 Fasten front header behind top of corner posts/gussets using one bolt and nut on each end.
Step 7 8074 Side Siding (2) 8075 Rear Siding (1) 8067 Siding Stud (3) 8068 Siding Stud (2) Parts Needed For Side/Rear Siding/Studs AK22 1 STEP Position the side siding (6 board) to corner posts, flat edge of siding upward and bottom resting on 1st side siding. See figure. Always follow this pattern. Fasten siding to corner posts using six screws. Do not fasten flat edge now. Position 2nd side siding on opposite side of building and fasten as before.
Step 8 Parts Needed For Gables/Peak/Roof Frames AK23 8061 Left Gable (1) 8060 Right Gable (1) 8069 Side Peak Frame (1) 8066 Roof Frame (2) NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. Side Peak Frame Fasten at Lower Hole 1 Lift and fasten a left gable on top of header, with lower leg under side eave frame at corner, using screws.
Step 9 Parts Needed For 8074 Side Siding (2) Side Siding/Foam Tape AK24 Foam Tape Installing the siding to the roof is best done with a step ladder. NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the siding fit better, and holes will align. 4th Side Siding Protective Paper Apply Gray Foam Tape 1 After the 3rd side siding is fastened to the 2nd, roll it over on the roof and fasten as before.
Step 10 8073 Top Siding (1) 8080 Peak Trim (1) 8078 Right Wall Trim (1) 8079 Left Wall Trim (1) 8076 Right Roof Trim (1) 8077 Left Roof Trim (1) Parts Needed For Top Siding/Trim AK25 1 Fasten remaining top siding (5 board), to the top side of building. 2 Fasten peak trim to peak of roof using screws thru siding into frame. STEP STEP 3 3 Apply foil tape by overlapping sid- FR ing by 1/2" (13 mm), pressing firmly into contour of siding, from top to bottom of gables.
Step 11 AK26 Parts Needed For Door Assembly 1 Position doors in corners of door opening as shown and fasten hinges with 7/16" (11 mm) flat head bolts and #6 hex nuts. When spring latch is engaged with hole in header or ramp, these will hold left door closed when not it use. The hasp and staple can be used to keep doors closed, or used with a padlock (not supplied) to lock doors.
YS47 A 697.68601 A TSCYS47H4 A YS47EU A YS47Z A AK27 Anchoring and Floor Frame Anchoring Anchor your building at this time. Floor Frame If you have purchased a Floor Frame Kit you need to install it at this time. SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use.
