Installation Guide

ManualsBrandsArt Decor ManualsCurtain RodsKontur Wood 106 in. Single Traverse Rod Set in Ebony with Endcap in Antique

KONTUR EVO

INSTALLATION INSTRUCTIONS

STEP 1 - Installing Supports

OUTSIDE POST

CARRIERS

COVER PLATE

INSIDE POST

BACK PLATE

STEP 2 - Splice track if necessary

CENTER

SUPPORT

SET SCREWS

SPLICE

STEP 4 - Installing Outside Posts

STEP 3 - Attach Quadra if necessary

STEP 4 - Attach Return if necessary

1. Join the track sections

together.

2. Tighten set screws.

3. Screw Center Support

directly into center hole

of Splice.

4. Cover splice with

Splice Cap after

installation is complete.

OUTSIDE POST

FINIAL

VALANCE JOINER

M-6 BOLT COVER PLATE INSIDE POST

1. Install Back Plate to wall. Make sure all M-6 bolts are level.

If you have a spliced track the Center Support must be

installed at the position of splice.

2. Cover Back Plate with Cover Plate.

3. Screw on Inside Post very securely. Do not leave any play.

1. Install Valance Joiner to Quadra. Flip Joiner when installing

from left side and right side ﬁ nials.

2. Slide Support brick into Joiner channel. Install screw but leave

slack. Slip screw over Valance joiner and tighten.

1. Insert Support Brick into the Return’s Joiner Track.

2. Attach Ballast with screw onto Return, do not completely tighten.

3. Insert Support Brick into Rail Joiner Track.

Install screw into Support Brick but leave slack.

4. Slip slack screw into Ballast and line up Return and Rail so

Return reaches back edge of Rail. Tighten both screws.

5. Place Corner Cover over Return and Rail Corner. Tighten top

screws till Corner Cover is secure.

1. Loosen all screws on Outside Posts.

2. Slide Ouside Posts into back channel of Rail.

3. Align Outside Posts with Inside Posts from Step 1.

Height calculation for regular clips.

Add 1 1/8” to length of drapes, plus at least 1/2” clearence

from the ﬂ oor. This measurement is the distance from ﬂ oor to

center point of Back Plate.

Please note drapes should not touch rail,

install pin on hooks with this in consideration.

BALLAST

CORNER COVER

Summary of content (3 pages)

PAGE 1
KONTUR EVO INSTALLATION INSTRUCTIONS STEP 1 - Installing Supports OUTSIDE POST STEP 3 - Attach Quadra if necessary FINIAL CARRIERS VALANCE JOINER COVER PLATE BACK PLATE 1. Install Valance Joiner to Quadra. Flip Joiner when installing from left side and right side ﬁnials. 2. Slide Support brick into Joiner channel. Install screw but leave slack. Slip screw over Valance joiner and tighten. INSIDE POST Height calculation for regular clips.
PAGE 2
STEP 4 - Mount rail onto supports STEP 6 - Cord Draw Systems, Installing Pulley 1. Attach pulley to cord. Stretch pulley until cord is tight. It is not necessary to use excessive tension. Mark spot with pencil on wall or ﬂoor. Remove cords and install pulley then re-install cords. 2 1 3 1. Slide Outside Posts over Inside Posts. 2. Once all Outside Posts including Center Supports are in place, tighten posts securely by turning clockwise. 3. Tighten set screws. 4. Finished result for Center Supports. 5.
PAGE 3
INSTALLATION D’UNE MISE À JOUR EURO-SCOPE KONTUR, NEXGEN, TEKNO 25, TEKNO 40 ÉTAPE 1 - Assemblage du rail lorsque le splice est inclus ÉTAPE 3 - L’installation du rail ÉTAPE 2 - Installing mounting hardware 1 2 1. Installez les embouts et insérez suite les glissière dans le rail. 2. Attachez le lance-rideau à la première glissière sur le côté desiré (ouverture à gauche ou à droite manuelle). ÉTAPE 4 - Installation du la poulie 3 4 5 6 1. 2. 3. 4.