INSTALLATION GUIDE STUDIO 55 SoundBar STUDIO 46 SoundBar STUDIO 39 SoundBar STUDIO55-SB STUDIO46-SB STUDIO39-SB
CARTON CONTENTS: 1. STUDIO SoundBar Speaker 2. Television Mounting Brackets (TMB) o (24” for STUDIO39-SB & STUDIO46-SB; 29” for STUDIO55-SB) 2. Long Extension Plates 2. Short Extension Plates 1. Hardware Accessory Kit o 1. 3mm Allen Wrench o 8. Bracket to Bracket (B to B) Screws, M5 x 10 mm, Stainless Steel o 4. Machine Screw, M4 x 11.5 mm o 4. Machine Screw, M5 x 11.5 mm o 4. Machine Screw, M6 x 11.5 mm o 4. Machine Screw, M8 x 11.5 mm o 4. Machine Screw, M10 x 11.5 mm o 4.
Thank you for choosing the Artison STUDIO SoundBar Speaker. We are pleased that you have selected our high-performance audio product. The following information will guide you through the installation of your Artison STUDIO SoundBar Speaker. INTRODUCTION Artison STUDIO SoundBars are designed to attach directly to any Flat Panel TV (FPTV) with the included hardware, brackets, and come with custom made grilles.
INSTALLATION OPTIONS The Artison STUDIO SoundBar Speakers were designed to have multiple installation options using the included hardware and brackets. Attachment to any Flat Panel TV (FPTV) in a Tablestand or Wall Mounted installation. On-Wall/Surface Mounting. Please read the instructions below before attempting your installation. INSTALLATION PROCEDURES The Television Mounting Brackets were designed in compliance with the VESA Mounting Standards.
FIGURE 1 FIGURE 2 FIGURE 3 5
EXTENSION PLATE SELECTION BASED ON FPTV THICKNESS 6. Depending on the FPTV depth the use of Extension Plates will vary. Refer to the following; TABLE 1 and FIGURES 4-9. Figure FPTV Thickness Extension Plate 4&5 6&7 8&9 1.0 - 1.4” 1.9 - 2.8” 2.7 – 3.6” No Short Long TABLE 1 FIGURE 4 6 Minimum TV Wall Mount Bracket Depth 1.0" 1.0" 1.
FIGURE 5 7
FIGURE 6 8
FIGURE 7 9
FIGURE 8 10
FIGURE 9 11
HARDWARE KIT 7. Mounting Screw Selection 7.1.1. Match the threads in the FPTV chassis to one from the kit. Thread: M4, M5, M6, M8, or M10. 7.1.2. First, check the thread depth of the mounting points on the FPTV. 7.1.3. Using the Television Mounting Brackets (Depth = 6.5mm), third party wall-mount, and washers. Allow for 5 - 8 mm of screw threads into the FPTV chassis. Be sure to account for the maximum thread depth into the TV. 8. Flat Washer: Select a washer that fits around the selected Mounting Screw.
MOUNTING THE SOUNDBAR TO THE TELEVISION MOUNTING BRACKETS 13. Using the correct accessories from STEP 6 assemble the SoundBar to the Television Mounting Bracket using the B/B hardware and the 3 mm Allen Wrench. There are Two sliders in the cabinet that will accept these screws. Simple slide the sliders to meet the Television Mounting Brackets location. 14. Carefully adjust the speaker forward to sit just behind the bezel. 15. See FIGURES 10 & 11.
16. Attach the grille to the cabinet by slipping the grille around the cabinet. You will feel a click as the grille seats. See FIGURES 12 & 13. 17. Tighten the B/B hardware to hold the position. 18. Slide the grille Left or Right to align with the sides of the FPTV bezel.
WIRING THE SOUNDBARS 3 CHANNEL METHOD (Left, Center and Right) 1. Operate the terminals by firmly pressing on them. An opening will be exposed in the side of the terminal. Slip about 9 mm (3/8”) of bare speaker wire into this opening hole and release the terminal. The spring loaded terminal will now securely hold the wire in place. 2. Attach the three speaker wire pairs to the binding posts on the rear of the SoundBar.
FINE TUNING YOUR STUDIO SOUNDBAR Satellite / Subwoofer Crossover Frequencies: STUDIO 39: ‘SMALL’ Speaker on A/V Receiver / Processor Left / Right Crossover Frequency: 100 Hz Center Crossover Frequency: 80 Hz STUDIO 46: ‘SMALL’ Speaker on A/V Receiver / Processor Crossover Frequency: 80 Hz STUDIO 55: ‘SMALL’ Speaker on A/V Receiver / Processor Crossover Frequency: 80 Hz 16
SPECIFICATIONS & DIMENSIONS: Studio 55 SoundBar STUDIO55-SB Dimensions: 4.1” x 53.4” x 2.2”, HWD Overall 4.7” x CUSTOM” x 2.7”, HWD w/ Minimum Grille For use with FPTV’s: W ≥ 54.1” Driver Complement: 6. 3½” Carbon Fiber, Long Throw, Midrange/Woofer 3. 25 mm XT25 Super Audio Tweeters 2.
Studio 46 SoundBar STUDIO46-SB Dimensions: 4.1” x 44.7” x 2.2”, HWD Overall 4.7” x CUSTOM” x 2.7”, HWD w/ Minimum Grille For use with FPTV’s: W ≥ 45.4” Driver Complement: 6. 3½” Carbon Fiber, Long Throw, Midrange/Woofer 3. 25 mm DX25 Super Audio Tweeters 2.
Studio 39 SoundBar STUDIO39-SB Dimensions: 4.1” x 37.5” x 2.2”, HWD Overall 4.7” x CUSTOM” x 2.7”, HWD w/ Minimum Grille For use with FPTV’s: W ≥ 38.0” Driver Complement: 4. 3½” Carbon Fiber, Long Throw, Midrange/Woofer 3. 25 mm DX25 Super Audio Tweeters 2.
STUDIO GRILLE Cloth Colors: Black and Light Grey Dimensions: 4.75” x Custom to TV Width x 1.75”, HWD Minimum Width 38.0” for STUDIO39-SB Minimum Width 45.4” for STUDIO46-SB Minimum Width 54.
LIMITED WARRANTY This warranty remains in effect for five years from the date of purchase for speaker products and one year for electronic products. THIS WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZED ARTISON DEALER IN THE UNITED STATES. THE ORIGINAL BILL OF SALE MUST BE PRESENTED WHENEVER WARRANTY SERVICE IS REQUIRED.
