User's Manual

ManualsBrandsArts Electronics ManualsAudio EquipmentTURNTABLE AUDIO SYSTEM

ENGLISH

Setting the clock (1)

Set the current time before using the unit.

You can set the clock when the unit is in standby.

1 Press the STANDBY/ON button to put

the unit into standby.

NOTE

When the ring around the button is not lit blue, the

unit is in standby. Note that the clock cannot be set

when the unit is on.

2 Press and hold the CLOCK ADJUST but-

ton for at least 2 seconds.

Press and hold for at

least 2 seconds

“SET CLOCK” scrolls across the display.

3 Press the TIME (j/k) buttons to switch

between 24 HOUR and 12 HOUR (24-

hour or 12-hour time display).

o If a setting is left for more than 20 seconds, this

time setting mode will end.

4 Press the CLOCK ADJUST button again.

Display example

The “hour” value blinks.

5 Press the TIME (j/k) buttons to set

the current hour.

Continued on the next page

LP-P1000_OM_EF_vA_CS6.indb 25 2013/09/11 16:16

Summary of content (12 pages)

PAGE 1
Setting the clock (1) Set the current time before using the unit. You can set the clock when the unit is in standby. 1 Press the STANDBY/ON button to put the unit into standby. oo If a setting is left for more than 20 seconds, this time setting mode will end. ENGLISH NOTE When the ring around the button is not lit blue, the unit is in standby. Note that the clock cannot be set when the unit is on. c3 4 Press the CLOCK ADJUST button again.
PAGE 2
Setting the clock (2) 6 Press the CLOCK ADJUST button. Current time display The clock is always shown when the unit is in standby mode (off ) and when the function is set to PHONO/ AUX. Display example Press the remote control's DISPLAY button to show the clock on the display. oo The current time is shown for 3 seconds in CD and FM/AM modes. The minute value blinks. 7 Press the TIME (j/k) buttons to set the current minute. Display example Current time 8 Press the CLOCK ADJUST button.
PAGE 3
Basic operation (1) 1 Press the STANDBY/ON button to turn the unit on. 3 Turn the VOLUME knob to adjust the volume. ENGLISH The ring around the STANDBY/ON button lights blue when on. oo Even when in standby (unit off ), pressing a function button will turn the unit on. 2 Press a function button to set the playback source. MIN (0): minimum volume MAX (40): maximum volume Turn the VOLUME knob right to raise the volume and left to lower it. oo The default value is 20.
PAGE 4
Basic operation (2) Adjusting the bass, treble and stereo balance 1 Press the SOUND button to select the item you want to adjust. Pressing the SOUND button cycles through the items in the following order. BASS Setting items and ranges BASS (low frequencies) Use to adjust the bass. Setting range: −5 to +5 Default value: 0 Display example TREBLE (high frequencies) Use to adjust the treble.
PAGE 5
Adjusting the brightness of the display Press the DIMMER button to cycle through the following brightness settings. Ordinary brightness Dim Muting the output Press the MUTE button to temporarily silence the output. Press the MUTE button again to resume output at the previously set volume level. Very dim ENGLISH oo When the unit enters standby, the dimmer setting is reset to ordinary brightness. oo When the mute function is active, “MUTE” appears on the display.
PAGE 6
Listening to a CD (1) 1 Press the CD/Bluetooth button to select CD. Press the CD/Bluetooth button again to switch between CD and Bluetooth. After switching to CD, “DISC” will appear, “READING” will blink for several seconds, and then the CD will be in a stopped state. If no disc is loaded, “NO DISC” appears on the display. 2 Press the open/close (- ) button to open the tray. The disc tray opens forward. 3 Place a disc centered on the tray with the labeled side up.
PAGE 7
Audio CD display example Total number of tracks 5 Press the play/pause (y/9) button. Total playback time MP3/WMA disc display example File number ENGLISH Folder number Playback will start from the first track and y will appear on the display. oo A non-audio disc might be “played” in the same manner as an audio disc, but sound will not be output. oo When a WMA disc is loaded, “WMA” will appear on the left side of the display.
PAGE 8
Listening to a CD (2) Pausing playback Press the play/pause (y/9) button to pause playback. When paused, press the play/pause (y/9) button to resume playback from the paused point. oo When paused, the playback time will blink. Stopping playback Press the stop (8) button to stop playback. 32 LP-P1000_OM_EF_vA_CS6.
PAGE 9
Skipping tracks/files Search for a part of a track ENGLISH During playback, turn the skip (.//) knob to skip to the previous or next track/file and start playback. Keep turning until you reach the desired track number. oo When stopped, after selecting a track with the skip (.//) knob, press the play/pause (y/9) button to start playback. oo During playback, turn slightly toward . to return to the beginning of the currently playing track. To play an earlier track, continue turning toward ..
PAGE 10
Programmed playback (1) Up to 32 tracks/files can be programmed in the desired order. Program tracks when playback is stopped. Programming tracks/files oo To stop programming, press the stop (8) button or wait 20 seconds or more. oo During programming if you do nothing for 20 seconds or more, the program will be confirmed. Example of display after program confirmation 1 Press the CD/Bluetooth button to select “CD”. 3 Select a track to add to the program. With an audio CD Use the skip/search (.
PAGE 11
To select a file by number, use the skip/search (.m/,/) buttons. 5 When you have finished adding tracks to a program, press the play/pause (y/9) button to start programmed playback. Display example File number oo This unit treats MP3/WMA files that are not in folders as being in the 001 (ROOT) folder. oo If you change the folder or file number, only the MEMORY indicator will blink. 4 Press the MEMORY button. ENGLISH Folder number oo To stop programmed playback, press the stop (8) button.
PAGE 12
Programmed playback (2) Checking the program order When stopped, press the MEMORY button to cycle through the program numbers and the programmed track numbers in order. 3 Press the MEMORY button. The track/file is added to the end of the program. Changing a track/file within the program Adding tracks to the end of the program 1 When stopped, press the MEMORY button repeatedly to show the number which is one higher than the last program number.