User`s manual

ARTURIA – MOOG MODULAR V 2.6 – USER’S MANUAL 153
completely adjust the nature of the support (hotline, forum on the website etc.), upgrades and
updates at any time.
The product registration is possible during the activation process or at any time later through
the Internet. In such a process you are asked to agree to the storage and use of your personal
data (name, address, contact, email-address, and license data) for the purposes specified
above. Arturia may also forward these data to engaged third parties, in particular distributors,
for support purposes and for the verification of the upgrade or update right.
5. License module (eLicenser Key and/or Soft-eLicenser)
Arturia uses a hardware device connected through the USB connection of a computer, the
"USB-eLicenser" and/or a protection scheme, the "Soft eLicenser" for license control (hardware
and/or software dongle). The USB-eLicenser and/or Soft eLicenser permanently saves the
license information and regulates access to the software. If an USB-eLicenser is required for
the use of the software, then the USB-eLicenser must be connected physically to the computer
through the USB interface.
For the activation of the software, updates or upgrades of the software the computer which is
connected to the Arturia key and/or using the Soft eLicenser or using the OEM software must
be connected to the server of eLicenser through the Internet. If the product was delivered with
the USB-eLicenser, the license information was already transferred to the USB-eLicenser. If
the product was delivered with a product card (without the USB-eLicenser), the activation
codes of the enclosed product card must be entered manually by the user upon installation and
the license information must be exchanged with the server of eLicenser.
In the event of OEM software, the activation codes will be send to an email-address submitted
by you during a registration and must be entered manually by the user upon installation and
the license information must be exchanged with the server of eLicenser.
The reinstallation of the software - on the same or another computer - is permitted only in
case the already installed software cannot be used any more (e.g. following deinstallation). If
the software does not use an USB-eLicenser, the new activation codes may be obtained from
the users online account for support created during the personal product registration. Further,
the activation codes must be entered manually by the user upon installation and the license
information must be exchanged with the server of eLicenser. Arturia may require for the
provision of further activation codes e.g. your proof of purchase (invoice, receipt) and a signed
assurance by fax or letter stating your name, address and that the already installed software
cannot be used any more.
You can also use another computer other than the one on which the software is to be installed
for the activation and transfer of license data to the USB-eLicenser, if the software is using an
USB-eLicenser. However, in such a case a corresponding access software (eLicenser Control
Centre, “eLCC”) must be installed on the computer connected to the Internet, which is subject
to a separate licensing agreement.
6. Defect and loss of the USB-eLicenser
In the case of a defect or damage to the USB-eLicenser Arturia or a third party engaged by
Arturia will check the USB-eLicenser. In the case of a legitimate claim the USB-eLicenser and
the licenses included shall be replaced in return for a handling fee. The licenses will only be
replaced provided that they are licenses issued by Arturia. Further claims against Arturia are
excluded.
Arturia assumes no liability or obligation if the USB-eLicenser is mislaid as a result of loss,
theft or otherwise. Arturia reserves the right to block the licenses saved on the USB-eLicenser
upon being notified by the registered user of the loss. The licenses saved on the USB-eLicenser
cannot be replaced.
7. No Unbundling
The software usually contains a variety of different files which in its configuration ensure the
complete functionality of the software. The software may be used as one product only. It is not
required that you use or install all components of the software. You must not arrange
components of the software in a new way and develop a modified version of the software or a
new product as a result. The configuration of the software may not be modified for the purpose
of distribution, assignment or resale.