APPLI A NC E S FOR L I V I NG AGH41B OPERATION MANUAL
Congratulations, you are now the proud owner of an ARTUSI cooking appliance. Thank you for purchasing ARTUSI and welcome to the ARTUSI Family. This instruction manual has been specially created to inform you of the full range of features your ARTUSI appliance has to offer and serves as an introduction to getting the very best out of your ARTUSI appliance. We present detailed information on each of the features your ARTUSI appliance consists of.
GENERAL NOTICE We invite you to read this instruction booklet carefully, before installing and using the equipment. It is very important that you keep this booklet together with the equipment for any future consultation. If this equipment should be sold or transferred to another person, make sure that the new user receives the booklet, so that they can learn how to operate the appliance and read the corresponding notice. This is a Class 3 appliance.
GENERAL NOTICE CUSTOMER SERVICE Before calling the customer service: In case of failure of the plan we raccommend: - check the correct insertion of the plug into the wall socket; - check that the gas supply is regular. If you do not locate the cause of the malfunction: - switch the appliance of and call your service.
INSTRUCTIONS FOR THE USER - Notice - When the equipment is not working, always check that the knobs are in the closing position (see fig.1). - If the flame should blow out accidentally, the safety valve will automatically stop the gas supply, after a few seconds. To restore operation, set the knob to the lighting point (large flame, fig.1). - While cooking with fat or oil, pay the utmost attention as these substances can catch fire when overheated. - Do not use sprays near the appliance in operation.
INSTRUCTIONS FOR THE USER 1 Burner 2 Flame safeguard sensor 3 Injector 4 Ignition spark plug If you have a problem with the cooktop, check the table below. You may be able to solve the problem and this will save you from paying for a service call. You will have to pay for a service call even in the warranty period if the problem is one listed below FAULT POSSIBLE CAUSES REMEDY Burner will not light even though the sparker is working.
INSTRUCTIONS FOR THE INSTALLER Important notice: The operations indicated below must be followed by authorised personnel exclusively, in conformity with the regulations in force. The manufacturing firm refuses all responsibility for damages to people, animals or things, resulting from the failure to comply with such provisions.
INSTRUCTIONS FOR THE INSTALLER IMPORTANT: A separation panel at least 10mm from the bottom of the cooktop must be included during installation to prevent access to the underside of the appliance. This panel can be made of any non-combustible rigid material. If the hob is going to be installed on the top of an oven, precautions must be taken to guarantee an installation in accordance with current accident prevention standards.
INSTRUCTIONS FOR THE INSTALLER Only install with a hose assembly that complies with AS/ANZ 1869 (AGA Approved), 10mm ID, class B or D, no more than 1.2m long and in accordance with AS/NZS 5601. and in particular section 4.8. Where a hose assembly is used and the cooktop is in the installed position, the hose assembly shall be suitable for connection to a fixed consumer piping outlet located at a point 800 850mm above the floor and in the region outside the width of the appliance to a distance of 250mm.
GAS TRANSFORMATIONS AND ADJUSTMENTS GAS CONVERSIONS AND ADJUSTMENTS After changing the injector, it is necessary to eliminate residual natural gas in the system. To do this you have to turn to the maximum position then press the knob of each burner and wait few seconds. Data Label A duplicate Data Label is supplied to adhere in an accessible area next to the appliance. This appliance is suitable for Natural Gas and Universal LPG; ensure that the available gas supply matches the Data Label.
MAINTENANCE Maintenance Schedule No regular maintenance is required for the hotplates except cleaning. Replacing the power supply cable If the power supply cable should be replaced, it is necessary to use a cable with a section of 3x0.75mm2, type H05VV-F or H05RR-F, complying with the regulations in force. The connection to the terminal board must be effected as shown in fig.11.
Close Maximum Minimum 350 1 2 3 4 5 6 495 SCREW ADJUSTMENT TUBE VENTURI A 7 8 11
B C A 9 10 WIRING DIAGRAM MODEL: AGH41B The manufacturing firm refuses all responsibility for any possible imprecision in this booklet, due to misprints or clerical errors. It reserves the right to make all the changes that it will consider necessary in its own products, without affecting the essential characteristics of functionality and safety.
13
FOR SPARE PARTS OR TO FIND THE ADDRESS OF YOUR NEAREST STATE SPARE PARTS CENTRE IN AUSTRALIA Distributes by Eurolinx pty Ltd Street: 48-50 Moore Street, Leichhardt N.S.
Warranty Card Worldwide Appliances Pty Limited A.B.N. 45868077422 Office: 48-50 Moore Street, Leichhardt N.S.W 2040 Post: Locked Bag 3000, Annandale, N.S.W 2038 P: 1300 694 583 WARRANTY REGISTRATION Your ongoing satisfaction with your artusi product is important to us. We ask that you complete the enclosed Warranty Registration Card and return it to us so that we have a record of the artusi product purchased by you.
Warranty Card continued 4. Time for Claim under the Warranty You must make any claim under this Warranty within twenty eight (28) days after the occurrence of an event which gives rise to a claim pursuant to the Warranty, by booking a service call on the telephone number below. 5. Proof of Purchase Customers must retain proof of purchase in order to be eligible to make a warranty claim in respect of an artusi product. 6.
DISCLAIMER Worldwide Appliances PTY LTD, trading as ARTUSI, is continually seeking ways to improve the design specifications, aesthetics and production techniques of its products. As a result alterations to our products and designs take place continually. Whilst every effort is made to produce information and literature that is up to date, this brochure should not be regarded as an infallible guide to the current specifications, nor does it constitute an offer for the sale of any particular product.