Spec Sheet

DATA SHEET
ARUBA 330 SERIES ACCESS POINTS
OTHER INTERFACES
• One HPE Smart Rate port (RJ-45, maximum negotiated
speed 5Gbps)
- Auto-sensing link speed (100/1000/2500/5000BASE-T)
and MDI/MDX
- 802.3az Energy Ecient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3at PoE
• One 10/100/1000BASE-T Ethernet network interface (RJ-45)
- Auto-sensing link speed and MDI/MDX
- 802.3az Energy Ecient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3at PoE
• Link aggregation (LACP) support between both network
ports for redundancy and increased capacity
• DC power interface, accepts 1.35/3.5-mm center-positive
circular plug with 9.5-mm length
• USB 2.0 host interface (Type A connector)
• Bluetooth Low Energy (BLE) radio
- Up to 4 dBm transmit power (class 2) and -91 dBm
receive sensitivity
- Integrated antenna with roughly 30 degrees downtilt
and peak gain of 5.1 dBi (AP-334/IAP-334) or 2.2 dBi
(AP-335/IAP-335)
• Visual indicators (tri-color LEDs): for System and Radio status
• Reset button: factory reset (during device power up)
• Serial console interface (RJ-45, RS232)
• Kensington security slot
POWER SOURCES AND CONSUMPTION
• The AP supports direct DC power and Power over
Ethernet (PoE)
• When both power sources are available, DC power takes
priority over PoE
• Power sources are sold separately
• Direct DC source: 48Vdc nominal, +/- 5%
- Interface accepts 1.35/3.5-mm center-positive circular
plug with 9.5-mm length
• Power over Ethernet (PoE): 48 Vdc (nominal)
802.3af/802.3at compliant source
- When using IPM, the AP may enter power-save mode
with reduced functionality when powered by a PoE
source (see details on Intelligent Power Monitoring in
this datasheet)
- Without IPM the AP will apply some xed restrictions
when using PoE:
- The USB interface is disabled when using an 802.3at
PoE power source
- The USB interface and second Ethernet port are
disabled, and both radios operate in 1x1 mode when
using an 802.3af POE power source
• Maximum (worst-case) power consumption: 25.3W
(802.3at PoE), 13.2W (802.3af PoE) or 25W (DC)
- Excludes power consumed by external USB device (and
internal overhead); this could add up to 5.9W (PoE or
DC) for a 5W/1A USB device
• Maximum (worst-case) power consumption in idle mode:
10.9W (PoE or DC)
MOUNTING
• The AP ships with two (white) mounting clips to attach to a
9/16-inch or 15/16-inch at T-bar drop-tile ceiling.
• Several optional mount kits are available to attach the
AP to a variety of surfaces; see the Ordering Information
section below for details
MECHANICAL
• Dimensions/weight (unit, excluding mount accessories):
- - 225mm (W) x 224mm (D) x 52mm (H)
8.9” (W) x 8.9” (D) x 2.0” (H)
- 1150g/41oz
• Dimensions/weight (shipping):
- 335mm (W) x 290mm (D) x 76mm (H)
13.2” (W) x 11.4” (D) x 3.0” (H)
- 1550g/55oz
ENVIRONMENTAL
• Operating:
- Temperature: 0° C to +50° C (+32° F to +122° F)
- Humidity: 5% to 93% non-condensing
• Storage and transportation:
- Temperature: -40° C to +70° C (-40° F to +158° F)
REGULATORY
• FCC/Industry of Canada
• CE Marked
• R&TTE Directive 1995/5/EC
• Low Voltage Directive 72/23/EEC
• EN 300 328
• EN 301 489
• EN 301 893
• UL/IEC/EN 60950
• EN 60601-1-1 and EN 60601-1-2