Aruba Instant On AP22 Access Point Installation Guide The Aruba Instant On AP22 access point delivers high performance concurrent 2.4 GHz and 5 GHz Wi-Fi 6 (802.11ax) functionality with MIMO radios (2x2 in 2.4 GHz, 2x2 in 5 GHz), while also supporting legacy 802.11a/b/ g/n/ac wireless services.
LEDs The AP22 access point has two LEDs that indicate the system and radio status of the device.
Reset Button The reset button located on the bottom of the device can be used to reset the access point to factory default settings. There are two ways to reset the access point to factory default settings: Reset the AP during normal operation Press and hold down the reset button using a small, narrow object such as a paper clip for more than 10 seconds during normal operation. Reset the AP while powering up 1.
Before You Begin Refer to the sections below before beginning the installation process. The AP22 access point is designed in compliance with governmental requirements so that only authorized network administrators can change the settings. Identifying Specific Installation Locations Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference.
The following sections provide instructions on how to use this mount bracket. Installing the Access Point to a Ceiling Tile Rail 1. Pull the necessary cables through a prepared hole in the ceiling tile near where the access point will be placed. 2. Place the mount bracket against the back of the access point with the mount bracket at an angle of approximately 30 degrees to the tabs (see Figure 4). 3. Twist the mount bracket clockwise until it snaps into place in the tabs (see Figure 4).
Figure 5 Mounting the AP to a 15/16” Ceiling Rail Figure 6 Mounting the AP to a 9/16” Ceiling Rail Installing the Access Point to a Solid Surface 1. Attach the mount bracket to any solid surface, such as a wall or hard ceiling, as shown in Figure 7. a. Install any necessary wall anchors. Wall anchors are not included in the package. b. Align the screw holes in the mount bracket with the previously installed anchors or demarcated screw points.
c. Insert two screws to secure the mount bracket. Screws are not included in the package. Figure 7 Attaching the Mount Bracket to a Solid Surface 2. Attach the access point to the secured mount bracket as shown in Figure 8. a. Align the access point with the mount bracket, placing the access point so that it’s mounting tabs are at an angle of approximately 30 degrees to the mount bracket. 3. Pushing towards the solid surface, rotate the access point clockwise until it clicks into place (see Figure 8).
Verifying Post-Installation Connectivity The integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing successfully (see Table 1). Mobile Application Installation Click the Apple App Store or Google Play badge below to download and install the Aruba Instant On mobile app to your phone. Launch the app and follow the instructions to complete the setup. Alternately, simply search for “Aruba Instant On” app within Apple App Store or Google Play.
Power over Ethernet (PoE): 802.3af or 802.3at compliant source If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an output rated 12Vdc, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in the US and Canada.
In accordance with Industry Canada regulations, this radio transmitter and receiver may only be used with an antenna, the maximum type and gain of which must be approved by Industry Canada. To reduce potential radio interference, the type of antenna and its gain shall be chosen so that the equivalent isotropic radiated power (EIRP) does not exceed the values necessary for effective communication. This device complies with Industry Canada's license-exempt RSS regulations.
5. No modifications are allowed without Aruba approval. This device is intended for indoor use in professional healthcare facilities. This device has no IEC/EN60601-1-2 essential performance. ! Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
Нормативные требования Евразийского Экономического Союза Russia HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171, г. Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677 'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г.
Contact Aruba Main Site https://www.ArubaInstantOn.com Support Site https://www.ArubaInstantOn.com/contact-support/ Aruba Instant On Community https://community.ArubaInstantOn.com North America Telephone 1-800-943-4526 1-408-754-1200 International Telephone https://www.ArubaInstantOn.
