R LCM1511WTV COLOR LCD MONITOR WITH TV TUNER OWNER’S MANUAL Audiovox Specialized Applications, LLC 23319 Cooper Drive Elkhart, IN 46514 800-688-3135 www.asaelectronics.
PACKING Monitor Remote Control Interface Cable 12V Power Cord Batteries: Size AAA x 2 Mounting Hardware Manual WARNING
TABLE OF CONTENTS Page 1 1. LCM Monitor 2 LCD, Tuner Pack, IR Remote Controller 3 2. Feature Function, IR Remote 3 2-1 Power 3 2-2 Input Signal Detection 3 2-3 Contrast/Color/Brightness Adjustment 3 2-4 Volume Adjustment 3 2-5 Audio Mute 4 3. Manual Functions 4 3-1 Key Functions 4 3-2 Volume Control 4 3-3 OSD Icons and Functions Description 4 3-4 Video Adjustments 4 Reference table of OSD Functions and Descriptions 5 4.
Front H G G A B CDE F Rear A. IR Eye B. Menu C. Select D. ADJ- E. ADJ+ F. Power LED G. Speakers H. LCD Panel A B A. VGA Input B. DC 12V IN C D C. A/V D.
LCD, Tuner Pack, IR Remote Control Remote Controller POWER ON/OFF CHANNEL SELECT VOLUME ADJUST +/COLOR COLOR TV/AV MENU MUTE SPKR ON/OFF CONTRAST CONTRAST BRIGHT BRIGHTEN Page 2
2. Feature Function, IR Remote 2-1 Power Pointing the remote towards the IR eye on the LCD, press and hold the POWER On/Off button on the remote controller unit until it turns on the system. Repeat this procedure to turn off system. Power On- The LCD monitor will light up, and the green power light on the front panel will be ON. The OSD (On Screen Display) will show the mode of operation. Power Off- The monitor screen will be dark, the green power light will change to orange.
Press the Mute button to disable audio output. The screen will display “Mute” on upper right corner of the monitor. To cancel mute status, just press Mute key again. The “Mute” message on upper right corner will disappear.
3. Feature Functions by Manual 3-1 Key Functions There are 4 buttons on the monitor which are “Menu”; “Select”; “-“; and “+”. (1) MENU: Pop up & close the OSD (On Screen Display) menu. (2) SELECT: Steps between the function ICONS when OSD menu is on. (3) -: Decreases the adjustment or Pick a selection. (4) +: Increases the adjustment or Pick a selection. NOTE: There are no available functions on the “SELECT” key when the OSD menu is not active.
The screen will display the one that you choose, then use the volume s or t to adjust it. If you take longer than 4 seconds to adjust, the menu display will disappear . The system will reset to s or t Volume.
The Reference table of OSD Functions and Descriptions Mark PWROn/Off Function Keyboard Adjust Brightness (-) (+) Contrast (-) (+) Color (-) (+) Hue (A/V) / Phase (PC) (-)G (-) Volume (-) (+) H. Position (-)L R(+) V. Position (-)Up Down(+) H. Size (-)Narrow Wide(+) V. Size (-)Narrow Wide(+) Expansion (-)Off On(+) Mute Speaker (-)Off On(+) Signal Source Select 1. AV/PC - Auto 2. PC/AV - Auto 3. AV 4. PC Filter (-)Off System (A/V) 1.
4. Feature Functions 4-1 No Signal Detection The monitor will detect signal input automatically. If the signal source is OFF or removed, there is a“ “ icon that will appear and blink on the upper right corner of the screen that means “No Signal Input”. The system will go to power saving mode when there is no signal input for 1 minute. 4-2 Auto Memory Function All of the functions adjustments, will be saved automatically.
Page 6
5. Tuner Functions: (Performed only by IR Remote) 5-1 Power Press and hold the POWER On/Off button on the IR remote controller unit the system turns ON. Repeat this procedure to turn the power off. Power-On: The LCD monitor will light up, and the green LED on the front panel of the monitor will be On. The On Screen Display (OSD) will show the last position where you turned the unit Off. (For example, when you are on CATV Ch.
memory. The screen will display “AUTO” in the lower left corner while the unit is programming. There are two groups of memory. One is for TV and another is for CATV. This function is valid only in TV or CATV mode. NOTE: If you want to interrupt the auto programming mode, just press the Channel s or t button. We recommend you DO NOT interrupt the auto programming mode, because it will not program in all of the channels and some available channels may therefore be missed.
5-4 Input Signal Detection Tuner system will detect a signal if a signal is received in every mode of signal input. If there is no signal, the screen will display “No Signal”. Otherwise, the signal will be displayed showing the mode. 5-5 Channel Selection Use s or t button for channel selection. If you auto-programmed the channels into memory, the s or t button will do channel steps up or down through the memorized channels.
5-9 Audio Mute Press the MUTE button to disable audio output. Screen will display “MUTE” on the upper right corner of the monitor. To cancel mute status, just press the MUTE key again. The “Mute” message on the upper right corner will disappear.
6. Installation of Monitor and Tuner Pack Monitor Rear View VGA Input DC 12V In AUX A/V Interface Cable 12V Power cable Note: Filtering device inside for automotive use. Tuner/Front View Ant. Cable A/V 2 Input A/V 1 Input To VCP/DVD To Ext.
7. Installation Procedure The monitor is furnished with a metal bracket consisting of 8 mounting holes, located in corners of the flange. The mounting holes will accommodate #10 screws. 1) Locate a mounting hole position that will allow a 2 ¼” depth in wall. 2) Determine if there is plumbing, ducting, or electrical wires in the area before drilling and cutting any holes. Relocate if necessary. 3) Use the monitor’s metal frame as a template to drill holes and cut opening.
Page 10
8. Specifications Power Input/ Consumption Audio/Video Input Operating Temperature Storage Temperature Resolution Back Light View Angle L/R View Angle U/D Power Adapter Monitor Dimensions Monitor Weight PC VGA Input Graphics Mode Color Depth Frame Memory On Screen Display (OSD) Power Saving Mode User Setting DC12V ± 10% < 2A A/V input Mini Jack 0° C ~ +50° C -25° C ~ +60° C XGA 1024 (H) x 768 (V) Pixels Cold Cathode Filament Tube (Left, Right) 60° (Up, Down) 45° AC 90 ~ 260V Input, DC 12V, 2.
9.
10.
OR Visit our Website at: www.asaelectronics.
11.
23319 Cooper Drive Elkhart, IN 46514 Phone: 800-688-3135 Fax: (219) 262-5324 Website: www.asaelectronics.
