User manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Menu Tree
- 4 Basic Operation
- 5 Calling
- 5.1 Open the Call List
- 5.2 Incoming Call
- 5.3 Outgoing Call
- 5.3.1 Pre-Dial
- 5.3.2 Post-Dial with Headset Button
- 5.3.3 Dial Using a Pre-programmed Number
- 5.3.4 Dial a Number from the Call list
- 5.3.5 Dial Last Called Number with Headset Button
- 5.3.6 Dial the Sender of a Message
- 5.3.7 Dial a Number from Contacts
- 5.3.8 Dial a Name from the Central Phonebook
- 5.3.9 Dial a Number from the Company Phonebook
- 5.4 During a Call
- 5.4.1 Adjust the Volume during a Call
- 5.4.2 Open Contacts during the Call
- 5.4.3 Open Messaging Menu during a Call
- 5.4.4 Turn the Microphone On or Off during a Call
- 5.4.5 Lock and Unlock the Keypad during a Call
- 5.4.6 Audio Transfer
- 5.4.7 Start a New Call during Conversation
- 5.4.8 Switch between Calls
- 5.4.9 End a Call
- 5.4.10 Transfer a Call
- 5.4.11 Transfer to New Call
- 5.4.12 Conference Call
- 5.4.13 Call Back
- 5.4.14 Send Call Waiting
- 5.4.15 Answering Call Waiting
- 5.4.16 DTMF
- 5.4.17 DECT Info
- 5.4.18 Send Data
- 5.5 Loudspeaking Function
- 5.6 Call Diversion
- 5.7 Emergency Calls
- 6 Messaging
- 6.1 Mini Messaging
- 6.2 Message List
- 6.3 Receive a Message
- 6.3.1 Read a Stored Message
- 6.3.2 Reply to a Message
- 6.3.3 Delete Messages
- 6.3.4 Forward a Message
- 6.3.5 Call the Sender of the Message
- 6.3.6 Call a Number Included in a Message
- 6.3.7 Save Number
- 6.3.8 Message Templates
- 6.3.9 Write and Send a Message
- 6.3.10 Open a Sent Message
- 6.3.11 Send to Another Destination
- 6.3.12 Review Inbox Content while Reading a Message
- 6.4 Receive a Message with Request for Answer
- 6.5 Message Queuing and Message Priority
- 6.6 Message Priority and Call Priority
- 6.7 Interactive Messaging
- 6.8 Message Indication Repetition
- 6.9 Colored Messaging
- 6.10 Decline a Call with a Predefined Message
- 6.11 Answering a Text Message with a Predefined Message
- 6.12 Calling while Reading a Text Message
- 6.13 Mobile Data
- 6.14 Send Data with Bluetooth Barcode Reader
- 6.15 Voicemail
- 7 Alarm Operation
- 8 Menu Operation
- 9 Procedure Call
- 10 System Profiles
- 11 Advanced Functions
- 12 System Handling
- 13 Troubleshooting
- 14 Operation Notice
- 15 Maintenance
- 16 Related Documents
- 17 Document History
- Appendix A: Bluetooth Headset
- Appendix B: Bluetooth Barcode Reader
- Index
12:34
Accept Reject
010
Fire alert in
building A...
TD 92477EN
31 October 2013 / Ver. J
User Manual
Ascom d62 DECT Handset
53
Figure 10. Incoming Invitation Received as a Message
1 Press "Accept".
The handset may accept the invitation autom
a
tically, start in inverted mute and
loudspeaking mode, depending on the configuration of the received invitation.
When the invitation is accepted, the following screen appears (see figure 11). The invitation
can now be deleted or closed by clicking the soft key Delete or Close,
respectively. The call is
not disconnected by clicking these soft keys. The soft key Call is used for re-joining a group
only, see 8.2.8 Re-join a Group on pa
ge 54.
12:34
Call Close
011
Fire alert in
building A...
Delete
Figure 11. Accepted PTT Invitation
2Press and hold
to open the microphone for transmitting. The microphone is
muted again when
is released.
NOTE: In the d62 Messenge handset, the multif
unction button may have also been
configured to act as the
button.
Invitation Received as Message during an Ongoing Call
If a user receives an
invitation during
an ongoing call, the call is disconnected and the PTT
call connected if the following conditions apply:
• The handset is configured to answer invitations automatically
•
The invitation is of higher priority than
the call priority
• The user does not reject the invitation within 10 seconds
When the invitation is received, a warning signal notifies the user before disconnect
ing the
current call in order to connect the PTT call.
Note: Depending on the priority of the invitation
, the ongoing call might be disconnected
immediately or after 10 seconds.