User manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Menu Tree
- 4 Basic Operation
- 5 Calling
- 5.1 Open the Call List
- 5.2 Incoming Call
- 5.3 Outgoing Call
- 5.3.1 Pre-Dial
- 5.3.2 Post-Dial with Headset Button
- 5.3.3 Dial Using a Pre-programmed Number
- 5.3.4 Dial a Number from the Call list
- 5.3.5 Dial Last Called Number with Headset Button
- 5.3.6 Dial the Sender of a Message
- 5.3.7 Dial a Number from Contacts
- 5.3.8 Dial a Name from the Central Phonebook
- 5.3.9 Dial a Number from the Company Phonebook
- 5.4 During a Call
- 5.4.1 Adjust the Volume during a Call
- 5.4.2 Open Contacts during the Call
- 5.4.3 Open Messaging Menu during a Call
- 5.4.4 Turn the Microphone On or Off during a Call
- 5.4.5 Lock and Unlock the Keypad during a Call
- 5.4.6 Audio Transfer
- 5.4.7 Start a New Call during Conversation
- 5.4.8 Switch between Calls
- 5.4.9 End a Call
- 5.4.10 Transfer a Call
- 5.4.11 Transfer to New Call
- 5.4.12 Conference Call
- 5.4.13 Call Back
- 5.4.14 Send Call Waiting
- 5.4.15 Answering Call Waiting
- 5.4.16 DTMF
- 5.4.17 DECT Info
- 5.4.18 Send Data
- 5.5 Loudspeaking Function
- 5.6 Call Diversion
- 5.7 Emergency Calls
- 6 Messaging
- 6.1 Mini Messaging
- 6.2 Message List
- 6.3 Receive a Message
- 6.3.1 Read a Stored Message
- 6.3.2 Reply to a Message
- 6.3.3 Delete Messages
- 6.3.4 Forward a Message
- 6.3.5 Call the Sender of the Message
- 6.3.6 Call a Number Included in a Message
- 6.3.7 Save Number
- 6.3.8 Message Templates
- 6.3.9 Write and Send a Message
- 6.3.10 Open a Sent Message
- 6.3.11 Send to Another Destination
- 6.3.12 Review Inbox Content while Reading a Message
- 6.4 Receive a Message with Request for Answer
- 6.5 Message Queuing and Message Priority
- 6.6 Message Priority and Call Priority
- 6.7 Interactive Messaging
- 6.8 Message Indication Repetition
- 6.9 Colored Messaging
- 6.10 Decline a Call with a Predefined Message
- 6.11 Answering a Text Message with a Predefined Message
- 6.12 Calling while Reading a Text Message
- 6.13 Mobile Data
- 6.14 Send Data with Bluetooth Barcode Reader
- 6.15 Voicemail
- 7 Alarm Operation
- 8 Menu Operation
- 9 Procedure Call
- 10 System Profiles
- 11 Advanced Functions
- 12 System Handling
- 13 Troubleshooting
- 14 Operation Notice
- 15 Maintenance
- 16 Related Documents
- 17 Document History
- Appendix A: Bluetooth Headset
- Appendix B: Bluetooth Barcode Reader
- Index
TD 92477EN
31 October 2013 / Ver. J
User Manual
Ascom d62 DECT Handset
78
LED Error Indications
See also chapter LED Indications during Easy Replacem
ent on page 83.
LED is flashing red, quick flash, (10
0 ms on, 800 ms off)
1) If a third handset, that is another handset than the "old"
(the replaced handset) and
"new" (the replacement handset) handset, is inserted into the charger during Easy
Replacement, this error indication appears. Change to the correct handset.
2) The charger has found that Easy Replacement does not work. Change ba
ck to the "new"
handset.
LED is flashing red, long flash (800 ms on, 100 ms off)
Error during Easy Replacement. Both telephones need to be sent for service
.
Could not encrypt
connection
The parameter "Encryption
Requ
ired" is enabled in the
handset in combination with;
1) Unencrypted ba
se station(s);
and/or,
2) Unsupported base station(s).
1) Disable the "Encryption
R
equired" parameter in
handset; and/or,
2) Enable the encryption in the
b
ase station(s); and/or,
Note: If Ascom’s base station(s)
is used, the
software version
must be 3.1.x or greater.
3) Use supported base
stati
on(s). Ask your supplier.
Not allowed 1) The handset with the shared
ph
one functionality enabled
cannot be logged in due to
another handset using the
extension (that is, User).
2) The extension (User) does not
exists.
3) The password is not correct.
1) Logout the handset using
t
he extension.
2) Make sure that you entered
correct extension. If needed,
contact the
system
administrator.
3) Make sure that you have
entered correct pass
word. Ask
the system administrator if you
have forgot the password.