User's Manual
Table Of Contents
- 1 Introduction
- 2 Description
- 3 Safety Instructions
- 4 IP Security
- 5 Installation of the Base Station
- 5.1 Base Station Cabling
- 5.2 Install the Base Station
- 5.2.1 Fix the Mounting Bracket to a Wall
- 5.2.2 Fix the Mounting Bracket to a Ceiling
- 5.2.3 Fix the Mounting Bracket to a Pole or Beam
- 5.2.4 Use the Cable Ducts for IPBS1
- 5.2.5 Connect External Antennas (only IPBS2 and DB1)
- 5.2.6 Secure the Cable
- 5.2.7 Pinning
- 5.2.8 Connect the Base Station Cables
- 5.2.9 Mount the Base Station
- 5.3 Power the Base Station
- 6 Installation of the IPBL
- 7 Configuration
- 7.1 Requirements
- 7.2 Access the GUI
- 7.3 GUI Web Access
- 7.4 Configure the Mobility Master
- 7.5 Configure the Standby Mobility Master
- 7.6 Configure the Pari Master
- 7.7 Configure the Standby Pari Master
- 7.8 Configure the Master
- 7.9 Configure the Standby Master
- 7.10 Plug and Play Configuration
- 7.11 Configure the Radio
- 7.12 Configure Deployment
- 7.13 Add Users
- 8 Operation
- 8.1 General
- 8.1.1 Name the IPBS/IPBL
- 8.1.2 Change User Name and Password
- 8.1.3 Centralized Management of Administrator/Auditor Accounts Using Kerberos
- 8.1.4 Configure Automatic Firmware Update
- 8.1.5 Configure the NTP Settings
- 8.1.6 Configure Logging
- 8.1.7 Configure the HTTP settings
- 8.1.8 Configure the HTTP Client settings
- 8.1.9 SNMP
- 8.1.10 Certificates
- 8.1.11 License
- 8.2 LAN
- 8.3 IP
- 8.4 LDAP
- 8.5 DECT
- 8.5.1 Change System Name and Password
- 8.5.2 Set Subscription Method
- 8.5.3 Configure Authentication Code
- 8.5.4 Select Tones
- 8.5.5 Set Default Language
- 8.5.6 Set Frequency Band
- 8.5.7 Enable Carriers
- 8.5.8 Local R-Key Handling
- 8.5.9 No Transfer on Hangup
- 8.5.10 Configure Coder
- 8.5.11 Secure RTP
- 8.5.12 Configure Supplementary Services
- 8.5.13 Select Mode
- 8.5.14 Set Master Id
- 8.5.15 Enable PARI Function
- 8.5.16 Configure Gatekeeper
- 8.5.17 Registration for Anonymous Devices
- 8.5.18 Select Mobility Master Mode
- 8.5.19 Connect Mobilty Master to other Mobility Master(s)
- 8.5.20 Disconnect Mobilty Master from other Mobility Master(s)
- 8.5.21 Connect Master to a Mobility Master
- 8.5.22 Enable the Radio
- 8.5.23 Enter IP Address to the PARI Master and the Standby PARI Master
- 8.5.24 Multiple Radio Configuration
- 8.5.25 PARI
- 8.5.26 SARI
- 8.5.27 Configure Air Synchronization
- 8.6 VoIP
- 8.7 UNITE
- 8.8 Import and Export a Central Phonebook
- 8.9 Users
- 8.10 Device Overview
- 8.11 DECT Sync
- 8.12 Traffic
- 8.13 Gateway
- 8.14 Backup
- 8.15 Software Upgrade
- 8.15.1 Before Upgrading
- 8.15.2 Upgrading Sequence
- 8.15.3 IPBS/IPBL Upgrade
- 8.15.4 Configuration After Updating the Firmware From Software Version 2.x.x to Later
- 8.15.5 Configuration After Updating the Firmware From Software Version 3.x.x to Later
- 8.15.6 System Upgrade from Software Version 4.x.x to 5.0.x
- 8.16 System Downgrade from software version 5.0.x to 2.x.x, from 4.x.x to 2.x.x and from 3.x.x to 2.x.x
- 8.17 System Downgrade from software version 5.0.x to 3.x.x and 4.x.x to 3.x.x
- 8.18 Update
- 8.19 System Upgrade in System with Mobility Masters
- 8.20 Replacing Master Hardware in Multiple Master System
- 8.21 Diagnostics
- 8.22 Reset
- 8.23 Reset Using the Reset Button
- 8.1 General
- 9 Commissioning
- 10 Troubleshooting
- 11 Related Documents
- Document History
- Appendix A: How to Use the Update Server
- Appendix B: RFP Power Consumption
- Appendix C: Local R-Key Handling
- Appendix D: Database Maintenance
- Appendix E: Load Balancing
- Appendix F: Update Script for Configuration of Kerberos Clients
- Appendix G: Install Certificate in the Web Browser
TD 92579EN
15 February 2012 / Ver. H
Installation and Operation Manual
IP-DECT Base Station & IP-DECT Gateway (software version 5.0.x)
150
mod cmd UP1 times [/allow <hours>] [/initial <minutes>]
The times command will check the current time against <hours>. If it does not match this
restriction, any further processing of the command file is cancelled. <hours> is a comma
separated list of hours. Only those hours listed are considered valid times for execution of
the command file.
mod cmd UP1 times /allow 12,23,1,2,3,4
The command above allows command executions only between 12:00 and 12:59 and
23:00 and 4:59 local time (on a 24h clock). Note that if the device has no time set, all
command executions will be cancelled.
If the /initial parameter is set, the no commands will be executed within the first
<minutes> minutes after the device has been booted. This is done to avoid firmware
download and flashing when installing devices.
mod cmd UP1 times /allow 12,23,1,2,3,4 /initial 6
The command above suppresses any command file processing within the first six minutes
after each boot of the device. If /initial is set, new devices (or those that have been reset to
factory settings), the command file will be retrieved even if it normally would be
suppressed by the /allow parameter. This allows new devices to retrieve a site specific
standard configuration quickly.
A.1.5 Setting the UP0 Parameters
To perform a firmware update, use the following command:
mod cmd UP0 prot <url> <final-command> <build-serial>
The command above downloads the new firmware from <url> and flash it to the device,
then <final-command> is executed.
The IPBSs maintain an internal variable UPDATE/PROT which is initially (or when the device
is reset to factory settings) empty. The prot command will compare the <build-serial>
parameter with the UPDATE/PROT variable. If it is equal, no firmware will be loaded or
flashed. If there is no UPDATE/PROT yet (like for a new device), <build-serial> is compared
against the build number of the current firmware. After a successful download, UPDATE/
PROT is set to <build-serial>. Note that <build-serial> is not checked against the firmware
version actually loaded. It is your responsibility to keep this consistent.
If <url> ends with a slash ('/'), then a default firmware filename is added to the URL
depending on the type of the device.
mod cmd UP0 prot http://192.168.0.10/firm/ ireset 5.0.0
The command above determines if firmware 5.0.0 is already installed. If not, new
firmware will be downloaded from the following location depending on type of device:
IPBS1: http://192.168.0.10/firm/ipbs.bin
IPBS2: http://192.168.0.10/firm/ipbs2.bin
IPBL: http://192.168.0.10/firm/ipbl.bin
The UPDATE/PROT variable will be set to 5.0.0 and the device will be reset as soon as it is
idle.
Similar to the prot command, the boot command will update the boot code.
Firmware filename
IPBS1 ipbs.bin
IPBS2 ipbs2.bin
IPBL ipbl.bin