User's Manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Safety Instructions
- 3 Descriptions
- 4 Basic Operation
- 5 Menu Tree
- 6 Calling
- 6.1 Incomming Call
- 6.2 Outgoing Call
- 6.2.1 Pre-Dial
- 6.2.2 Post-Dial
- 6.2.3 Dial Using a Pre-programmed Hot/Soft/Navigation Key or Multifunction Button
- 6.2.4 Dial a Number from the Call list
- 6.2.5 Dial the Sender of a Message
- 6.2.6 Dial a Number from the Local Phonebook
- 6.2.7 Dial a Number from the Company Phonebook
- 6.2.8 Dial a Name from the Central Phonebook
- 6.3 During a Call
- 6.3.1 Adjust the Volume during a Call
- 6.3.2 Open Contacts during the Call
- 6.3.3 Turn the Microphone on/off during a Call
- 6.3.4 Start a New Call during Conversation
- 6.3.5 Switch between Calls
- 6.3.6 End a Call
- 6.3.7 Transfer a Call
- 6.3.8 Transfer to new Call
- 6.3.9 Conference Call
- 6.3.10 Call Back
- 6.3.11 Call Waiting
- 6.3.12 DTMF
- 6.3.13 DECT Info
- 6.4 Loudspeaking Function
- 6.5 Call Diversion
- 6.6 Additional Call Services
- 7 Menu Operations
- 8 Enhanced Messaging
- 9 Advanced Functions
- 10 Operation Notice
- 11 System Handling
- 12 Maintenance
- 13 Troubleshooting
- 14 Related Documents
- 15 Document History
- Index
PRELIMINARY
TD 92643GB
30 September 2010 / Ver. PA4
User Manual
Cordless Telephone 3740 for Avaya
39
2 Change the priority if needed by selecting "Up" or "Down". The priority will be saved
when "Back" is selected.
7.1.3 In Charger Actions when in Call
It is possible to end a call, or turn on the loudspeaker by putting the telephone in a charger
during a call.
1 Select "In charger".
2 Select "Call behavior".
3 Select one of the following:
• No action - no action will be performed when the telephone is placed in charger
duringa a call.
• Loudspeaking - the loudspeaker will be turned on when the telephone is placed in
charger during a call. The loudspeaker will be turned off when removing the
telephone from charger.
• End call - the ongoing call will be disconnected when the telephone is placed in
charger.
7.1.4 In Charger Actions when Not in Call
It is possible to determine what to happend when a telephone is placed in a charger. Note
that no call is established.
Redirect Calls and Messages when Placed in Charger
Calls can be redirected to another extension when the telephone is placed in a charger. In
addition, message absence is also enabled when calls is redirected. When an application/
system sends a message to a telephone, it will receive an indication that the telephone is
absent. If a telephone is absent, the application/system determines if the message shall be
sent to the telephone or not, or redirected to another telephone.
Note: If a message is sent from a telephone, it will not receive an indication that the
recipient is absent.
The function is automatically cancelled when the telephone is removed from the charger.
Note: This function must be programmed in the PBX to be able to redirect calls/messages.
1 Select “In charger”.
2 Select "Other actions"
3 Select “Redirect”.
Switch off While Charging
When the cordless telephone is placed in the charger it can be switched off while it is
charging. When it is removed from the charger it will switch on again.
1 Select “In charger”.
2 Select "Other actions"
3 Select “Switch off”.