User's Manual
Table Of Contents
- 1 Introduction
- 2 IP Security
- 3 Configuration
- 3.1 Requirements
- 3.2 Access the GUI
- 3.3 GUI Web Access
- 3.4 Configure the Mobility Master
- 3.5 Configure the Standby Mobility Master
- 3.6 Configure the Pari Master
- 3.7 Configure the Standby Pari Master
- 3.8 Configure the Master
- 3.9 Configure the Standby Master
- 3.10 Plug and Play Configuration
- 3.11 Configure the Radio
- 3.12 Configure Deployment
- 3.13 Add Users
- 4 Operation
- 4.1.1 Name the IPBS and IPBL
- 4.1.2 Change User Name and Password
- 4.1.3 Centralized Management of Administrator and Auditor Accounts Using Kerberos
- 4.1.4 Configure the NTP Settings
- 4.1.5 Certificates
- 4.1.6 License
- 4.2.1 Set DHCP Mode
- 4.2.2 Set a Static IP Address
- 4.2.3 Dynamic IP address via DHCP
- 4.2.4 Link
- 4.2.5 Configure VLAN
- 4.2.6 View LAN Statistics
- 4.2.7 Enable RSTP (only for IPBL)
- 4.2.8 Deactivate LAN Port (only for IPBL)
- 4.3.1 Configure IP Settings
- 4.3.2 Routing
- 4.4.1 Configure LDAP Server
- 4.4.2 Check LDAP Server Status
- 4.4.3 Configure LDAP Replicator
- 4.4.4 Check LDAP Replicator Status
- 4.4.5 Expert tool
- 4.5.1 Change System Name and Password
- 4.5.2 Set Subscription Method
- 4.5.3 Configure Authentication Code
- 4.5.4 Select Tones
- 4.5.5 Set Default Language
- 4.5.6 Set Frequency Band
- 4.5.7 Enable Carriers
- 4.5.8 Local R-Key Handling
- 4.5.9 No Transfer on Hangup
- 4.5.10 No On-Hold Display
- 4.5.11 Display Original Called
- 4.5.12 Early Encryption
- 4.5.13 Configure Coder
- 4.5.14 Secure RTP
- 4.5.15 Configure Supplementary Services
- 4.5.16 Select Mode
- 4.5.17 Set Master Id
- 4.5.18 Enable PARI Function
- 4.5.19 Set Region Code
- 4.5.20 Configure Gatekeeper
- 4.5.21 Registration for Anonymous Devices
- 4.5.22 Conferencing Unit
- 4.5.23 Select Crypto Master Mode
- 4.5.24 Select Mobility Master Mode
- 4.5.25 Connect Mobility Master to other Mobility Master(s)
- 4.5.26 Disconnect Mobility Master from other Mobility Master(s)
- 4.5.27 Connect Mobility Master to a Crypto Master
- 4.5.28 Connect Master to a Mobility Master
- 4.5.29 Enable the Radio
- 4.5.30 Enter IP Address to the PARI Master and the Standby PARI Master
- 4.5.31 Multiple Radio Configuration
- 4.5.32 PARI
- 4.5.33 SARI
- 4.5.34 Configure Air Synchronization
- 4.6.1 Add instance id to the user registration with the IP-PBX
- 4.6.2 IP-PBX supports redirection of registration when registered to alternative proxy
- 4.6.3 Use local contact port as source port for TCP and TLS connections
- 4.6.4 Session Timer (initial value)
- 4.7.1 Configure Messaging
- 4.7.2 Device Management
- 4.7.3 Service Discovery
- 4.7.4 Send Status Log
- 4.7.5 Module Fault List
- 4.8.1 Configure Automatic Firmware Update
- 4.8.2 Configure Logging
- 4.8.3 Configure the HTTP settings
- 4.8.4 Configure the HTTP Client settings
- 4.8.5 SNMP
- 4.8.6 Phonebook
- 4.8.7 Configure IP-DECT to Connect to a Presence System Using ICP
- 4.9.1 Show all Registered Users in the IP-DECT System
- 4.9.2 Search for User Information
- 4.9.3 Add a User
- 4.9.4 Add a User Administrator
- 4.9.5 Export the Users to a csv file
- 4.9.6 Show Anonymous
- 4.10.1 Radios
- 4.10.2 RFPs
- 4.10.3 Sync Ring
- 4.10.4 Sync Ports
- 4.10.5 Air Sync
- 4.10.6 Sync Lost Counter in IPBS
- 4.11.1 Air Sync Overview
- 4.11.2 Disturbances
- 4.11.3 Status
- 4.12.1 Display All Ongoing Calls in the System
- 4.12.2 Display Calls
- 4.12.3 Handover
- 4.13.1 General
- 4.13.2 Interfaces
- 4.13.3 SIP Interfaces
- 4.13.4 Gatekeeper Interfaces
- 4.13.5 Routes – Configuration
- 4.13.6 Show Active Calls
- 4.15.1 Before Upgrading
- 4.15.2 Upgrading Sequence
- 4.15.3 Software Upgrade from 2.X.X
- 4.15.4 Software Upgrade
- 4.15.5 Configuration After Updating the Firmware From Software Version 2.X.X to Later
- 4.15.6 Configuration After Updating the Firmware From Software Version 3.X.X to Later
- 4.21.1 Update Configuration
- 4.21.2 Update Firmware
- 4.21.3 Update the Boot File
- 4.21.4 Update the RFPs
- 4.26.1 Logging
- 4.26.2 Tracing
- 4.26.3 Alarms
- 4.26.4 Events
- 4.26.5 Performance
- 4.26.6 Config Show
- 4.26.7 Ping
- 4.26.8 Traceroute
- 4.26.9 Environment
- 4.26.10 RFP Scan
- 4.26.11 Service Report
- 4.27.1 Idle Reset
- 4.27.2 Immediate Reset
- 4.27.3 TFTP Mode
- 4.27.4 Boot
- 5 Commissioning
- 6 Troubleshooting
- 7 Related Documents
- Document History
- Appendix A: How to Configure and Use the Update Server
- Appendix B: Local R-Key Handling
- Appendix C: Database Maintenance
- Appendix D: Load Balancing
- Appendix E: Update Script for Configuration of Kerberos Clients
- Appendix F: Install Certificate in the Web Browser
- Appendix G: Used IP Ports
- Appendix H: Configure DHCP Options
TD 92579EN
15 October 2014 / Ver. M
Installation and Operation Manual
IP-DECT Base Station & IP-DECT Gateway (software version 7.2.X)
58
• Display Original Called is enabled: The extension number or name of handset B will be
shown in handset D.
• Display Original Called is no
t enabled: The extension number or name of handset C
will be shown in handset D.
Note: In both cases the extension number or name of
handset A will be shown as well.
To enable Original Called Display
, do as follows:
1 Select DECT > System.
NOTE: To access the System tab, the Master
mode has to be activated, see
4.5.16 Select Mode on page 62.
2 To enable, select the Display Original Called check box.
3 Click "OK".
4.5.12 Early Encryption
With this option enabled the early encryption featur
e will be activated in the IP-DECT
system.
Note: Activating early encryption will cause a restart of all RFPs.
Note: For the early encryption feature to function in the system, the DECT handset must
also support early encryption.
Note: Handsets already registered will continue to function without early encryption.
Note: Only the handsets registered after enabling the early encryption feature will have
support for this feature.
For more information on early encryption, see about Enhanced DECT Security in the
System Description documentation for IP-DECT.
1 Select DECT > System.
NOTE: To access the System tab, the Master
mode has to be activated, see
4.5.16 Select Mode on page 62.
2 To enable, select the Ear
ly Encryption check box.
Note: To access the Early E
ncryption check box, the Pari Master mode has to be
activated, see 4.5.18 Enable PARI Function on page 63.
3 Click "OK".
When using IPBL and the early encryption feature is enabled:
The RFPs will startup
only if they support this feature.
4 In a system with several PARI Masters, it
is recommended to repeat step 1 to 3 for
all PARI Master.
Note: It is possible to have a system w
ith different Pari domains where early
encryption is enabled in some and disabled in other. However, all RFPs and IPBSs
must have software support for early encryption even though it is not enabled.
5 To enable the early encryption feature in a
system with Mobility Master(s), connect
the Mobility Master(s) to a Crypto Master, see 4.5.27 Connect Mobility Master to a
Crypto Master on page 68.
6 To view a list of DECT handsets where early encryption is
in use: Select Users >
Users and then click "Show". Those DECT handsets where early encryption is in use
is indicated with a dot in the column EE (Early Encryption).