User's Manual
Table Of Contents
- 1 Introduction
- 2 Descriptions
- 3 Basic Operation
- 3.1 Switch the Handset On/Off
- 3.2 The Call List
- 3.3 Calling
- 3.4 Start a New Call during Conversation
- 3.5 Transfer a Call/Retrieve the Call
- 3.6 “Blind” Transfer
- 3.7 Turn Off Alert Signals at an Incoming Call
- 3.8 Put a Call on Hold/Retrieve the Call
- 3.9 Turn the Mute Mode Off/On during a Call
- 3.10 Loudspeaking Function
- 3.11 Increase/Decrease the Speaker Volume during a Call
- 3.12 Turn Audible Signals On/Off
- 3.13 Lock/Unlock the Keypad
- 3.14 Lock/Unlock the Handset
- 4 Messaging
- 5 Alarm Operation
- 6 Navigate the Menu
- 7 Menu Tree
- 8 Menu Operation
- 8.1 Contacts
- 8.2 Messages
- 8.3 Call List
- 8.4 Services
- 8.5 Settings
- 8.5.1 Change the Volume
- 8.5.2 Change the Ring Signal
- 8.5.3 Vibrator On/Off
- 8.5.4 Key Beep On/Off
- 8.5.5 Deactivate/Activate No-movement alarm
- 8.5.6 Deactivate/Activate Man-down alarm
- 8.5.7 Edit a Soft key
- 8.5.8 Edit a Hot key
- 8.5.9 Select Language
- 8.5.10 Change Text Size in Messages
- 8.5.11 Lock the Handset Manually
- 8.5.12 Change the Lock Code
- 8.5.13 Time and Date Settings
- 8.5.14 Turn On/Off Automatic Keypad Lock
- 8.5.15 Enable/Disable Quick Answer
- 8.5.16 Set New Messages to be Displayed Upside down
- 8.5.17 Set Owner ID
- 8.5.18 Select System
- 8.5.19 System Information
- 8.6 Profiles
- 8.6.1 Change Profiles
- 8.6.2 Change Profile Settings
- 8.6.3 Set the Profile to Absent On/Off
- 8.6.4 Choose the Profile’s Answering method
- 8.6.5 Set the Profile to Divert incoming Calls to another telephone number
- 8.6.6 Preset the telephone numbers for the Diversions alternatives
- 8.6.7 Customizing the Profiles Menu
- 9 Advanced Functions
- 10 Operation Notice
- 11 Maintenance
- 12 Related Documents
- Appendix A: Programming the Handset
- Index
PRELIMINARY
TD 92319GB
2005-10-20/ Ver. PA11
User Manual
i75 Cordless IP Handset
17
action can be sending a message back to the application, and/or dialling a specific number
etc.
An IM is indicated and viewed the same way as an ordinary message, see 4.2.1 Receive a
Message on page 15, but the “Interactive message” icon is added in front of the message.
It is saved along with other messages in the message list.
Interactive Messaging is a system dependent function.
4.5.1 Interactive Messages with Function Keys
If there are function keys specified in an Interactive Message, they will be mapped to the
Soft keys and the alphanumeric keys. Function Key ID (A) will be mapped to the left Soft
key, Function Key ID (B) will be mapped to the middle Soft key, and Function Key ID (C) will
be mapped to the right Soft key. Function key IDs (0)–(9) will be mapped to the
corresponding alphanumeric keys.
4.5.2 Interactive Messages without Function Keys
Open an Interactive Message the same way as an ordinary message. If the IM gives you
several options, mark the one you want and press “Select”. If the selected option requests
input, enter the information needed and press “Select”. A press on the middle soft key
will change to digit input mode to facilitate entering numbers.
4.6 Voice Mail
4.6.1 Receive a Voice Mail
A ring signal and the “New voice mail” icon in the display indicate that a new voice mail
has arrived. You can listen to voice mail by selecting the “Voice mail” entry in the
“Messages” menu.
4.7 Mobile Data
4.7.1 Send Mobile Data
It is possible to send user entered data from the handset by pressing a pre-programmed
Hot key or Soft key, or selecting a Service. Mobile data can be used for opening a door,
starting/stopping a machine etc. The data can either be predefined, or entered after the
Hot key/Soft key is pressed or Service is selected.
The data can be predefined when programming the Soft/Hot key or Service, see 8.5.7 Edit
a Soft key on page 33 or 8.4.3 Edit a Service on page 31.
4.7.2 Send Mobile Data with a Prefix
Mobile data with a prefix is sent from the handset by entering data and then pressing a
pre-programmed Hot key or Soft key or select a Service. Mobile data with prefix can be
used to send information to an application in the system. The prefix is predefined by the
user when programming the Hot/Soft key or Service, see
8.5.7 Edit a Soft key on page 33
or 8.4.3 Edit a Service on page 31.