User manual
Table Of Contents
- 1. Introduction
- 2. Pre-Installation
- 3. Programming the VoWiFi Handset
- 4. Installation of VoWiFi Handsets
- 5. Maintenance
- 5.1 Handset
- 5.1.1 Configure Spare Handsets without a Number in Large Systems
- 5.1.2 Upgrade Handset Software
- 5.1.3 Upgrade Software OTA via TFTP
- 5.1.4 Upgrade Software via PDM
- 5.1.5 Upgrade Software Over the Air (OTA) via Centralized Device Management (IMS3)
- 5.1.6 Recapture the Earlier Software
- 5.1.7 Upgrade Handset Functionality using License
- 5.1.8 Perform a Factory reset
- 5.2 Replacement of Handsets
- 5.3 Change Number of a Handset
- 5.4 Update Parameters via IMS3
- 5.5 Perform a Security Upgrade via IMS3
- 5.6 Upgrade the Template
- 5.7 Create a Configuration Backup
- 5.1 Handset
- 6. Handset Configuration
- 6.1 Select Network
- 6.2 IP Address Settings
- 6.3 Network Settings
- 6.4 Security Settings
- 6.5 Handset Settings
- 6.5.1 Automatic key lock
- 6.5.2 Phone lock
- 6.5.3 Audio adjustment
- 6.5.4 Headset Configuration
- 6.5.5 In Charger Behavior
- 6.5.6 Configure Profiles
- 6.5.7 Hide Missed Call Window
- 6.5.8 Battery Warning
- 6.5.9 Shared Phone
- 6.5.10 Prevent Handset Switch off
- 6.5.11 Uploadable Language
- 6.5.12 Select Default Language
- 6.5.13 Short cuts
- 6.5.14 Soft Key Functions During Call
- 6.5.15 Import Contacts
- 6.5.16 Company Phonebook
- 6.5.17 Central Phonebook
- 6.6 Messaging and Alarm
- 6.7 Messaging Settings
- 6.8 Alarm Settings
- 6.9 Telephony
- 6.9.1 Endpoint ID and Endpoint number
- 6.9.2 VoIP Protocol
- 6.9.3 Codec
- 6.9.4 Offer Secure RTP
- 6.9.5 Internal Call Number Length
- 6.9.6 Emergency Number
- 6.9.7 Voice Mail Number
- 6.9.8 Message Centre Number
- 6.9.9 Max number of Call Completions
- 6.9.10 Dial Pause Time
- 6.9.11 Direct off Hook from Charger
- 6.9.12 Replace Call Rejected with User Busy
- 6.9.13 Busy on 1 / Disable call waiting
- 6.9.14 Calling Line Restriction
- 6.10 Regional Settings
- 6.11 Display
- 6.12 Menu Operation
- 6.13 Push-To-Talk (PTT) Group Call
- 6.14 Presence Management
- 6.15 Location
- 7. Use Handset to Verify the VoWiFi System Deployment
- 8. Handset Internal Web Administration Page
- 9. Administration
- 10. Troubleshooting
- 11. Related Documents
- 12. Document History
- Appendix A: Working with Templates
- Index
- Contents
TD 92675EN
20 June 2012 / Ver. E
Configuration Manual
Ascom i62 VoWiFi Handset
13
4. Installation of VoWiFi
14 In the Numbers tab, right-click the handset’s number and select “Edit certificates“. An
Edit certificate window opens.
15 In the Root ta
b and Client tab, click “Edit“ and select the certificates to import. Click
“Close“.
16 In the Numbers tab, right-click the handset’s num
ber and select “Edit parameters“.
17 Select “Network X“ (X represents
A, B, C, or D).
18 In the Security mode drop-
down list, select “EAP-TLS“.
19 In the EAP cli
ent certificate drop-down list, select the client certificate to be used.
Click “OK“.
20 Remove the handset when synchronization is finished.
Repeat the steps 11-13, 20 (if needed, perfor
m the steps
14-19) for all handsets.
4.3 Installation using the Handset’s Admin Menu
It is possible to install a handset using its Admin menu. This is useful when no PDM/IMS3 is
available and the handset needs to be installed quickly.
NOTE: It is only possible to configure the basic settings vi
a the Admin menu.
1 There are two options to access the Admin menu:
• If the handset has been factory reset or not been configured; in idle m
ode, enter
40022.
• If the handset has been configured; press “Menu“, sel
ect “Settings“ and enter
40022.
2 Set the following parameters:
• Network settings
1
(located under Network setup)
• VoIP settings
2
(located under VoIP)
• Unite settings
3
(if any) (located under Unite)
• Syslog settings
4
(if any) (located under Syslog)
4.4 Configure a Handset with a Template
It is possible to select a handset in the PDM and directly change one or more configuration
parameters. By using a template, the same configuration can easily be applied to many
handsets simultaneously. Templates are also an efficient way to give good control over
which changes that are applied to each handset.
Templates enables configuration of all aspects of a handset from sound volume to keypad
short cuts.
Your supplier can provide example templates for different PBX:s. The handset will have full
functionality towards the PBX even without such a template. By using such a template,
though, the handset will be customized for that PBX with menu options for PBX specific
functions.
1. All required system settings for the WLAN. For example SSID and Security mode
2. VoIP protocol, Gatekeeper IP address or SIP proxy IP address used to access the PBX.
3. IP address and password (if any)
to the IMS3.
4. The parameter “Syslog“ must be enabled in order to set the “Syslog IP addre
ss“.