User manual
Table Of Contents
- 1. Introduction
- 2. Pre-Installation
- 3. Programming the VoWiFi Handset
- 4. Installation of VoWiFi Handsets
- 5. Maintenance
- 5.1 Handset
- 5.1.1 Configure Spare Handsets without a Number in Large Systems
- 5.1.2 Upgrade Handset Software
- 5.1.3 Upgrade Software OTA via TFTP
- 5.1.4 Upgrade Software via PDM
- 5.1.5 Upgrade Software Over the Air (OTA) via Centralized Device Management (IMS3)
- 5.1.6 Recapture the Earlier Software
- 5.1.7 Upgrade Handset Functionality using License
- 5.1.8 Perform a Factory reset
- 5.2 Replacement of Handsets
- 5.3 Change Number of a Handset
- 5.4 Update Parameters via IMS3
- 5.5 Perform a Security Upgrade via IMS3
- 5.6 Upgrade the Template
- 5.7 Create a Configuration Backup
- 5.1 Handset
- 6. Handset Configuration
- 6.1 Select Network
- 6.2 IP Address Settings
- 6.3 Network Settings
- 6.4 Security Settings
- 6.5 Handset Settings
- 6.5.1 Automatic key lock
- 6.5.2 Phone lock
- 6.5.3 Audio adjustment
- 6.5.4 Headset Configuration
- 6.5.5 In Charger Behavior
- 6.5.6 Configure Profiles
- 6.5.7 Hide Missed Call Window
- 6.5.8 Battery Warning
- 6.5.9 Shared Phone
- 6.5.10 Prevent Handset Switch off
- 6.5.11 Uploadable Language
- 6.5.12 Select Default Language
- 6.5.13 Short cuts
- 6.5.14 Soft Key Functions During Call
- 6.5.15 Import Contacts
- 6.5.16 Company Phonebook
- 6.5.17 Central Phonebook
- 6.6 Messaging and Alarm
- 6.7 Messaging Settings
- 6.8 Alarm Settings
- 6.9 Telephony
- 6.9.1 Endpoint ID and Endpoint number
- 6.9.2 VoIP Protocol
- 6.9.3 Codec
- 6.9.4 Offer Secure RTP
- 6.9.5 Internal Call Number Length
- 6.9.6 Emergency Number
- 6.9.7 Voice Mail Number
- 6.9.8 Message Centre Number
- 6.9.9 Max number of Call Completions
- 6.9.10 Dial Pause Time
- 6.9.11 Direct off Hook from Charger
- 6.9.12 Replace Call Rejected with User Busy
- 6.9.13 Busy on 1 / Disable call waiting
- 6.9.14 Calling Line Restriction
- 6.10 Regional Settings
- 6.11 Display
- 6.12 Menu Operation
- 6.13 Push-To-Talk (PTT) Group Call
- 6.14 Presence Management
- 6.15 Location
- 7. Use Handset to Verify the VoWiFi System Deployment
- 8. Handset Internal Web Administration Page
- 9. Administration
- 10. Troubleshooting
- 11. Related Documents
- 12. Document History
- Appendix A: Working with Templates
- Index
- Contents
TD 92675EN
20 June 2012 / Ver. E
Configuration Manual
Ascom i62 VoWiFi Handset
23
5. Maintenance
4 Enter the Number and leave the password blank. Press “Login“.
The spare handset is automatically updated from the IMS3 and might be restarted
dependi
ng on the changed settings. The last stored settings for the broken handset in the
IMS3 has been transferred to the spare handset.
Replace and Move Licenses in IMS3
The broken handset and the spare handset do not have
the same device t
ype and/or have
the same functionality license.
In order to move the licenses to the spare handset, it must be an unlicensed Talker. To check
that the handset is unlicensed, press *#34# in idle mode and select “License“. Only i62
Talker must be displayed here.
1 Make sure that the broken handset is saved in the Device Manager (indicated by a
in the Saved column. If not, in the Numbers tab, right-click the broken handset
and select “Save“.
2 Switch off the broken handset to make it offline in the Device
Manager.
3 Take an unlicensed spare handset (Talker) prepared with the
network settings
(including the IP-address to the IMS3).
4 Enter the number and leave the password blank. Press “Login”. The handset is now
online in the
Device Manager.
5 Make sure that the spare handset is saved in the Device Manager (indicated by a
in the Saved column. If not, in the Numbers tab, right-click the spare handset and
select “Save“.
6 Switch off the spare handset to make it offline in the De
vice Manager.
7 Switch on the broken handset to make it online in the Device Manager.
8 I
n the Device Manager, select the “Licenses“ tab.
9 Right-click the broken handset and select “Move license...“.
10 In the Move license window, select the Talker that should receive the license. Press
“OK
“.
11
The broken handset restarts and has now become a Talker. Switch
off the broken
handset to make it offline in the Device Manager.
12 Switch on the spare handset to make it online in the Device Manager.
13 I
n the Device Manager, select the “Licenses“ tab. Right-click the spar
e handset and
select “Refresh“.
The spare handset is automatically updated from the IMS3 and restarted. The last stored
settings a
nd licenses for the broken handset in the IMS3 has been transferred to the spare
handset.
5.2.3 Replacement of the Handset with PDM a
nd
IMS3
If the spare handset to be used must be factory reset or no network templa
te has been
applied, a PDM is needed to apply the network template to the spare handset. When the
network template is added, the handset can log on to the Device Manager.
There are two different replacement procedures as follows:
• If the broken handset and the spare handset have the same device type and
functionality license, see Replace without Move Licenses using PDM and
IMS3.
• If the broken handset and the spare handset have not the same device type and/or
functionality license. The
license must be moved to the spare handset, see Replace and
Move License using PDM and IMS3 on page 24.