User manual
Table Of Contents
- 1. Introduction
- 2. Pre-Installation
- 3. Programming the VoWiFi Handset
- 4. Installation of VoWiFi Handsets
- 5. Maintenance
- 5.1 Handset
- 5.1.1 Configure Spare Handsets without a Number in Large Systems
- 5.1.2 Upgrade Handset Software
- 5.1.3 Upgrade Software OTA via TFTP
- 5.1.4 Upgrade Software via PDM
- 5.1.5 Upgrade Software Over the Air (OTA) via Centralized Device Management (IMS3)
- 5.1.6 Recapture the Earlier Software
- 5.1.7 Upgrade Handset Functionality using License
- 5.1.8 Perform a Factory reset
- 5.2 Replacement of Handsets
- 5.3 Change Number of a Handset
- 5.4 Update Parameters via IMS3
- 5.5 Perform a Security Upgrade via IMS3
- 5.6 Upgrade the Template
- 5.7 Create a Configuration Backup
- 5.1 Handset
- 6. Handset Configuration
- 6.1 Select Network
- 6.2 IP Address Settings
- 6.3 Network Settings
- 6.4 Security Settings
- 6.5 Handset Settings
- 6.5.1 Automatic key lock
- 6.5.2 Phone lock
- 6.5.3 Audio adjustment
- 6.5.4 Headset Configuration
- 6.5.5 In Charger Behavior
- 6.5.6 Configure Profiles
- 6.5.7 Hide Missed Call Window
- 6.5.8 Battery Warning
- 6.5.9 Shared Phone
- 6.5.10 Prevent Handset Switch off
- 6.5.11 Uploadable Language
- 6.5.12 Select Default Language
- 6.5.13 Short cuts
- 6.5.14 Soft Key Functions During Call
- 6.5.15 Import Contacts
- 6.5.16 Company Phonebook
- 6.5.17 Central Phonebook
- 6.6 Messaging and Alarm
- 6.7 Messaging Settings
- 6.8 Alarm Settings
- 6.9 Telephony
- 6.9.1 Endpoint ID and Endpoint number
- 6.9.2 VoIP Protocol
- 6.9.3 Codec
- 6.9.4 Offer Secure RTP
- 6.9.5 Internal Call Number Length
- 6.9.6 Emergency Number
- 6.9.7 Voice Mail Number
- 6.9.8 Message Centre Number
- 6.9.9 Max number of Call Completions
- 6.9.10 Dial Pause Time
- 6.9.11 Direct off Hook from Charger
- 6.9.12 Replace Call Rejected with User Busy
- 6.9.13 Busy on 1 / Disable call waiting
- 6.9.14 Calling Line Restriction
- 6.10 Regional Settings
- 6.11 Display
- 6.12 Menu Operation
- 6.13 Push-To-Talk (PTT) Group Call
- 6.14 Presence Management
- 6.15 Location
- 7. Use Handset to Verify the VoWiFi System Deployment
- 8. Handset Internal Web Administration Page
- 9. Administration
- 10. Troubleshooting
- 11. Related Documents
- 12. Document History
- Appendix A: Working with Templates
- Index
- Contents
TD 92675EN
20 June 2012 / Ver. E
Configuration Manual
Ascom i62 VoWiFi Handset
24
5. Maintenance
Replace without Move Licenses using PDM and IMS3
Both the broken handset and the spare handset must be
of the same device type and have
same functionality license.
1 In the handset, press *#34# in idle mode and sel
ect “License“ to check that both
handsets have same device type and licenses.
2 Make sure that the broken handset is saved in the Device Manager (indicated by a
in the Saved column. If not, in the Numbers tab, right-click the broken handset
and select “Save“.
3 Switch off the broken handset to make it offline.
If the spare handset is not prepared with the basi
c network
settings, also perform the steps
4 - 7.
4 Open the PDM.
5 Put the spare handset in the Desktop Programmer (DP1)cradle.
6
Run the template with the basic network settings containing (see 4.4 Configure a
Handset with a Template on page 13):
• Network settings
1
(located under Network > Network A, B, C, or D)
• VoIP settings
2
(located under VoIP)
• Unite settings
3
(located under Device > Unite)
7 Remove the handset from the Desktop Programmer (DP1)cradle. The handset might
be restarted depending on parameter changes.
8
Enter the number and the password
4
(if any). Press “Login”.
The spare handset is automatically updated from the IMS3 and might be restarted
depending on the param
eter changes. The last stored settings for the broken handset in the
IMS3 has been transferred to the new handset.
Replace and Move License using PDM and IMS3
The broken handset and the spare handset do not have
the same device t
ype and/or have
the same functionality license.
In order to move the licenses to the spare handset, it must be an unlicensed Talker. To check
that the handset is unlicensed, press *#34# in idle mode and select “License“. Only i62
Talker must be displayed here.
1 Make sure that the broken handset is saved in the Device Manager (indicated by a
in the Saved column. If not, in the Numbers tab, right-click the broken handset
and select “Save“.
2 Switch off the broken handset to make it offline.
3 Open the PDM.
4 Put the unlicensed spare handset (Talker) in t
he Desktop Programm
er (DP1)cradle.
5 Run the template with the basic network settings containing (see 4.4 Configure a
Handset with a Template on page 13):
• Network settings
1
(located under Network > Network A, B, C, or D)
• VoIP settings
2
(located under VoIP)
• Unite settings
3
(located under Device > Unite)
1. All required system settings for the WLAN. For example SSID and Security mode.
2. VoIP protocol, Gatekeeper IP address or SIP Proxy IP address used to access the PBX.
3. IP address and password (if any) to the IMS3
.
4. The password is only required if
the “Password“ parameter is set.