User manual
Table Of Contents
- 1. Introduction
- 2. Pre-Installation
- 3. Programming the VoWiFi Handset
- 4. Installation of VoWiFi Handsets
- 5. Maintenance
- 5.1 Handset
- 5.1.1 Configure Spare Handsets without a Number in Large Systems
- 5.1.2 Upgrade Handset Software
- 5.1.3 Upgrade Software OTA via TFTP
- 5.1.4 Upgrade Software via PDM
- 5.1.5 Upgrade Software Over the Air (OTA) via Centralized Device Management (IMS3)
- 5.1.6 Recapture the Earlier Software
- 5.1.7 Upgrade Handset Functionality using License
- 5.1.8 Perform a Factory reset
- 5.2 Replacement of Handsets
- 5.3 Change Number of a Handset
- 5.4 Update Parameters via IMS3
- 5.5 Perform a Security Upgrade via IMS3
- 5.6 Upgrade the Template
- 5.7 Create a Configuration Backup
- 5.1 Handset
- 6. Handset Configuration
- 6.1 Select Network
- 6.2 IP Address Settings
- 6.3 Network Settings
- 6.4 Security Settings
- 6.5 Handset Settings
- 6.5.1 Automatic key lock
- 6.5.2 Phone lock
- 6.5.3 Audio adjustment
- 6.5.4 Headset Configuration
- 6.5.5 In Charger Behavior
- 6.5.6 Configure Profiles
- 6.5.7 Hide Missed Call Window
- 6.5.8 Battery Warning
- 6.5.9 Shared Phone
- 6.5.10 Prevent Handset Switch off
- 6.5.11 Uploadable Language
- 6.5.12 Select Default Language
- 6.5.13 Short cuts
- 6.5.14 Soft Key Functions During Call
- 6.5.15 Import Contacts
- 6.5.16 Company Phonebook
- 6.5.17 Central Phonebook
- 6.6 Messaging and Alarm
- 6.7 Messaging Settings
- 6.8 Alarm Settings
- 6.9 Telephony
- 6.9.1 Endpoint ID and Endpoint number
- 6.9.2 VoIP Protocol
- 6.9.3 Codec
- 6.9.4 Offer Secure RTP
- 6.9.5 Internal Call Number Length
- 6.9.6 Emergency Number
- 6.9.7 Voice Mail Number
- 6.9.8 Message Centre Number
- 6.9.9 Max number of Call Completions
- 6.9.10 Dial Pause Time
- 6.9.11 Direct off Hook from Charger
- 6.9.12 Replace Call Rejected with User Busy
- 6.9.13 Busy on 1 / Disable call waiting
- 6.9.14 Calling Line Restriction
- 6.10 Regional Settings
- 6.11 Display
- 6.12 Menu Operation
- 6.13 Push-To-Talk (PTT) Group Call
- 6.14 Presence Management
- 6.15 Location
- 7. Use Handset to Verify the VoWiFi System Deployment
- 8. Handset Internal Web Administration Page
- 9. Administration
- 10. Troubleshooting
- 11. Related Documents
- 12. Document History
- Appendix A: Working with Templates
- Index
- Contents
TD 92675EN
20 June 2012 / Ver. E
Configuration Manual
Ascom i62 VoWiFi Handset
42
6. Handset Configuration
Additional Short Cut Settings
1 In the Function drop-down list, select the funct
ion to be used:
•Phone call
•Call List
• Contact list
• Central phonebook (system dependent feature)
• Message inbox
• Send a message
• Change profile (if selecting profile 1-4, the profile must first
be configured, se
e
6.5.6 Configure Profiles on page 38.)
•Open a menu
•Services
• Logout (applicable for the license dependent Shared Phone feature)
• Presence (system dependent feature)
•Call diversions
• RSSI measurement
2In the Value
field, ent
er the applicable value. This is mandatory when using Phone call
function.
3 In the Control Question drop-down list, select “Enable“ if the Pr
oceed? window shall
be displayed after the key is pressed. This is used to avoid that a function is accessed
by mistake.
4In the Read Only drop-down list, select “True“ if the use
r shall not be able to change
the short cut.
6.5.14 Soft Key Functions During Call
It is possible to access a predefined funct
i
on by pressing the right soft key during a call.
1 Select Device > Call.
2In the Right i
n call soft key name field, enter the name of the soft key to be displayed
during a call.
3In the Right in call soft key a
ction drop-down list, select one of the following
functions:
•Conference
•Contacts
• Disabled
•End Call
•Hold
•Loudspeaker
• New call (put active on hold)
• Retrieve
•Switch
• Transfer (to held call)
• Transfer to new call (blind transfer)