User's Manual
Table Of Contents
- 1Introduction
- 2Description of the Ascom i63 VoWiFi Handset
- 3Basic Operation
- 4Calling
- 4.1 Open the Call List
- 4.2 Incoming Call
- 4.3 Outgoing Call
- 4.3.1 Pre-Dial
- 4.3.2 Post-Dial with Headset Button
- 4.3.3 Dial Using a Pre-programmed Number
- 4.3.4 Dial a Number from the Call List
- 4.3.5 Dial Last Called Number with Headset Button
- 4.3.6 Dial the Sender of a Message
- 4.3.7 Dial a Number from Contacts
- 4.3.8 Dial a Name from the Central Phonebook
- 4.3.9 Dial a Number from the Company Phonebook
- 4.4 During a Call
- 4.4.1 Adjust the Volume during a Call
- 4.4.2 Open Contacts during a Call
- 4.4.3 Open Messaging Menu during a Call
- 4.4.4 Turn the Microphone On or Off during a Call
- 4.4.5 Lock and Unlock the Keypad during a Call
- 4.4.6 Audio Transfer
- 4.4.7 Start a New Call during Conversation
- 4.4.8 Switch between Calls
- 4.4.9 End a Call
- 4.4.10 Transfer a Call
- 4.4.11 Transfer to New Call
- 4.4.12 Conference Call
- 4.4.13 Call Back
- 4.4.14 Send Call Waiting
- 4.4.15 Answering Call Waiting
- 4.4.16 DTMF
- 4.4.17 Send Data
- 4.5 Loudspeaking Function
- 4.6 Call Diversion
- 4.7 Push-to-Talk Group Call
- 4.8 Emergency Calls
- 5Messaging
- 5.1 Message List
- 5.2 Receive a Message
- 5.2.1 Read a Stored Message
- 5.2.2 Reply to a Message
- 5.2.3 Delete Messages
- 5.2.4 Forward a Message
- 5.2.5 Call the Sender of the Message
- 5.2.6 Call a Number Included in a Message
- 5.2.7 Save Number
- 5.2.8 Message Templates
- 5.2.9 Write and Send a Message
- 5.2.10 Open a Sent Message
- 5.2.11 Review Inbox Content while Reading a Message
- 5.3 Receive a Message with Request for Answer
- 5.4 Message Queuing and Message Priority
- 5.5 Message Priority and Call Priority
- 5.6 Interactive Messaging
- 5.7 Message Indication Repetition
- 5.8 Colored Messaging
- 5.9 Decline a Call with a Predefined Message
- 5.10 Answering a Text Message with a Predefined Message
- 5.11 Calling while Reading a Text Message
- 5.12 Mobile Data
- 5.13 Voicemail
- 6Alarm Operation
- 7Location
- 8Menu Operation
- 9System Profiles
- 10Advanced Functions
- 11Advanced Messaging
- 12System Handling
- 13Operation Notice
- 14Maintenance
- 15Troubleshooting
- 16Energy Efficiency
- 17Related Documents
- 18Revision History
- Appendix ASafety and Regulatory Instructions
- Appendix BMenu Tree
PRELIMINARY
Alarm Operation
USER MANUAL
Ascom i63 VoWiFi Handset
Reset Alarm
1 Reset the alarm in one of the following ways:
• Move the handset to an upright position (after Man-
down).
• Move the handset (after No-movement).
• Press the Mute button if the ALS sounds.
6.5 Alarm with Additional Information
Information about the approximate location of the handset is automatically sent along with an alarm, see
Associated Access Point (AP) Location, page 45. It is also possible to add the location manually, see Alarm
with Data, page 45.
• IR
• LF
• AP
• Alarm with Data
Associated Access Point (AP) Location
This function is used together with an alarm. The AP communicates to the handset where the handset is
located for the time being. This gives a fair indication of the location.
An approximate location of the handset is added to alarms sent from the handset. The handset sends the
current and previous AP location to indicate where the alarm was activated.
Alarm with Data
The data can be defined and stored manually by the user. To use the function, one Soft/Hot key/Navigation
key in the handset must be defined as a shortcut to the menu Edit alarm data, see 8.2 Shortcuts, page 55.
The stored data is added to all types of alarms at transmission.
6.6 Automatic Call after Alarm
A handset can be set up to call a predefined number after an alarm has been sent, for example to “112”
which is the common emergency call number inside the European Union.
Depending on the settings, the call can be established in the following modes:
• Loudspeaking mode
• Monitor mode
• Normal mode
For more information, refer to the Configuration Manual, Ascom i63 VoWiFi Handset, TD 93300EN.
45 TD 93289EN / / Ver.