Model 610 PARTS MANUAL Version4-04 Ashland Industries Inc. 1115 Rail Drive P.O. Box 717 Ashland, WI. 54806 Ph: 877-634-4622 Toll Free Ph: 715-682-4622 Fx: 715-682-9717 www.ashlandind.
Model 610 Scraper HOW TO ORDER PARTS: IMPORTANT Parts must be ordered through your local authorized ASHLAND dealer. Be sure to state MODEL and SERIAL NUMBER of your machine, PART NUMBER, DESCRIPTION and QUANTITY needed. Unless this is done, we cannot provide prompt service or assure shipment of the correct parts. Ashland Industries weldable replacement parts are availabe to rebuild, modify or update your scraper to current factory specifications.
OPERATOR AND MAINTENANCE INSTRUCTIONS The scraper is a durable piece of equipment and with proper care will yield many years of trouble free operation. The scraper requires a power source with one 4-way (double acting) hydraulic control valve. After scraper has been assembled, it should be greased at all points where grease fittings are provided. Connect hydraulic hoses to tractor and operate the scraper to maximum raise and drop several times to force any air from the hydraulic lines and cylinders.
SAFETY SIGNAL WORDS Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each has been selected using the following guidelines: DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations typically for machine components which, for functional purposes, cannot be guarded.
Model 610 Scraper Assembly Instructions 1. A suitable hoist or lift should be available for assembly. 2. Install rear spindles to frame in the lowest possible setting to obtain the maximum spreading depth between the cutting edge and ground. If less depth of spread is desired, select a lower setting or reverse the spindle - bottom to top. 3. Pack wheel bearing with grease and install hubs to rear spindles and front axle assembly.
base (rear) port of the cylinder. D. Connect a ½” x 38” hose from the pipe line on the frame cross-member to the center port of the cylinder. E. Connect a ½” x 38” hose from the center pipe line on the frame cross-member to the extreme forward port of the cylinder. F. Install the cylinder with two hose ports on the right side of the scraper with the rod end to the actuating frame, and the grease hole in the rod end bushing facing up. Use the same size pins as the cylinder on the left side. G.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PART NO. DESCRIPTION Frame, FOUR WHEEL, Model, D Bolt, 5/8" x 4" NC, w/ nut & LW Grease fitting, 1/8" NPT straight, long Socket half, rear w/ grease hole Socket half Bolt, 1-1/4 x 7" NF w/ lock nut Swivel hitch Frame, TWO WHEEL, Model S Hydraulic hose, 1/2" x 18" Hydraulic hose, 1/2" x 24" Hydraulic hose, 1/2" x 38" Pin, 1-1/8" x 3-1/4" Cotter both ends Cotter pin, 3/16" x 1-1/2" Pin, 1-1/8" x 3-1/8" w/ sq.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PART NO. A5006 A5005 A40006 AFB-00005 A2229A A2230A A2231 A2232 A2236 A2233 A2234 A2239 AFN-00005 A2235 A3319A A4553 A6014 A4553A A6012 A021468 A051368 A051368-2 DESCRIPTION Spindle - bolt on Pole Assembly Bolt, 1/2" x 4-1/2" Gd.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. A6105 A4524 A6101 A6102 A6106 A6107A A30020 A6007A A6108 A6109 DESCRIPTION Actuating frame Pin, 1-1/8" x 6" w/ tab head Capscrew, 1/2" x 1" NC w/ LW Pin, 1-3/4" x 6" w/ tab head Pin, 1-1/4" x 2-11/16" w/ tab head Capscrew, 5/8" x 1-1/2" w/ nut & LW Actuating link Stop block Bolt, 3/8" x 4-1/2" NC w/ nut & LW Shoulder pin, 1-1/4" x 1" w/ ctsk grease hole Cotter pin, 1/4" x 2" Pin, 1-1/4" x 4-1/8" w/ sq. head & hole for gr. zerk Actuating arm, R.H.
9 KEY NO. 1 2 3 * 4 5 6 7 8 PART NO.
* (Serial number break) KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. A4520 A4512 A4513 A4514 A4515 A4519 A2239 *A4521A *A125047 A2235 AFN-00005 A2234 A2233 DESCRIPTION Spindle, rear with flange Grease seal ( National 415082 ) Bearing cone, inner ( Timken 3784 ) Bearing cup, inner ( Timken 3720 ) Hub, with bearing cups Wheel bolt Washer, special 7/8" flat Cotter pin Wheel, 20" D.C. (up to sn 20667) Dec 2002 Wheel, 22.5” x 8.
CYLINDER KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. A516H118 PART NO.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. A400H17 A400H04 A600H50 A22H27 A400H08 A600H30 A600H06 A400H10 AA400H11 A400H12 A400H12A A400H13 A400H14 A22H18 A600H53C DESCRIPTION Piston nut, 1-1/4" NF Cast iron ring, 5" OD Piston, 5" OD O-ring, 1-1/4" ID x 1/8" Shaft, 2" dia.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. A300H03 A300H04 A300H05 A300H06 A300H07 A45H05 A600H32 A600H33 A300H11 A300H12 A22H15 A22H15A A300H13 A22H17 A22H18 A300H14C DESCRIPTION Piston nut, 1" NF Cast iron ring, 4" OD Backup washer O-ring, 4" OD, x 3/16" Piston, 4" OD O-ring, 1" ID Shaft, 1-1/2" dia.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 PART NO. A600H22 A600H20 A600H18 A600H16 A600H14 A600H13 A600H15 A600H17 A600H19 A600H21 A600H23 A600H24 DESCRIPTION Relief seat O-ring Ball Valve body gasket Adjusting screw O-ring Jam nut Acorn cap Adjusting screw Valve body Spring Relief seat Valve housing Complete valve assembly KEY NO. 1 2 3 PART NO.
KEY NO. *1 *2 *3 *4 *5 *6 *7 *8 9 *10 *11 PART NO. DESCRIPTION A600H01 Valve stem plug A600H02 O-ring, seal A600H03 Spring A600H04 Ball valve A600H05 Valve seat sleeve A600H07 O-ring seal A600H08 Backup washer A600H06 O-ring seal A600H10 Valve housing A600H09A Plunger kit A600H11 Plug A600H12 Complete valve assembly * Parts sold in kit only, Kit No.
PIPE AND FITTINGS KEY NO. DESCRIPTION LENGTH 1 1/2" STD Black Pipe 91 2 1/2" STD Black Pipe 82-5/8 3 1/2" STD Black Pipe 33-1/2 4 1/2" STD Black Pipe 28-3/4 4b 1/2" STD Black Pipe 42-1/4 5 1/2" STD Black Pipe 39 6 1/2" STD Black Pipe 30-1/2 7 1/2" STD Black Pipe 90 8 1/2" STD Black Pipe 41-1/2 9 1/2" STD Black Pipe 46-1/2 10 1/2" STD Black Pipe 3 11 1/2" NPT Close nipple 12 1/2" NPT x 90° elbow 13 1/2" NPT x 45° elbow 14 1/2" NPT x 90° st.
Limited Warranty Statement Ashland Industries Inc. warrants each new product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed six consecutive months from the date of delivery of the new Ashland Industries product to the purchaser, or the date the product is first put into service via a rental agreement or other means, whichever occurs first.
