Model 80 PARTS MANUAL Version 4-04 Ashland Industries Inc. 1115 Rail Drive P.O. Box 717 Ashland, WI. 54806 Ph: 877-634-4622 Toll Free Ph: 715-682-4622 Fx: 715-682-9717 www.ashlandind.
Model 80 Scraper HOW TO ORDER PARTS: IMPORTANT Parts must be ordered through your local authorized ASHLAND dealer. Be sure to state MODEL and SERIAL NUMBER of your machine, PART NUMBER, DESCRIPTION and QUANTITY needed. Unless this is done, we cannot provide prompt service or assure shipment of the correct parts. Ashland Industries weldable replacement parts are availabe to rebuild, modify or update your scraper to current factory specifications.
OPERATOR AND MAINTENANCE INSTRUCTIONS This scraper is a durable piece of equipment and with proper care will yield many years of trouble free operation. The scraper requires a power source with one 4-way (double acting) hydraulic control valve. After scraper has been assembled, it should be greased at all points where grease fittings are provided. Connect hydraulic hoses to tractor and operate the scraper to maximum raise and drop several times to force any air from the hydraulic lines and cylinders.
SAFETY SIGNAL WORDS Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The appropriate signal word for each has been selected using the following guidelines: DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations typically for machine components which, for functional purposes, cannot be guarded.
ASSEMBLY INSTRUCTIONS FOR MODEL 80 SCRAPER (Refer to illustration on previous page) 1. A suitable hoist or lift should be available for assembly. 2. Install rear spindles to frame in lowest possible setting to obtain the maximum spreading depth between cutting edge and ground. If less depth of spread is desired, select a lower setting or reverse the spindle bottom-to-top. 3. Pack wheel bearings with grease and install hubs to rear spindles and to front axle assembly on model 80D scrapers. 4.
12.Connect a ½” x 38” hose from the front port of each cylinder to the remaining pipe line on the rear cross frame. 13.Install front apron gate and secure with 1 ¼” to 1 5/8” shoulder pin with zerk in head end. (Point F) 14.Install the two apron actuating links (open spring end toward front of scraper). Secure at Point E with 1 ¼” to 1-5/8” shoulder pin having zerk in threaded end. Secure at Point G with 1 ½” flat washer and ¼” x 2” cotter pin. 15.Raise the rear of frame and install wheels to hubs.
KEY NO. PART NO.
Linkage Cylinder DWG # 123119 123120 123122 123121 123123 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO.
( 4-Wheel Models Only) KEY NO. 1 2 3 4 5 6 7 8 9 10 11 PART NO. A8014 A6013 A6014 A40006 A8027 A8015 A021468 A051368 A051368-2 DESCRIPTION Pole and Axle Swivel hitch clevis Pin, 1-1/4" x 6-3/4" w/ 5/16" x 2-1/2" bolts Ball swivel Bolt, 3/4" x 2-1/2" w/ nut & lockwasher Washer, special 1-1/4" flat Nut, 1-1/4" NF castellated Swivel Hitch Rebuild Kit, includes items 3, 9, 10, 11.
KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO.
KEY NO. PART NO.
s/n 12592 & up KEY NO. PART NO.
KEY NO. 1 2 3 4 5 6 7 8 9 10 PART NO. A400H17 A400H04 A400H05 A400H06 A80H01 A60H52 A80H08A A8007A 11 *12 13 *14 15 A80H02 A80H03 A80H04 A80H05 A80H06 A80H07 *16 A80H05A A45003 DESCRIPTION Nut, 1-1/4" NF, lock type Cast ring, 5" OD Backup washer, 5" OD x 1/4" O-ring, 5" OD x 1/4" Piston, 5" OD O-ring, 1-1/4" ID x 1/16" Shaft, 2" dia.
Limited Warranty Statement Ashland Industries Inc. warrants each new product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed six consecutive months from the date of delivery of the new Ashland Industries product to the original purchaser, or the date the product is first put into service via a rental agreement or other means, whichever occurs first. Genuine Ashland Industries Inc.
