Installation Guide

ManualsBrandsAshley Harbour ManualsVanity LightsBrandt 3-Light 23.5-in Polished chrome Bell Vanity Light

Model#

LWS0038C

Item# 0035151

Package Contents

Tools Required

Bulb Recommended:

Estimated Assembly Time

Preparation

(not included): Flathead screwdriver, Phillips screwdriver, Electrical

tape, Safety goggles.

(3) 100W Type-A medium base bulbs, Alternate (3) bulbs.

: 20 - 30 minutes

Identify and inspect all parts before beginning installation

Check package contents list and diagrams below to be sure all parts are included.

If any parts are missing or damaged, do not attempt to assemble, install or operate

the fixture.

LED

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in

doubt.

These instructions are provided for your safety. It is very important you read them completely before installing

fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs.

- Make sure bulbs are given sufficient time to cool before removal.

- Do not subject glass parts to any shock while in operation or shattering may result.

Warnings And Cautions

Español p. 9

Français p. 5

Toll Free Phone:

1-800-645-3184,

8a.m.-5p.m.,EST,

Monday - Friday.

G1987SH

Stock Part#

N/A

Shade

Fixture Body

Socket Collar

(Pre-assembled to fixture body)

3pcs

1pc

N/A

PART

DESCRIPTION

QUANTITY

3pcs

2pcs

3pcs

Wire Connector

Outlet Box Screw

Mounting Screw

(Pre-assembled to fixture body)

Crossbar

(Pre-assembled to fixture body)

1pc

Green Ground Screw

()Pre-assembled to Crossbar

2100 Stemmons

Freeway

3rd Floor, Space

3200

Dallas, TX 75207

September 2016

Summary of content (12 pages)

PAGE 1
Model# LWS0038C 2100 Stemmons Freeway 3rd Floor, Space 3200 Dallas, TX 75207 Toll Free Phone: 1-800-645-3184, 8 a.m. - 5 p.m., EST, Monday - Friday. Item# 0035151 Français p. 5 Español p. 9 Tools Required (not included): Flathead screwdriver, Phillips screwdriver, Electrical tape, Safety goggles. Bulb Recommended: (3) 100W Type-A medium base bulbs, Alternate (3) LED bulbs.
PAGE 2
8” 23.5” 6”Dia. 4.75” 9.
PAGE 3
STEP 1: Note : Prior to installation, close or cover the sink drain and/or any vents near the installation site to prevent loss of mounting hardware if dropped. a. Remove the Crossbar from the Backplate on the Fixture Body as shown in STEP 3. b. Secure the Crossbar to the outlet box (not included) with Outlet Box Screws. Note : Fixture Body can be installed with the sockets facing either up or down. The Crossbar should be adjusted accordingly to match the holes on the backplate of the Fixture Body.
PAGE 4
STEP 5: a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage. Your installation is completed now. Restore electricity. Retain this sheet for future reference. CARE AND MAINTENANCE • Wipe clean using soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixture as they may damage the finish. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION 1 . Replace light bulb. 2. Make sure power supply is on. 3. Check wiring. 4.
PAGE 5
Modèle # LWS0038C 2100 Stemmons Freeway 3rd Floor, Space 3200 Dallas, TX 75207 Service à la clientèle Numéro de téléphone sans frais: 1 800 645-3184, entre 8 h et 17 h (HNE), du lundi au vendredi. Article # 0035151 Outils nécessaires (non inclus) : tournevis à tête plate, tournevis cruciforme, ruban isolant, lunettes de sécurité et échelle. Ampoules recommandées : 3 ampoules de type A à culot moyen de 100 W, 3 ampoules LED de rechange. Temps d'assemblage approximatif : de 20 à 30 minutes.
PAGE 6
20.3cm 59.7cm 15.2cm Dia. 12cm 24.
PAGE 7
ÉTAPE 1 : Remarque : Avant de commencer l'installation, bouchez ou couvrez le drain de l'évier ou tout évent se trouvant à proximité de l'endroit où vous désirez installer l'article pour éviter de perdre la quincaillerie de fixation si vous l'échappez. Support de fixation a. Retirez le support de fixation de la plaque murale du corps du luminaire, tel qu'il est illustré à l'ÉTAPE 3. b. Fixez le support de fixation à la boîte de sortie (non incluse) à l'aide des vis pour boîte de sortie.
PAGE 8
ÉTAPE 4 : a. Retirez la bague de douille de la douille du luminaire. b. Ensuite, placez l'abat-jour sur la douille du luminaire, tel qu'il est illustré. c. Fixez le tout en vissant la bague de douille à la douille. d. Serrez fermement à la main. Bague de douille Abat-jour Corps du luminaire ÉTAPE 5 : a. Posez des ampoules dont la puissance est conforme aux indications ou aux étiquettes du luminaire.
PAGE 9
Modelo # LWS0038C 2100 Stemmons Freeway 3rd Floor, Space 3200 Dallas, TX 75207 Servicio al cliente Número de teléfono gratuito: 1 800 645-3184, de lunes a viernes de 8 a.m. a 5 p.m., hora estándar del Este. Artículo # 0035151 Herramientas necesarias (no se incluyen): Destornillador de cabeza plana, destornillador Phillips, pinzas cortacables, cinta aislante, gafas de seguridad y escalera. Bombilla recomendada: 3 bombillas de base media tipo A de 100 W o, alternativamente, 3 bombillas LED .
PAGE 10
20.3cm 59.7cm 15.2cm Dia. 12cm 24.1cm NOTA: TODAS LAS DIMENSIONES ESTÁN APROXIMADAS A LO MÁS CERCANO A 1,27 cm.
PAGE 11
PASO 1: Nota : Antes de instalar, cierre o cubra el desagüe y cualquier respiradero cerca del lugar de instalación, para evitar la pérdida de aditamentos de montaje si se caen. Barra transversal a. Retire la placa perforada de la placa posterior del cuerpo de la lámpara, como se muestra en el PASO 3. b. Fije la placa perforada a la caja de salida (no incluida) con los tornillos para la caja de salida. Nota : El cuerpo de la lámpara se puede instalar con los portalámparas hacia arriba o hacia abajo.
PAGE 12
PASO 4: a. Retire el anillo del portalámparas del ensamble de la lámpara. b. Luego coloque la pantalla sobre el portalámparas en el ensamblaje de la lámpara, como se muestra. c. Enrosque el anillo del portalámparas en el portalámparas para asegurar la pantalla. d. Apriete a mano hasta que esté ajustado. Anillo del portalámparas Pantalla Cuerpo de la lámpara PASO 5: a. Instale las bombillas correctas consultando las marcas o las etiquetas en la lámpara para conocer el vataje máximo.