Use and Care Guide

ManualsBrandsAshley Hearth Products ManualsHeating, Ventilation, and Air Conditioning31,000 BTU Vent Free Natural Gas Stove Black Enameled Porcelain Cast Iron

• Do not store or use gasoline or other ammable vapors and liquids in vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow gas supplier's instructions

• If you cannot reach your gas supplier, call re department.

• Installation and service must be performed by a qualied installer, service agency or gas supplier.

852404C-3602F

Installation and Operating Manual

AGC500VF

This is an unvented gas-red heater. It uses air (oxygen) from room in which it is installed. Provisions for

adequate combustion and ventilation air must be provided. Refer to section,” Producing Adequate Air

For Combustion And Ventilation". This appliance may be installed in an aftermarket, permanently located,

manufactured (mobile) home, where not prohibited by local codes. This appliance is only for use with type

of gas indicated on rating plate. This appliance is not convertible for use with other gases.

WARNING

If the information in this manual is not followed exactly, a re or explosion may result causing property

damage, personal injury or loss of life.

Certied for installations in the USA

Approved for installation in mobile homes

INSTALLER: Leave this manual with appliance.

CONSUMER: Retain this manual for future reference.

This appliance is intended for supplemental heating.

CALIFORNIA PROPOSITION 65 WARNING:

This product can expose you to chemicals including carbon monoxide, which

is known to the State of California to cause cancer, birth defects and/or other

reproductive harm. For more information, go to www.P65warnings.ca.gov

Ce produit peut vous exposer à des produits chimiques, y compris le

monoxyde de carbone, qui est connu dans l'État de Californie pour causer

le cancer, des malformations congénitales et / ou d'autres problèmes de

reproduction. Pour plus d'informations, visitez www.P65warnings.ca.gov

Summary of content (24 pages)

PAGE 1
Installation and Operating Manual AGC500VF WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. • Do not store or use gasoline or other flammable vapors and liquids in vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS: • • • • • Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building.
PAGE 2
Important Safety Information Congratulations! PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of an Ashley stove. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. IMPORTANT: READ THIS OWNER’S MANUAL CAREFULLY AND COMPLETELY BEFORE TRYING TO ASSEMBLE, OPERATE, OR SERVICE APPLIANCE.
PAGE 3
Important Safety Information 13. Avoid any drafts that alter burner flame patterns. Do not allow fans to blow directly into fireplace. Do not place a blower inside burn area of firebox. Ceiling fans may create drafts that alter burner flame patterns. Sooting and improper burning will occur. 14. Caution: Candles, incense, oil lamps, etc. produce combustion by-products including soot. Vent-free appliances will not filter or clean soot produced by these types of products.
PAGE 4
Product Features Gas Pressures Natural Propane (LP) Regulator Pressure 3.5” w.c. 10.0” w.c. Pilot Regulator 3.5” w.c. n/a Max. Gas Inlet Pressure 10.5” w.c. 13.0” w.c. Min. Gas Inlet Pressure 5.0" w.c. 11.0" w.c. Fuel Control Max. Input BTU/h Min. Input BTU/h Nat. Millivolt 32,000 23,000 LP Millivolt 32,000 23,000 On/Off Switch NOTE: An external regulator is required to reduce supply pressure to a maximum of 10.5" w.c. on Natural Gas systems operating at higher pressure.
PAGE 5
Getting Started Caution: Gloves are recommended when handling ceramic fiber logs to prevent skin irritation from loose fibers. Logs are fragile — handle with care. MAKE SURE YOU HAVE RECEIVED ALL PARTS Check your packing list to verify that all listed parts have been received. You should have the following: • Cast Iron Stove with Burner Assembly • Installation/Operating Instructions • Ceramic Fiber Logs Carefully inspect the contents for shipping damage.
PAGE 6
Clearances And Height Requirements WARNING The dimensions shown are minimum clearances to maintain in installing this heater. Left and right clearances are determined when facing the front of the heater. Follow these instructions carefully to ensure safe installation. Failure to follow instructions exactly can create a fire hazard. The appliance cannot be installed on a carpet, tile or other combustible material.
PAGE 7
Clearances/Height Requirements C B A Alcove Installation NOTE: Maintain minimum side and back clearances when placing stove in alcove.
PAGE 8
Installation Caution! The appliance is very heavy. The assistance from a second person is strongly suggested. Please use proper lifting technique when positioning the appliance for assembly and installation. STEP 1 Remove the two (2) straps, and open the wrapping. Slide the bag to the bottom of the unit. Straps Wrapping ON OFF LO GS Pallet Leg is removed for Leg is only removed for pictorial purposes pictorial purposes only STEP 2 Lift up on the ash lip.
PAGE 9
STEP 3 Lift up on the front of the stove. Pivot the bottom out towards you. Pull down to remove front. Note: When handling the stove be careful not to damage the porcelain finish of the unit. BACK BACK Screen BACK Screen Screen UP UP UP STEP 4 Remove the two screws located at the bottom of the screen as shown. Lift up and back on the screen to remove. Side of unit is removed for pictorial purposes only STEP 5 Log Box S G O L Remove log box from inside of unit. Lift unit off pallet.
PAGE 10
Connect Gas Line WARNING Use new black iron or steel pipe. Internally tinned copper or copper tubing can be used per National Fuel Code, section 2.6.3, providing gas meets hydrogen sulfide limits, and where permitted by local codes. Gas piping system must be sized to provide minimum inlet pressure (Listed on Data Plate) at the maximum flow rate (BTU/hr). Undue pressure loss will occur if the pipe is too small. A manual shutoff valve must be installed upstream of the appliance.
PAGE 11
Electrical Wiring (Millivolt) The millivolt valve is a self-powered combination gas control THAT DOES NOT REQUIRE 110V AC TO OPERATE . Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. CONNECT OPTIONAL WALL SWITCH 1. Use 18 awg, two-wire cable, 15 feet maximum length. 2. At one end of the cable, connect both wires to the wall switch.
PAGE 12
Log Placement Top Left Log #4 Right Bottom Log #3 Top Left Log #4 Right Right Right Top Log #5 Bottom Bottom WARNING Log #3 The positioning of the logs is critical to the safe and clean operation of this heater. Sooting and otherLog #3 problems may result if the logs are not properly and firmly positioned in the appliance. Never add additional Left logs or embellishments such as pine cones, vermiculite or rock wool to the heater. Only Top use the logs supplied Log #4 Right Bottom with the unit.
PAGE 13
Flame Appearance Flames from the pilot, front and rear burner should be visually checked as soon as the heater is installed. In addition, periodically check the flames visually during operation. PILOT FLAME The pilot flame must always be present when the heater is in operation. It should just touch the top of the thermocouple tip for natural. Refer to the figure below for correct pilot flame. If the pilot flame does not touch the thermocouple, then the burners cannot function reliably.
PAGE 14
OPERATING INSTRUCTIONS Operating Instructions Avoid any drafts that alter burner flame patterns. Do not allow fans to blow directly into the stove. Do not place a blower inside the burn area of the stove. Ceiling fans may create drafts that alter flame patterns. Sooting and improper burning will result. During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents.
PAGE 15
Operating Instructions MILLIVOLT CONTROL LIGHTING INSTRUCTIONS 1. STOP! Read the safety information label. 2. Make sure the manual shutoff valve is fully open. 3. This gas log set is equipped with an ignition device (piezo) which automatically lights the pilot. If piezo ignitor does not light the pilot, refer to instructions for “Match Lighting Instructions”. 4. Turn gas control knob clockwise to the OFF position, and turn ON/OFF switch to OFF position. 5. Wait (5) minutes to clear out any gas.
PAGE 16
Cleaning And Servicing WARNING Turn off heater and allow to cool before cleaning. Disconnect electrical power before cleaning or servicing. CLEANING AND SERVICING Annual inspection and cleaning by your dealer or qualified service technician is recommended to prevent malfunction and/or sooting. Remove logs, handling carefully by holding gently at each end. Gloves are recommended to prevent skin irritation from ceramic fibers. If skin becomes irritated, wash gently with soap and water.
PAGE 17
Troubleshooting WARNING Turn appliance OFF and allow to cool before servicing. Only a qualified service person should service and repair the heater. NOTE: All troubleshooting items are listed in order of operation. OBSERVED PROBLEM POSSIBLE CAUSE When ignitor button is pressed, there is no spark at ODS/pilot. 1. Ignitor electrode positioned wrong. 2. Ignitor electrode is broken. 3. Ignitor electrode not connected to ignitor cable. 4. Ignitor cable pinched or wet. 5. Broken ignitor cable. 6.
PAGE 18
Troubleshooting WARNING If the gas quality is bad, your pilot may not stay lit, the burners may produce soot and the heater may backfire when lit. If the gas quality or pressure is low, contact your local gas supplier immediately. OBSERVED PROBLEM POSSIBLE CAUSE 1. 2. 3. 4. REMEDY ODS/pilot lights, but flame goes out when control knob is released. Control knob not fully pressed in. Control knob not pressed in long enough. Manual shutoff valve not fully open.
PAGE 19
Requirements for the Commonwealth of Massachusetts This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts. NOTE REGARDING VENTED PRODUCTS Flex line installation must not exceed 36 inches and must have a T shutoff valve. Any residence with a direct vent product must have a CO detector installed in the residence.
PAGE 20
Manufacturer Requirements GAS EQUIPMENT VENTING SYSTEM PROVIDED When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include: • Detailed instructions for the installation of the venting system design or the venting system components; and • A complete parts list for the venting system d
PAGE 21
Replacement Parts 1 2 6 3 5 7 4 12 8 13 9 14 15 10 11 17 16 27 29 18 26 28 19 25 24 23 20 22 21 21
PAGE 22
Replacement Parts Ref. Part No. Description Qty. 1 40861 VF Grate 1 2 40860 VF Top 1 3 40857 Left Side 1 4 40856 Right Side 1 5 27225 Log Retainer, Side 2 6 27222 Log Support, Rear 1 7 C42373 Rocker Switch 1 8 892537.13 Base Assembly 1 9 892537.7 Control Panel 1 10 892537.
PAGE 23
Notes 23
PAGE 24
How To Order Repair Parts This manual will help you obtain efficient, dependable service from your Appliance dealer, and enable you to order repair parts correctly. Keep this manual in a safe place for future reference. When writing, always give the full model number which is on the nameplate attached to the heater. When ordering repair parts, always give the following information as shown in this list: 1. The part number_______________________________________________ 2.