Specifications Sheet

11" [279]
15-
1
2
"
[394]
FRONT VIEW
SIDE VIEW
5-
23
32
" [145]
2-
9
16
" [65] 3-
5
32
" [80]
ROUGH WALL
OPENING
MINIMUM
DEPTH
3-
1
4
"
[83]
NOTE:
ALL DIMS
INCH [MM]
7"
[178]
7-
7
8
" [200]
1-
5
8
"
[42]
3-
9
16
"
[90]
7-
1
2
"
[191]
3-
9
16
"
[90]
10-
1
2
" [267]
15-
1
8
"
[384]
1
2
" [13]
5"
[127]
1-
3
16
" [30]
7
32
" DIA [Ø6]
MOUNTING
HOLES
7
8
" DIA [Ø22]
4 KNOCKOUTS
POWER ENTRY
1 EACH SIDE
2 BOTTOM
MOUNTING HEIGHT
64-
11
16
" to 71-
11
16
" [1643-1821]
ADAAG 56-
11
16
" [1440] MAX AFF
CalDAG 48-
11
16
" [1237] MAX AFF
5" [127]
5-
1
4
"
[134]
5" [127] 3" [76]
2-
3
4
" [70]
5-
3
8
"
[137]
P
P
P
PP
1-
1
4
" [32]
PP
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
AMERICAN SPECIALTIES, INC.
441 Saw Mill River Road, NY 10701
[phone] • [phone]
www.americanspecialties.com
ROVAL™ COLLECTION SEMI-RECESSED AUTOMATIC HAND DRYER (PG 1 OF 2)
MODEL №: 20199
ISSUED: 06/10
REVISED: 28 May 2013
SPECIFICATION
Roval™ Collection Semi-Recessed Hand Dryer operates automatically from IR sensor that activates dryer when hands are placed in sen-
sor zone. Cabinet full panel shall be drawn seamless and shall have bowed front face and gently radiused edges to provide added strength
and complimentary appearance for modern washroom aesthetics. Cover shall be fabricated in one piece of 18 gauge (.048", {1.2}) thick
type 304 stainless steel alloy 18-8. Hand drying recess shall be same grade and gauge. All exposed surfaces shall have a satin finish and
shall be protected during shipment by PVC film easily removable after installation. Cabinet shall be 20 gauge corrosion protected steel
with a 1/2" (13) wide perimeter trim to lay flush against wall and shall have concealed pin-hex security screws to close cover. Motor and
heating element shall have internal resetting automatic thermal protection. Fixed directional air vanes shall be heavy duty, rust proof and
tamper resistant. Air intake slots shall not allow access to internal parts. Circuitry shall have self-adjusting time-out and fail-safe off pro-
tection controlled by a microprocessor that shall detect and reject false signals and shall automatically self calibrate to provide uniform
sensitivity over its entire life span. Entire unit shall be internally electrically grounded. Dryer unit shall have approval and be listed under
the re-examination services of Underwriters Laboratories, Inc. Unit shall be warranted against defects in materials or workmanship for
five (5) years.
Roval™ Collection Semi-Recessed Sensor Hand Dryer shall be Model № 20199 of American Specialties, Inc., 441 Saw Mill River
Road, Yonkers, NY 10701-4913
INSTALLATION
Mount unit cabinet in wall recess with four (4) № 10 (M5) screws (not supplied) into suitably prepared mountings (by others) or other
suitable mounting hardware (by others) to suit wall conditions. For masonry walls use expansion bolts or anchors for 1/4" (M6) screws.
See unit diagram for electrical service cable rough-in location. Electric service of 100-240VAC 20A 50/60 Hz (provided by others) is
brought to RWO at location for dryer indicated on diagram above and is hooked up (by others) in accordance with schematic and
Owner’s Manual provided with unit. Electrical service is supplied and connected (by others) prior to installing cover. Cover is secured to
cabinet with two (2) concealed pin-hex socket button head security screws (supplied). For compliance with ICC/ANSI A-117.1-2003 and
2010 ADA Accessibility Standards install unit with top of dryer hand chamber 48" (1219) maximum above finished floor (MAX AFF) if
clear floor reach access is provided or 46" (1168) MAX AFF if side reach access over an obstruction (e.g. vanity) with reach depth
greater than 10" (254) and less than 25" (635) is only provided or 44" (1118) MAX AFF if forward reach over an obstruction (e.g. com-
mode) with reach depth greater than 20" (508) and less than 25" (635) is only provided. For general utility install unit so that top of dryer
hand chamber is 44" to 50" (1118 to 1270) AFF. Note that top of RWO is 3/8" (10) below top of unit. For installation of two or more
dryers, dryers should be no closer than 24" (610) on center.