User's Manual

ManualsBrandsAsian Express Holdings ManualsDronesAir Micro Drone

Trim size 4.5 x 6.875 in.

Spread size 9 x 6.875 in.

Made in China

Conforms to safety requirements of ASTM, CPSIA and FCC.

Tel: + (1) 949-566-9573 • www.propelrc.com

CHOKING HAZARD

Small parts.

Not suitable for children under 3 years.

WARNING!

WARNING: Never leave product charging unattended for extended periods of

time. Always disconnect the Air™ from charger immediately after it is

fully charged. Please refer to enclosed safety instructions.

INSTRUCTION BOOKLET

Colors and styles may slightly vary.

PACKAGE CONTAINS:

Instruction Manual

Spare Parts USB charging cord

2.4G Wireless ControllerAIR™

AIR™ MICRO DRONE

INDOOR / OUTDOOR WIRELESS QUADROCOPTER

OFF ON

INDUSTRY CANADA NOTICE: CANADA ONLY.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation

est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit

accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and

its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for

successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et

d'un gain maximal (ou inf érieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope

rayonn ée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Summary of content (6 pages)

PAGE 1
Trim size 4.5 x 6.875 in. Spread size 9 x 6.875 in. AIR™ MICRO DRONE INDOOR / OUTDOOR WIRELESS QUADROCOPTER INDUSTRY CANADA NOTICE: CANADA ONLY. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 2
TABLE OF CONTENTS Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Charging Your Air™ Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Air™ Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
AIR™ DIAGRAM WARNING Rear Rotor Blades DO NOT FLY YOUR AIR™ IN FOUL WEATHER! Charging Socket SYNCING YOUR AIR™ Landing Gear Charging Socket Front Rotor Blades On/Off Switch AIR™ REMOTE DIAGRAM Speed Button Power Indicator Light Backward Trim 360˚ Stunt Roll Button Throttle Control Direction Control Important! When syncing your AIR™ quadrocopter with the controller always make sure that the quadrocopter is on a flat level surface and that your digital trim settings are in the center position.
PAGE 4
RECOGNIZING THE FRONT & BACK OF THE AIR™ Even though the Air™ has four rotors, there is still a “front” or forward facing direction and "back" or backwards facing direction. The front and forward facing direction of the Air™ is the side displays WHITE LED lights (see diagram E ). The rear and backwards facing of the Quadrocopter is the side displays RED LED lights (see diagram E).
PAGE 5
SWITCHING TO HIGH SPEED MODE To change the Air™’s flight speed from the default (low speed) to high speed flight mode: 1. Turn on the remote. 2. Depress the speed button on the top left side you will hear two beeps indicating your drone change to high speed mode (see digram I). 3. To switch back to low speed press the speed button again. 4. Speed mode returns to low speed once the remote is turned off. I PERFORMING A 360º STUNT ROLL Once the Air™ is airborne, 1. Press the 360˚ stunt roll button. 2.
PAGE 6
AIR™ WARNING: FCC Part 15 B Notice The Air™ is designed for INDOOR or OUTDOOR flight. Air™ ‘s blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the Air™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your Air™ so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the Air™.