User Manual

ManualsBrandsAsian Express Holdings ManualsDronesToy Helicopter

USER MANUAL

THIS PACKAGE CONTAINS:

Colors and styles may slightly vary.

WARNING: ATOM I

is an indoor Bluetooth

controlled helicopter. Your ATOM I

helicopter is not suited to handle wind or other outdoor environmental conditions.

Attempting to fly this helicopter outdoors may lead to severe damage.

Made in China

Conforms to safety requirements of ASTM, CPSIA and FCC.

BATTERY WARNINGS

RECHARGEABLE BATTERY:

This helicopter uses an internal Li-Poly rechargeable battery and is not replaceable. If battery no longer stays

charged, dispose of it properly according to local disposal requirements.

CARE AND MAINTENANCE

• Always remove the batteries from the wireless infrared remote control when it is not being used for an extended

period of time.

• To clean, gently wipe the remote control and helicopter with a clean damp cloth.

• Keep the toy away from direct heat or sunlight.

• Do not submerge the toy into water. This can damage the unit beyond repair.

• Parental guidance recommended when installing or replacing the batteries.

FCC Part 15 B Notice

CAUTION: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

•

Consult the dealer or experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

CHOKING HAZARD

Small parts.

Not suitable for children under 3 years.

Spare Parts

USB Charging Cable

PROPEL RC™ and ATOM I™ are trademarks of Rooftop Brands.

Tel: + (1) 949-566-9573 • www.rooftopbrands.com

3-CHANNEL HELICOPTER

WITH GYRO STABILIZATION

Helicopter

Instruction Manual

Summary of content (7 pages)

PAGE 1
BATTERY WARNINGS RECHARGEABLE BATTERY: This helicopter uses an internal Li-Poly rechargeable battery and is not replaceable. If battery no longer stays charged, dispose of it properly according to local disposal requirements. CARE AND MAINTENANCE • Always remove the batteries from the wireless infrared remote control when it is not being used for an extended period of time. • To clean, gently wipe the remote control and helicopter with a clean damp cloth. • Keep the toy away from direct heat or sunlight.
PAGE 2
TABLE OF CONTENTS CHARGING THE HELICOPTER Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 COMPATIBLE Bluetooth® DEVICES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Charging The Helicopter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
MANUAL CONTROL DIAGRAM HELICOPTER DIAGRAM Below is a basic list of features and parts on the helicopter. EMERGENCY STOP BACK Stabilizer bar DIRECTION THROTTLE Main Rotor Blades OPTION EMERGENCY STOP Tail Rotor Blade Power Indicator Light Power Switch Landing Gear TRIM THROTTLE PREPARING FOR FLIGHT • Verify that the “ATOM I” app has been successfully installed on your device as instructed in "PROPEL ATOM I APP INSTALLATION" on page 2. Check to see that your helicopter has been fully charged.
PAGE 4
USING MANUAL CONTROLS Below is a list of manual flight functions for your ATOM ITM Bluetooth-controlled helicopter. While you’re learning to fly your helicopter, it is best to start with a large room until you get used to the basic controls. As you master flying your helicopter you can move to motion control. Move the Throttle up to increase the speed of the main rotor and the helicopter will rise.
PAGE 5
FLYING TIPS UNDERSTANDING HELICOPTER TRIM ADJUSTMENTS If your helicopter over-rotates CLOCKWISE (to the right), push the LEFT trim button repeatedly until the turning stops and proper flight is maintained. If your helicopter over-rotates COUNTER-CLOCKWISE (to the left), push and release the RIGHT trim button in the same manner until the problem is resolved. From time to time you may have to adjust the left and right trim to ensure the helicopter will fly straight and respond accurately to control commands.
PAGE 6
HELICOPTER WARNING AND SAFETY PRECAUTIONS CONTENTS: The helicopter blades revolve at high speeds and can hurt the user, spectators and animals. Stand away from the helicopter to reduce the risk of getting into the flight path. Warn spectators that you will be flying your helicopter so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the helicopter.
PAGE 7
Replacing the Upper Propeller Blade Diagram 3 Diagram 4 Upper Blade Using a screwdriver turn counter clockwise to remove the screw. Diagram 5 Using the screwdriver turn clockwise to tighten the two screws. Remove the broken blade and carefully replace with a new one. Diagram 6 Diagram 7 Please note the design of the upper blade. When you tighten the screw you should test the blade to make sure that it still has free movement. Do not overtighten.