User's Manual

ManualsBrandsAsis Technologies ManualsElectronicsReader

AMR170 Series NFC Reader

User Manual

Document History

Description

Model

Original Release - Firmware version 1.0.7

AMR171,AMR175

Revised Oct 2013 Firmware version 2.1.2

AMR171,AMR175

Revised Jan 2014 Firmware version 2.13

AMR171,AMR175

Revised Apr 2014 Firmware version 2.15

AMR171,AMR175

Revised Jan 2016 Include FCC statement

AMR171,AMR175

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this equipment. (Example - use

only shielded interface cables when connecting to computer or peripheral devices).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

Summary of content (8 pages)

PAGE 1
AMR170 Series NFC Reader User Manual Document History Description Model Original Release - Firmware version 1.0.7 AMR171,AMR175 Revised Oct 2013 Firmware version 2.1.2 AMR171,AMR175 Revised Jan 2014 Firmware version 2.13 AMR171,AMR175 Revised Apr 2014 Firmware version 2.
PAGE 2
1.1AMR170 Series NFC Reader Overview The AMR170 Series NFC Reader is a new generation NFC card reader. The AMR170 Series NFC reader can read a wide range of contactless smart card covering single size UID card to double size UID card. Card ID data can be output via industry standard Wiegand or Asis Proprietary RS485. Both models are available to cater for various modes of security and operation needs.
PAGE 3
Note: Bit 7 CAN refer to Card Application Number found on Ez-Link card. Hex Address Bit Label 80 81 82 83 84 85 86 87 Bit 1 A0 0 1 0 1 0 1 0 1 Bit 2 A1 0 0 1 1 0 0 1 1 Bit3 A2 0 0 0 0 1 1 1 1 Bit4 A3 0 0 0 0 0 0 0 0 Bit5 1 1 1 1 1 1 1 1 Bit6 Bit7 Bit 8 Refers to Table 3 for other DIP Switch Setting.
PAGE 4
Figure 1 Physical Dimension Figure 2 Removal of Cover To remove the reader’s cover, unscrew the screw in the bottom and flip open the cover.
PAGE 5
1.5 Operation Guide The AMR170 series reader must work with the ACU controller (it cannot operate by itself). The reader allows user to access by Card only, Details of operation please refer to IBSS and/or ACU manual. Figure 4 Presenting Cards to Reader Keeping the card in parallel to the AMR17x reader a maximum read range can be obtained. The Reader will still be able to read Card when the card is presented at an angle but this will result in the reducing of read range.
PAGE 6
Access Grant Buzzer Beep once Green LED Blink once Granted Access Denied Buzzer Beep once Red LED Blink once Denied Access Invalid Buzzer Beep once Red LED Blink once Invalid Door Open Too Long Buzzer Beeping Door Force Open Buzzer Beeping Red LED Blinking DOTL Red LED Blinking Door Force Free Access Silent Green LED ON unlocked Door Locked Silent Red LED ON Locked Fire Activated Buzzer Beeping Red LED Blinking Fire Alarm Box Tamper Buzzer beeping Red LED Blinking Box-Tamper Pin M
PAGE 7
1.7 Product Electrical Specification Power Supply (Recommend) Regulated linear power supply, +12VDC, 300mA Operating Voltage Range +9VDC - + 24VDC Operating Current at +12VDC 85mA (average) – 185mA (peak) 150meters (500feet) Maximum Cable Distance (base on Belden 9538 24AWG 0.6mm, 8 core cable foilshield) (for wiegand interface) (base on Belden 9534 24AWG 06.
PAGE 8
Support Card Type Mifare ( ISO 14443-A, ISO 14443-B) EZ-Link Output CAN or CSN (Selectable) Mounting Hook On Bracket