Instructions for use Cooker hood CC4525S / 4000
EN Manual Pictograms used : Important information Tip EN 3 - EN 13
CONTENT Your canopy hood Description 4 Introduction 4 Use Controls 5 Maintenance Cleaning 7 Removing the grease filters 8 Replacing the carbon filter 8 Changing the light bulbs 8 Installation General 9 Electrical connection 10 Mounting the canopy hood 11 Technical specifications 12 Appendice Disposal of appliance and packaging 13 EN 3
YOUR CANOPY HOOD Description L T1 T2 T3 T4 S1 Switch lighting on/off Switch on/off + fan speed 1 Switch on fan speed 2/switch on carbon filter indicator Switch on fan speed 3/reset grease filter indicator Switch on intensive setting Filter indicator Introduction This user manual gives you a quick overview of all the possibilities offered by the appliance. You will find information on safety measures and maintaining the appliance. Please retain this user manual and the installation guide.
USE Controls Switching the fan on and off • Use the On/Off button (T1) to switch on the fan and select the extractor setting desired with the ‘T2’, ‘T3’ or ‘T4’ buttons. The LED indication on the buttons shows which setting has been selected. • Use the ‘T4’ button to switch on the intensive setting. • The intensive setting switches off automatically after 6 minutes. After these 6 minutes the speed is reduced to the setting previously selected.
USE Carbon filter indicator • Press and hold the ‘T2’ button for 3 seconds • to activate the carbon filter contamination indication. The LED indication on the ‘T2’ button flashes 2 times in confirmation. • After the extractor hood has been in use for 200 hours with the carbon filter contamination indication activated, the ‘S1’ indicator light starts to flash. This indicates that the carbon filter needs to be replaced. • Press and hold the ‘T2’ button again for 3 seconds to switch off the alarm.
MAINTENANCE Cleaning Attention! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket. The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Do not use abrasive products.
MAINTENANCE Grease filters Removing the grease filters Switch off the electricity! Remove the plug from the socket or switch the electricity off at the mains. Open the panel and pull the special handle to remove the filter. Replacing the carbon filter The carbon filter must always be used if the cooker hood is not ducted. 1. 2. 3. 4. Open the panel. Remove the grease filters. Fit the carbon filter by wedging it into the casing (B). Replace the filter grids in the extractor hood.
INSTALLATION General This appliance should be connected to the power supply by a recognized fitter who is familiar with, and works according to the correct safety regulations. This appliance meets the European requirements. Important that you know: • The minimum distance between the supporting surface for the cooking vessels on the gashob and the lowest part of the range hood must be not less than 65 cm. For use with an electric, ceramic or induction hob, this distance must be at least 50 cm.
INSTALLATION Electrical connection This appliance is manufactured in class I, it must therefore be connected to the earth system. Make sure the supply voltage ratings correspond with those stated on the appliance data plate. The connection to the mains is carried out as follows: BROWN = phase L BLUE = phase N YELLOW/GREEN = Earth During the electrical connection make sure that the electrical socket is equipped with earth connection. This canopy hood has been provided with a power plug.
INSTALLATION Montage • Open the panel. • Remove the grease filter. • Interrupt the plug connection of the controls. • First remove the 6 screws, followed by the frame. 0 500 25 - 840 26 • Use a saw to create a recess in the bottom side of the cupboard (at a distance of at least 650 mm from a gas hob). Refer to the measurement drawing for this. • Attach the unit with the 10 screws provided (12a). • Put the frame into position with the 6 screws. • Restore the plug connection of the controls.
TECHNICAL SPECIFICATIONS Hood type Type / Approval Control type Width Supply (Voltage, frequency) Power Power motor Power lights (W) Level 1 Air flow, Noise, Pressure Level 2 Air flow, Noise, Pressure Level 3 Air flow, Noise, Pressure Level 4 Air flow, Noise, Pressure EN 12 CC4525S Built in hood 4000 Electronic push buttons 60 220~240 V / 50 Hz 277 275 2 x LED 1W 330 m³/h, 53 dB(A), 320 Pa 500 m³/h, 64 dB(A), 420 Pa 575 m³/h, 67 dB(A), 440 Pa 680 m³/h, 72 dB(A), 490 Pa
APPENDICE Disposal Disposal of appliance and packaging By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The local authorities can provide you with the relevant information. The packaging of this appliance is recyclable. It could have been made from: • cardboard; • polythene foil (PE); • CFK-free polystyrene (PS-hard foam).
EN 14
FR 15
566263 566263 / VER 1 / 11-03-2016 566263