Technical data

ManualsBrandsAsko ManualsDishwasherD3250FI

Page 1

AUTOMATIC HIGH LOOP

The drain hose is fastened to

the back of the machine at

the best height. To eliminate

potential drain problems, leave

this hose in place.

IMPORTANT!

Read all of these instructions

before installing the dishwasher.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Introduction 2

What You Need 2

Dimensions 3

Preparing the Location 3

Water Supply 4

Drain Connections 5

Electrical Connections 6

Preparing the Dishwasher for Installation 6

Moving the Machine into Place 7

Connecting the Electric Cable 8

Connecting the Water Supply 8

Adjusting the Leveling Legs 8

Fastening the Dishwasher to the Cabinet 9

Installing the Toe Kick 9

Fitting the D3250 and D3530 Custom Door Panel 10-11

Index 12

CONTENTS

ASKO

DISHWASHER

INSTALLATION

INSTRUCTIONS

Summary of content (12 pages)

PAGE 1
ASKO DISHWASHER INSTALLATION INSTRUCTIONS NT! tructions A T R O P IM ins asher. f these w ll o the dish Read a g n i l l a t ins before AUTOMATIC HIGH LOOP The drain hose is fastened to the back of the machine at the best height. To eliminate potential drain problems, leave this hose in place.
PAGE 2
INTRODUCTION Read these instructions carefully and completely before you install the machine. The installation should be carried out by a qualified person who is familiar with all local codes and ordinances for electrical and plumbing connections. If a dishwasher is being installed in this area for the first time, most of the cabinet work, plumbing, and electrical has to be done before you move the machine into place.
PAGE 3
DIMENSIONS UNIT DIMENSIONS Height Width Depth Weight US Measurements Metric Measurements 32-1/4"–35-1/2" *24" 23-5/8" 106 lb 819–902 mm 610 mm 600 mm 48 kg 46-5/8" 1184 mm 24" 610 mm 6-1/4" - 8-1/4" 159 - 210 mm 32-1/4 to 35-1/2" 819 to 902 mm 23-5/8" 600 mm Door 6-1/4" 159 mm 2" 50 mm 2-1/4" 57 mm *Models D3250FI and D3530FI are 23-5/8” wide. PREPARING THE LOCATION The best place for your dishwasher is in the kitchen near the sink.
PAGE 4
CORNER INSTALLATION If the dishwasher is installed in a corner, there must be a minimum clearance of 2” (50 mm) from the side wall so the door can open. INSTALLING THE TIP GUARDS (OPTIONAL) When it is not possible to fasten the dishwasher to the cabinet, you should install tip guards to prevent the machine from tipping when the door is opened. The tip guards can be attached either to the floor or the wall.
PAGE 5
DRAIN CONNECTIONS ASKO provides a 7/8” (22 mm) corregated drain hose which is connected to the back of the unit to form a high loop. If additional drain hose is needed, please purchase an additional ASKO drain hose and joint it to the provided hose with a 7/8” (22 mm) copper tube. NOTE: Do not use any fittings anywhere in the drain line that are less than 7/8" (22 mm) ID. THREE WAYS TO INSTALL DRAIN CONNECTIONS A.
PAGE 6
ELECTRICAL CONNECTIONS WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Do not use an extension cord for this appliance. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. WARNING! Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or other local electrical codes.
PAGE 7
MOVING THE MACHINE INTO PLACE WARNING! Make sure you put the protective slides on the legs to prevent damaging the floor when you slide the unit into place (see page 6). 1. Position the machine in front of the cabinet opening. 2. Make the height adjustment while the dishwasher is in front of the opening. 3. Pull out the drain hose to ensure there are no sharp bends. 4. Start to feed water and drain lines and electric cord (if necessary) into the access hole in the cabinet. 5.
PAGE 8
CONNECTING THE ELECTRIC CABLE If the cord is not long enough, or if a hard-wire installation is needed, follow the steps below to complete the electrical connection. WARNING! Before starting this procedure, be sure the power is turned off at the breaker/fuse box. 1. Connect supply cable with a UL-listed strain relief bushing (if nonmetallic cable is to be used). 2. Connect branch circuit white lead to N lead on filter. 3. Connect branch circuit black lead to L lead on filter. 4.
PAGE 9
ADJUSTING THE LEVELING LEGS Now that all the connections are made and the machine is in place under the cabinet, you should make the final height adjustment. 1. You should set the rear foot first. To do this, use a screwdriver to rotate the adjusting screw on the bottom front of the machine. Turn the screw clockwise to raise the foot and anticlockwise to lower it. 2. Using a 1/2” (12 mm) wrench, adjust the locking nuts until the machine is level.
PAGE 10
FITTING THE D3250FI AND D3530FI The D3250FI and D3530FI can only be installed with a fully-integrated custom door panel that extends from the toe kick to the counter top. The unit comes with everything needed to make installing the door panel easy. The door is predrilled for the panel’s mounting screws. The custom panel can be a minimum of 1/4” (6 mm) thickness to a maximum of 3/4” (19 mm) thickness.
PAGE 11
D3250FI AND D3530FI OPTIONS CUSTOM PANEL INSTALLATION 4-inch Toe Kick Installations Custom panels the same height as the dishwasher door If the custom panel is the same height as the dishwasher door, a 2” (51 mm) decorative fill strip or pull-out cutting board must be used to fill the area between the panel and the counter top (as illustrated below).
PAGE 12
INDEX A Access holes S 3 C Cabinet, fastening unit to Cabinet opening dimensions Connecting to water supply Corner installation Cosmetic damage 9 3 9 4 2 3 11 10 4 E Electrical cable connection Electrical connections European installations 6 T D Dimensions, unit Door panels, fully-integrated Door springs, adjusting Drain connections Slides for rear legs 8 7 3 Technical data Tip guards installing 4 Toe kick installation options on FI units installing Tools 2 2 11 9 2 U Unit dimensions 3 W Wate