Version 1.0 2009.06.
CONTENTS " What is Drum Washing Machine? ...........................................................3 " Washer Specification . ..............................................................................6 " Operating Mechanism Diagram ..............................................................7 " Parts List By ASS’Y ..................................................................................8 " Control Part Function Spec ...................................................................
" What is Drum Washing Machine? 1. Drum Washing Machine Water consumption is reduced by using the power of the laundry falling (free-fall) created when rotating the drum resembling a sieve net. With temperature control system, this drum washing machine saves energy and improves washing performance at the same time. 2. Key Features " Simultaneous supply of cold#hot water As cold and hot water is supplied at the same time, heating time and energy is saved.
3.
rum Wa 4. Major Functions $ Washing When rotating drum after putting in the laundry and detergent into the drum, the laundry are rotated by protrusions (lifters) attached inside the drum. Washing is carried out with bending and impact actions generated by falling of the laundry to the top part of drum. % Rinsing Rinsing cleanly washes out detergent and dirt removed from the laundry after washing cycle. & Spin-drying Weak, standard and strong cycles can be selected according to types of fabrics to be washed.
" Washer Specification 1. Product Specification External Measurements (inches) 27"(width) x 31.8"(depth) x 40.1"(height) Weight 198.4lbm Rated Supply Power Rated Consumption Power 120V 60Hz Washing 200W (1100W during heating) Washing Method Drum type Water Pressure Water Pressure 29kPa ~ 784kPa(0.
" Operating Mechanism Diagram 4. WATER SUPPLY PART • Cold Water: 3 holes Cold water, pre-washing • Hot Water: 1 hole • Water supply box, hose Electricity Input Noise Filter Water Supply Program 1. CONTROL PART • Main PCB • Front PCB • Harness • Noise filter • Power Cord: 15A Delergent Container Thermister Drum Door BLDC Motor 2. DRIVING PART • BLDC motor • Drum • Bearing • Spider/ shaft • Tub • Weight balancer Door Switch 5.
" PARTS LIST BY ASS’Y 1.
No. - Part Name CABINET SUB AS Part Code Qtt'y Specification 3610811950 1 13KG, PUMP, WHITE WL6532 XXLW, XXLW RH 3610811955 1 13KG, PUMP, PLATINUM WL6532 XXLPP 3610811956 1 13KG, PUMP, ROSE RED WL6532 XXLRR 3610811957 1 13KG, PUMP, BLACK WL6532 XXLBB • 1PIECE SVC PART C01 CABINET 3610811740 1 SGCC 0.8T PUMP WASHER C02 FRAME LOWER 3612206700 1 SBHG 1.2T C03 FRAME TOP L 3612206500 1 SGCC 1.6T C04 FRAME TOP R 3612206600 1 SGCC 1.
rum Wa 2. BASE U ASS'Y B06 B02 B01 B03 B04 B05 No. Part Name Part Code Qtt'y Specification Remark B01 REACTOR 52G043A110 1 RT-047K L=150 B02 BASE U 3610392700 1 PP B03 SUPPORTER LEG 3615303600 4 PO+Coating 3.0T B04 FIXTURE LEG 3612006400 4 ABS, DWD-100DR B05 FOOT AS 3612100700 4 Foot+Special bolt, Double insert type Hybra-Nylon66 B06 PROTECTOR HEATER 3618304600 1 SECC 0.
3.
rum Wa No. Part Name Part Code Qtt'y Specification T01 SPECIAL SCREW 3616029400 8 SWCH 8.5 x 30 T02 BALANCER WEIGHT AS(L) 3616110100 1 13kg DRUM BALANCER WEIGHT AS(R) 3616110200 1 13kg DRUM T03 GASKET AS 3612322000 1 EPDM, Wash-only, Nozzle shower T04 NOZZLE SHOWER 3618104000 1 PP T05 CLAMP GASKET AS 3611205300 1 Gasket, 13kg Drum T06 TUB FRONT 3618828Y00 1 FRPP, 13kg Drum T07 SPECIAL SCREW(TUB) 3616029800 15 SWCH 6.
4. INLET BOX AS No. Part Name Part Code Qtt'y Specification Remark I01 INLETBOX 3617510800 1 PP I02 NOZZLE AS 3618104800 1 Top+Under I03 HOSE INLET 3613270300 1 EPDM I04 CLAMP AS 3611203200 2 ID=60, WIRE+GUIDE+BOLT+NUT I05 HOSE WATER SUPPLY 3613270920 1 EPDM ID=9.5 OD=15.5 L=410mm I06 HOSE WATER SUPPLY 3613270920 1 EPDM ID=9.5 OD=15.5 L=380mm I07 HOSE WATER SUPPLY 3613270920 2 EPDM ID=9.5 OD=15.5 L=230mm I08 HOSE WATER SUPPLY 3613270920 1 EPDM ID=9.5 OD=15.
5.
No. Part Name F01 CABINET F SUB AS Part Code Qtt'y Specification Remark 3610811310 1 13KG, PUMP, WHITE WL6532 XXLW, XXLW RH 3610811321 1 13KG, PUMP, PLATINUM WL6532 XXLPP 3610811322 1 13KG, PUMP, ROSE RED WL6532 XXLRR 3610811324 1 13KG, PUMP, BLACK WL6532 XXLBB F02 SUPPORTER HINGE 3615304001 1 SGCC 1.
6.
No.
7. PLATE T ASS'Y T02 T01 T03 No. T01 T02 Part Name Part Code Qtt'y Specification PLATE TOP AS PRMACA3R00 1 SECD 1.
rum Wa 8. ACCESSORY A01 No. Part Name A01 HOSE DRAIN O AS A02 Part Code A03 Qt'y Specifications A04 Color Cost in USD($) A05 Remarks 3613268500 1 DWD-800W, L=1,500 NA 3612502300 1 PP NA A02 HOSE INLET AS 3613271500 1 REFLEX, PVC 1.3M NA Cold HOSE INLET AS 3613271510 1 REFLEX, PVC 1.3M NA Hot A03 UNIT SVC WRENCH 36189L3X00 1 PO+Coating, 2.
" Control Part Function Spec 1.
rum Wa Classification P r e W a s h W a s h R i n s e S p i n End Sensing Water Supply Pre-Wash Drain Balancing Spin Middle Spin Sensing Water Supply "Main-Wash 1 (Heating)" Drain Balancing Spin Middle Spin Water Supply Rinse 1 Drain Balancing Spin Middle Spin Water Supply Rinse 2 Drain Balancing Spin Middle Spin Water Supply Rinse 3 Drain Balancing Spin Spin Processing Time 10sec 2min 10min 8min 1min 2min 3min 20sec 2min 50min 45min 30min 25min 15min 1min 2min 3min 2min 4min 1min 2min 3min 2min 4min
2. Composition per Function 2-1. Water Supply 1) Water Temperature Selection Water supply algorithm differs according to water temperature selected among 5 levels. In other temperatures, with the exception of cold water, constant temperature control is executed. Cold water and hot water operation is carried out in turn according to the target temperature. Water Temp. Target Temp.
rum Wa 2-2. Drainage 1) Pump Operation - Washing cycle $ Before Drainage Completion: Pump continuously on % Spin-drying Cycle after Drainage Completion : On for 18sec and off for 3sec 2-3. Sensor Detection 1) Water Level Sensor Data Classification Height Frequency (mm) (KHz) Spec. Small 130 24.62 Spec. Low 130 24.62 Washing Small 130 24.38 Washing Low 130 24.09 Standard Rinsing 160 24.27 Rinsing 160 23.64 Additional Rinsing 175 24.01 Tub Washing 195 23.77 Overflow 260 22.
2) Temperature Sensor Data Temp. *) Resistance(* Voltage 0 35.97 0.58 10 22.76 0.86 20 14.77 1.21 22 13.57 1.29 24 12.48 1.37 25 11.98 1.41 27 11.04 1.49 29 10.18 1.58 30 9.78 1.62 32 9.04 1.71 34 8.36 1.80 36 7.74 1.89 38 7.17 1.98 40 6.65 2.07 49 4.7 2.50 55 3.85 2.75 60 3.24 2.96 65 2.74 3.16 75 1.99 3.
rum Wa 2-4. How to Control Voltage (during abnormal operation) 1) Voltage Control $ Normal Voltage DC-link voltage after wave rectification is directly impressed to IPM as 310 ~ 330V. When motor starts operation, DC voltage changes with energy consumed by motor and/ or counter electromotive force of motor. % Identifying Abnormal Voltage A. Occurrence of counter electromotive force + In case of 450V or higher B. Instant power failure and excessive energy consumption + In case of 185V or lower 2-5.
2-6. Door S/W 1) Door S/W Operation $ Door Locking 3sec after bi-metal operation of door S/W, pulse of 20msec duty on solenoid is impressed twice until door is locked. Bi-metal begins operation simultaneously as power button is pressed. % Door Unlocking Bi-metal plate of door S/W is turned off and pulse of 20msec duty on solenoid is impressed until door is unlocked. & Motor or other electronic parts begin operation to execute normal cycles only when door is locked.
rum Wa 2-7. Load Sensing 1) Load Sensing to Determine Water Level $ Á Load sensing is carried out when selecting standard, boiling and thrifty boiling courses. % Sensing is administered in the dry laundry state before starting of washing cycle. & After motor operation at 75 r.p.m for 10sec, load is judged with motor output measured. 2) Load Sensing for B Spin-drying $ Sensing is administered with the laundry wet during the first interim spin-drying after completion of washing cycle.
3. Functions per Cycle 3-1. Washing Cycle 1) Classification of Washing $ Pre-washing and soaking are carried out before main washing cycle. % Decided value refers to water level and time decided by load sensing in standard, boiling and thrifty boiling courses. In other sources, it means the pre-set time according to the designated water level. & Soaking is the cycle consisted with water supply and washing only. Main washing begins immediately after this cycle without drainage.
rum Wa 3-2. Rinsing Cycle 1) Water Supply Cycle $ When selecting 'add water for rinsing', water is supplied to the water level of additional rinsing. % Only cold water is supplied in rinsing cycle. & In the last rinsing, fabric softener is inserted by opening both cold water V/V and pre-washing V/V at the same time. 2) Re-supply of Water $ Water level is checked 1 minute after starting of rinsing cycle. Then, water is re-supplied up to the designated water level.
3-3. Spin-drying Cycle 1) Drainage $ Drainage set time is 1min. % When drainage is completed, 1 minute is reduced from the overall cycle. 2) Balance Spin-drying $ Spreading the laundry : Rotating the same 45rpm with left and right direction altematively. % Attaching stop : Attaching the laundry to drum inside with constant speed. & Unbalance checking point : First step, check the U.B at 95 rpm, 160rpm Second step,check the U.B at 95 rpm, 350rpm Third step, at 300rpm.
rum Wa 3-4. Ending 1) Untwisting $ This cycle aims to prevent creasing by loosening the laundry attached to the inner wall of drum after completion of spin-drying. Untwisting is carried out for 30sec. % Motor is operated according to the water stream of untwisting. 2) Ending $ After completion of untwisting, buzzer is sounded for 10sec and power is turned off. % In case additional drying cycle has been set, drying cycle is carried out after untwisting. & After ending process begins, door lock is cleared.
4. Button Functions 4-1. Power 1) This electronic power switch turns on/ off display. 2) Automatic Power Switch Off $ Power is turned off immediately after completion of entire cycles or the selected cycle. % Power is automatically turned off in 10 minutes if no button control is made after power on. 3) Initial Display for Power Only $ Course LED is turned on for 1sec. % 18:88 LED displays '---'. 4-2. Start / Stop 1) Normal course begins when pressing button after turning on power S/W.
rum Wa 4-3. Wash 1) Range of temp. selection differs according to the course selected. If you select Cold, the washing temperature will be the same as that of the machine's water supply. Each program the temperature it will be able to select is restricted. (Refer to Washer Program Default Data and Select Option.) 2) The text displayed indicates water temperature for washing. "Cold water is used for rinsing. When ‘Warm*’ is selected, warm temperature is maintained for both washing and rinsing.
4-5. Spin Speed 1) When pressing button, LED is repetitively lit in the order of " Medium. High. Extra High . Off. No Spin. Low'. 2) 18:88 display shows the remaining time. 3) During cycle, selection change is possible after temporary suspension. 4-6. Signal 1) Signal button operates in 5 steps. Press Signal to adjust the sound level or turn off the signal. 2) After change, it is saved in EEPRPM. 4-7. Pre-Wash 1) Button is operated only when washing is selected.
rum Wa 4-8. Extend Wash 1) When button is pressed, washing time increases per washing course, such as by 6 minutes for 'heavily', 8 minutes for 'sanitary', 5 minutes for 'everyday wear' and 'towel' and 4 minutes in other cases. 2) Extra wash is not available in Silk/Gentle, Quick Wash, Wool/Handwash courses. 3) Extra wash LED is turned off when washing is completed. 4-9. Extra Rinse 1) Extra rinse is not available in Quick wash courses. 2) When pressing button rinsing cycle is added by once and LED is lit.
4-10. Night Time 1) When pressing button, spin speed is set as low and interim spin-drying changes from 790 r.p.m. to 550 r.p.m. 2) When pressing button again, set values of interim spin-drying and main spin-drying mode courses are resumed. 3) LED is turned off when the cycle is completed. 4-11. Delay Start 1) Preset time indicates starting time of the entire cycle. 2) When pressing preset button, time changes in the order of 1.2.3. 4 ….12.1.
rum Wa 4-13. Course Selection Switch 1) Everyday Wear course selected by clicking switch once after power is turned on. 2) Per each click after the first, course is selected in the direction of CW or CCW. 3) 18:88 display indicates cycle time of each course. 4-14. Washer Program Default Data and Select Option Heavily Sanitary Bulky Everyday White Synthetic Towel Silk Quick Wool Temp Soil Spin default Warm* Normal High selection Cold~Hot Ex.light~Ex.heavy no spin~Ex.high default Ex.
rum Wa 5. PCB Manual Test Mode - PCB and other electronic parts will be tested without water supply whether they are normal or not. 1) Process : Press power button -> Press "SPIN" button 3 times with pressing "WASH" button -> "X X X" will be shown on LED display-> Whenever pressing "Signal" button 1 time, below process will be occurred. - "X X X' : Program version display Step Display Details " #$% &''(!#')*!%+',- . (/0 11" 7 8" 1 9:##;<=>
6-1. IE (Input Error) - Error in water supply 6-1. IE (Input Error) - Error in water supply 1) Conditions of Occurrence $ In case the designated water level is not reached in 5 minutes during water supply or re-supply 2) All LEDs are turned off and 'IE' blinks in18:88 display. 3) Error buzzer alarm is sounded for 10 seconds per every 10 minutes. 4) Error display is cleared when turning off/ on power. 6-2.
rum Wa 6-4. LE (Lock Error) - Door opening error 1) Conditions of Occurrence $ When intending to begin cycle by pressing start/ temporary stop button while door is opened 2) All LEDs are turned off and 'LE' blinks in 18:88 display. 3) Error buzzer alarm is sounded for 10 seconds per every 10 minutes. 4) Error display is cleared when turning off/ on power. 6-5.
6-7. E4 - Water leakage during washing 1) Conditions of Occurrence $ In case water level falls below re-supply even after 15 times of re-supply prior to finishing of water heating 2) All LEDs are turned off and 'E4' blinks in 18:88 display. 3) Error buzzer alarm is sounded for 10 seconds per every 10 minutes. 4) Error display is cleared when turning off/ on power. 6-8.
rum Wa 6-9. Motor-related Error 1) E5 (DC-Link High Voltage) Error $ In case DC-link voltage to IPM increases to 450V or higher % Motor operation is stopped and 'E5' is shown in display window. & Error buzzer alarm is sounded for 10 seconds per every 10 minutes. ' Error display is cleared when turning off/ on power. 2) E6 (EMG) Error $ In case current detected with EMG port is of 20A or higher % Motor operation is stopped and 'E6' is shown in display window.
3) H5 Error - Water temperature error in wool/ delicate course $ In case water temperature in wool/ delicate course is 45) or higher % Error buzzer alarm is sounded for 10 seconds per every 10 minutes. & Error display is cleared when turning off/ on power.
" PCB PIN ARRANGEMENT 44
"Detailed Spec, Principles and Breakdown Diagnosis/ Service of Electronic parts 1.
rum Wa Water supply not carried out (IE) Defect in Water Supply Continuous water supply (IE) • Suspension of water supply • Tap frozen • Tap closed • Hot & cold water hose switched for connection • Low water pressure (0.
Symptoms of Inspection Spot Breakdown Water supply not carried out Inspection Method Inspection Result Problem Identified 1) Suspension of water supply 2) Water tap locked 3) Cold-hot water hose incorrectly - Cold/ hot water hose switched -Defect in cold/ hot water connected -Large amount of rust, sand and hose assembly 4) If no defect is found, dismantle water dust, etc. -Defect in cleaning of water supply hose and check water supply supply filter (blocked) valve filter.
rum Wa #$!Water Level Sensor 1) Spec. of Water Level Sensor O/F: Forced drainage is necessary as water level is high. When this level is reached, water supply must be stopped and drainage must be forcefully administered. RESET : Low: Small load of laundry, therefore considered to be water level of 'low' 1. Spin-drying begins 30sec after drainage level reset is reached. Medium: Large load of laundry Medium High: Water level for rinsing 2.
Defect in Water Level Detection E9 • Defect in pressure sensor • Defect in PCB • Defect in water level detection circuit • Water supply greater than the selected water level • Continuous water supply in high water level • Pressure sensor hose bent or partially blocked • Defect in pressure sensor • Air leakage from pressure sensor hose • Defect in water level detection circuit • Water supply smaller than the selected water level • Reset level not detected • Foreign substance in air trip inlet • Water
rum Wa %$!POWER CORD Classification Rated Cord Thickness Color Code Type Length Remarks DEC 250V/15A 1.5sq Gray 3611340430 LP-31 SJT 2.3m - 1) Assembly 4 embossed parts in cabinet -> To prevent loosening after assembly -> SS: 2 special screws -> LG: Forced indentation [Before] [After] .
&$! DOOR LOCK S/W 1) Comparison of Door Lock S/W Spec. TYPE CODE MODEL RATED LOCK ON PRINCIPLE LOCK 'ON'/'OFF' TIME LOCK OFF TYPE EXTERNAL APPEARANCE DF F01 007 3619046410 WD1132 125V 16A Bimetal operation -ON : Min. of 6sec 1. Forced OFF by by PTC heating -OFF after Cooling solenoid in Air: 40sec ~ 5min 2. Natural OFF by -Forced OFF: cool down of Immediate OFF (door opening) bimetal 2) Structure and Spec. of Door Lock S/W: DF SERIES 1.
r * How to Replace Door Lock Switch 1) Open door and dismantle clamp spring for gasket. 2) Dismantle gasket. 3) Loosen 2 screws for door lock S/W. 4) Remove door lock S/W. 5) Administer assembly in reverse order. * Checking Solenoid Wiring of Door Lock Switch PIN Arrangement 2345 (1 does not exist.
[ Operation Procedures ] : When door is closed 1. Initial Status: Door opened [ FIG 3] 2. Door Closed: Slider moving by door hook as shown in [FIG 4] 3. Turn PCB power button on to enter power and push start button. 4. PTC begins heating as power is entered to No. 1 and 3 in [FIG 2]. 5. Deformation of [UPPER BIMETAL] begins due to PTC heating. 6. Deformation of upper bimetal moves PTC and PTC moves blade.
4) Diagnosis of Defect Symptoms Detailed Symptoms Cause Diagnosis of Defect Solution Ticking noise Tick' during initial operation and 'tick-tick' during temoprary suspension: 'DF' type only Normal noise Normal sound generated during solenoid operation when 'sliding CAM' is locked/ unlocked to close or open door. LE' Continuous occurrence of 'tick' noise and 'LE': 'DF' type only Connector loosened Visually checking connector connection status 1.
r '$!HEATER 1) Spec of Heater of Washing Machine Classification Wahing Maker IRCA Rated 120V Consumption Power 1000W15% Resistance 25.47ohm Current Density 8.9 Temp. Fuse 184) Washing Heater Thermister Heater built-in Washing Temp. Sensor MaterialSUS430 Max. Temp. Water Part Code 3612801740 Temp. Fuse of Washing Heater (184°C CUTOFF TYPE) : Located inside heater to prevent fire, etc. caused by heating without water due to breakdown of water level sensor, etc. : Cut-off in app.
r 2) Breakdown Diagnosis Breakdown Symptoms Solution PCB Error Mode Check for short: DWD-11'S, no detergent, 800W common Connect the cut-off part. "H6" Check for short: Normal if 23.3~25.7ߟ between both terminals of washing heater -> Common for drum Replace washing heater. "H6" Connector/ terminal loosening Check for loosening: Common for drum Insert terminal. "H6" Defect in washing heater temp. sensor Measuring resistance between both terminals of sensor: Replace temp. sensor.
($!)*+,!-./.0 6-1. Structure of BLDC Motor 6-2.
r (1%$!234567658/6.9 Classification 1. General 2. Performance 3. Structure Item BLDC : DD Motor Rated Voltage Vm = 310 [Vdc], Hall IC Voltage 5 [Vdc] Insulating Structure Type B, insulator method External Appearance Shaft connection and stator connection structure, Air-gap : 1mm No. of Poles 24 poles, Core: 36 slots, Layer: [30mm] Consumption Power 390[W]±10[%], during washing (picked value) RPM During Washing: 45RPM, During Spin-drying:1300RPM Output Characteristics Torque: 300Kgf.
:$!;<=3!+08698>4!2?@/4= Drainage Hose Direction of pump filter cap opening Wire connection terminal Pump filter Defect in Drainage Drainage not carried out (OE) • Pump case blocked (coin, foreign substances, memory wire) • Pump case frozen • Defect in pump operation • Drainage hose pressed down or position changed • Ends of drainage hose blocked (built-in installation) • High edge of drainage way: Natural drainage/ • Product frozen (drainage way frozen) • Loosening of drainage motor connection terminal
Power Part Problem in indoor wiring • Breakdown of power lead-in switch • Indoor wiring fuse short • Aging of power outlet, defect in contact • Extension cord short or too thin Problem in wiring of washing machin • Power cord short (defect in contact) • Lead wire short • Controller terminal segments and connector loosened • Defect in contact of electric wire connector (power switch, reactor) • Breaking of insulated wire in lead wire terminal compression part Defect in electric parts • Fuse short: In n
A$!B.6@4!+4745/ Noise Hammering sound from drum during initial operation • Bolt for transportation not removed • Defect in leveling adjustment • Ground surface not flat • Weak ground (wooden board, frame made with angle and Styrofoam, etc.) • Loosening of spring • Spin-drying small quantity of laundry (bath towel, jeans, etc.) • Belt damaged Vibration and noise when spin-drying reaches normal r.p.
" Wiring Diagram 62
" Installation 1) Related Parts and Configuration Item Configuration Remarks FIXTURE UP / DOWN AS SPECIAL SCREW UP : L= 109mm SPECIAL SCREW UP FIXTURE DOWN FIXTURE UP SPECIAL SCREW DOWN :L=160mm SPECIAL SCREW DOWN % REMOVE FIXTURE UP/DOWN AS UNIT SERVICE WRENCH & ADJUST LEG FIXTURE LEG LEG ADJUST AS FOOT 2) Installation Procedures % Remove fixture up/ down AS. Removal Remarks ' Remove fixture up/down AS by rotating it in anti-clockwise direction. ' Store fixture up/down for use later on.
r & Insert cap holder (4) into holes created after removing fixture up/down AS as shown in the picture. CAP HOLDER ( Install drum washing machine on flat and solid ground. * Adjust leveling with led adjust AS. Adjustment Remarks ' Washing machine is moved upwards by rotating foot of leg adjust AS in clockwise direction. ' Washing machine is moved downwards by rotating foot of leg adjust AS in anticlockwise direction ) Adjust fixture leg to fasten special bolt.
"Reversing the door 1. Open the door and remove the door by unscrewing 4 bolts holding the hinge. 4. Unscrew the 2 screw on the s/w door lock on the right side of the door and draw out the s/w door lock. 2. Remove the clamp gasket ass'y 5. Draw out the hinge on the left side of door and detach the label on the right side. And attach the RH type label on the left side of door 3. Draw out the shower hose and fix the gasket toward the inside of drum. 6.
7. Then insert the socket of door lock as following figure. And secure the gasket and clamp. 8. Separate the stopper door by unscrewing 1 screw. Then rotate the door glass 180°C and secure the stopper door you removed. 9. Secure the hinge using the bolts you removed in step 1.
"DISMANTLING METHOD PER WASHER ASS'Y INLETBOX ASS'Y 1 2 PANEL FRONT ASS'Y 1. Remove 2 screws. 2. Remove panel F. 3. Remove connector. 4. Take caution for damaging hook.
PLATE TOP ASS'Y 1. Remove 3 screws. 2. Remove 4 screws.
BOX INLET ASS'Y 1. Remove 4 hose clamps. 2. Remove 1 screw and separate inlet box. 3. Remove and separate hose inlet.
VALVE 3WAY 1. Remove 4 screws. 2. Separate 3 connectors. 3. Separate 3 hose clamps.
MAIN PCB ASS'Y 1. Separate harness and separate PCB cover. 2. Separate connector. 3. Remove 1 screw.
WATER LEVEL SENSOR 1. Remove 1 screw. 2. Separate connector. COVER BACK 1. Remove 4 screws. 72 3. Separate pressure sensor hose.
MOTOR ASS'Y 1. Remove 1 bolt to fix stator. 2. Remove motor by separating 6 bolts to fix rotor. (Caution for damaging guide pin) WASHING HEATER 1. Unfasten nut. 2. Remove connector. 3. Remove heater in the direction of arrow. DAMPER ASS'Y 1. Press the projected edge of sharp part in damper pin. 73 2. Remove damper pin.
3. Remove damper pin on tub side in the same way and remove damper. FILTER DISMANTLING (1st Lifter) 1. Push filter in the direction of arrow and pull it out by lifting it in upward direction.
CABINET FRONT ASS'Y 1. Remove clamp gasket. 2. Remove 4 screws. 3.Saparate cover and case pump. 4. Remove 1 screw. 5. Lift front in the direction of arrow to open it in forward direction. 6. Separate door switch connector.
DRAIN PUMP ASS'Y 1. Remove drain hose clamp. 2. Remove 1 screw. 4. Remove pump in the direction of arrow. 76 3. Separate connector.
DOOR LOCK SWITCH 1. Remove 2 screws and separate door lock switch. DOOR ASS'Y 1. Remove 4 screws. 2. Dismantle door after removing 16 screws to fix frame door I.
TUB ASS'Y 1. Separate weight balancer after removing 8 screws. 2. Separate motor ass'y 3. Separate tub front after removing 16 screws, 2 sping suspension, 4 damper pin on Base under, Hose Air(T22), Hose Drain(T13) Hose air pressure(T15) and Harness AS on tub rear.
