User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Version: 1.01 © Copyright 2005. Asoka USA Corporation. All rights reserved. Asoka USA Corporation reserves the right to modify product offerings or specifications without advance notice. No part of this publication may be produced in any format without the express written permission of Asoka USA Corporation.
FCC Caution: 1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP 1. Introduction .............................................................................................................. 4 1.1 Features............................................................................................................... 4 1.2 Package ............................................................................................................... 4 2. Hardware Installation ....................................
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Technical Support You can download latest software from our website. If you have any question or difficulty during installation or using PlugLinkTM PL9550-WAP, please contact our technical support engineer. About User’s Manual User’s Manual of PL9550-WAP is released in December, 2005, the version is 1.01. This manual illustrate how to installation and configure PL9550-WAP.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Introduction Thanks for your selection of AsokaUSA PlugLinkTM PL9550-WAP. We are devoting to provide powerful, high-performance and applied power line networding system. The product is designed for home, hotel, office, apartment . It provides a full local network solution with PLC technical. 1.1 Features Complies IEEE 802.3, IEEE 802.3u, IEEE802.3x, IEEE 802.3z/ab standards Support both 802.11b and 802.11g wireless standards IEEE 802.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP 2. Hardware Installation 2.1 The Front Panel 2.2 Connect Device and PC a. Plug the wireless AP into a electrical outlets. b. Connect the wireless AP to a PC or Laptop with CAT5 cable through RJ45 port. d. Set network configuration of PC to communicate with the wireless AP. The default IP address of the wireless AP is as below: Default LAN IP address: 192.168.1.254 e.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Figure 1. system login The default User ID is “admin” and the default Password is “welcome”. Please remember to modify User ID and Password after you login successfully first time. 3.2 System System configuration provides interface to view the general configuration and status and set general configuration of the device including Date & Time, Password & User ID etc.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Figure 2. system details From the page, we can find that there is one main menu in the upper part for configuration. The submenu in the left part of the page show all items for each menu selected.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP The upper form shows how to change system user ID and Password Input old user id in the first text box Input new user id in the second text box (input old user id means keep user id without change ) Input current password in the third text box Input new password in the fourth text box Reinput new password in the fifth text box Click button ‘Apply’ begin set new user id or password, then a new page will show the result of the setting 3.2.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Figure 5. System Reset To reset system, click button “System Reset”. If you confirm your decision, please wait a minute for the system reboot. To restore the factory setting to the gateway, click button “Factory Default”. If you confirm your decision, please wait a minute because the system should be rebooted. 3.2.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Figure 7. Firmware upgrade Click button “Browser” to select firmware file, then one windows dialog will be popped up for user to select local file Check the ‘clear old configuration’ box to clear old configuration saved in the device and restore with factory default during upgrade. Click button “Update” to begin update. If you confirm your decision, it will update the firmware and reboot the device, the process will cost about 2 minutes.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP The screen contains the following details. Wlan Interface: To enable or disable wireless part of the device. Select the check box to enable wireless function. Channel Id: Identifies the channel on which the AP communicates. Each wireless client must use the same channel to enable communication. This can only be altered from a PC that is wired directly to the AP, not wirelessly.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP Figure 9. Wireless Security The screen contains the following details. Encryption Type Determines the type of security encryption algorithms for the key index. This security setting encrypts your wireless transmission. None, WEP are available only when Open System or Pre-shared KEY (PSK) is selected for authentication type. TKIP and AES are available only when WPA and WPA-PSK (PSK) are selected. The default type is None.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP 3.4.1 IP Address To configure the IP Address of the Wireless AP, click on the link IP Address in the left submenu, a screen is displayed as shown in Figure 11. Figure 11. IP Address Configuration The screen contains the following details: IP Address: Subnet mask: To enter the IP address of the Wireless AP the subnet mask Click button “Apply” to save the configuration and renew system IP address. 3.
Asoka® User’s Guide PlugLink 9550 Wireless Access Point PL9550-WAP link Device Scan in the left submenu, a screen is displayed as shown in Figure 13. Figure 13. Scan devices The screen contains the following details. Scanned Devices: The No. of the device have been scanned MAC Address: The MAC address of the device in the same power line network Click button “Scan Now” to refresh the device list.
