Installation Guide
Outdoor
Wall Fixture
Model: 326916
& TPWW70050LWH
1 of 1
Limited Factory Warranty
American Fluorescent Corporation warrants this fixture is
for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de
not cover failure due to improper installation, misuse, mishandling or damage incurred in transit
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with
instructions could result in potentially fatal electric shock and/or
property damage.
It is recommended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not
handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
ASSEMBLY INSTRUCTIONS
1.
Preparing for installation
A.
Disconnect electrical power
B.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
misplace any of the screws or parts
2. Wiring-
all wiring must take place inside junction box.
Caution:
Make sure power is off at fuse or circuit
breaker box. Check power wires for damage or scrapes.
If power supply wires are within three inc
ballast power supply
, use wire suitable for at least
(194F). Note:
Most dwellings built before 1985 have
supply wire rated to 60C. Consult a qualified electrician
before installing.
A. Secure gem bar (1) on the
junction box (not
with two screws (2)
(supplied).
B. Make all wire connections
to appropriate wire.
Secure with wire nuts
(supplied
C. Connect the green wires
from the fixture and power
source to the green screw on the gem bar (
D.
The black wire from the fixture is
black wire from power source.
E.
The white wire from the fixture is connected to the
white (neutral) wire from power source.
F.
Tuck all connections neatly into junction box.
3. Mounting
A. Thread nut (6) on stem (3)
.
stem in the gem bar so
that approx.
Secure the necessary length with nut (4).
B. Install back panel (5)
over stem
the thumbnut (7).
4. Shade-To install the shade
(
diffuser with two
holes on the top and the bottom of the
backpan.
Secure shade with two screws
5
. Restore power at fuse or circuit breaker box.
Wall Fixture
& TPWW70050LWH
American Fluorescent Corporation warrants this fixture is
free from defects in materials and workmanship when installed and used under normal operating conditions
for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de
not cover failure due to improper installation, misuse, mishandling or damage incurred in transit
Safety Precautions
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with
these
instructions could result in potentially fatal electric shock and/or
It is recommended that a qualified
electrician perform all wiring. This
fixture must be wired in accordance with all national and local
handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a wet or damp surface or in water.
ASSEMBLY INSTRUCTIONS
Preparing for installation
Disconnect electrical power
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
misplace any of the screws or parts
which are needed for installing the fixture.
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit
breaker box. Check power wires for damage or scrapes.
If power supply wires are within three inc
hes of the
, use wire suitable for at least
90C
Most dwellings built before 1985 have
supply wire rated to 60C. Consult a qualified electrician
junction box (not
supplied)
(supplied).
to appropriate wire.
(supplied
).
from the fixture and power
source to the green screw on the gem bar (
1).
The black wire from the fixture is
connected to the
The white wire from the fixture is connected to the
white (neutral) wire from power source.
Tuck all connections neatly into junction box.
.
Adjust the length of the
that approx.
3/8” is exposed.
Secure the necessary length with nut (4).
over stem
(3) and secure it with
(
8) align two holes on the
holes on the top and the bottom of the
Secure shade with two screws
(9).
. Restore power at fuse or circuit breaker box.
LED Wall Sconce
120VAC / 60Hz
free from defects in materials and workmanship when installed and used under normal operating conditions
for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of de
fective fixture or compone
not cover failure due to improper installation, misuse, mishandling or damage incurred in transit
This fixture is designed for use in a 110
-
Do not use on a dimming circuit.
To reduce the
risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green)
between
this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
damp locations only.
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
which are needed for installing the fixture.
LED Wall Sconce
8060655 R1
free from defects in materials and workmanship when installed and used under normal operating conditions
fective fixture or compone
nts; it does
-
120VAC, 60Hz fused circuit.
risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green)
contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general
outdoor lighting in dry or
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts are included, as shown in figure below. Be careful not
to