Aspire 5735/5735Z/5335 Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on Aspire 5735/5735Z/5335 Series service guide.
Copyright Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
Table of Contents System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Removing the Middle Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Removing the Heatsink Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Removing the CPU Heatsink Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Online Support Information 159 Index 161 IX
Table of Contents X
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many feature: Platform Intel® Centrino® 2 processor technology, featuring: • Intel® Core™2 Duo processor* • Intel® Pentium® dual-core processor* • Intel® Celeron® processor* • Mobile Intel® GL40/GM45 Express Chipset (GL40 for Aspire 5730/5730Z/5330; GL45 for Aspire 5735/ 5735Z/5335) • Intel® Wireless WiFi Link 5100/5300* • Acer InviLink™ Nplify™ 802.11b/g/Draft-N* • Acer InviLink™ 802.
• High-definition audio support • MS-Sound compatible • Built-in microphone Communication • Integrated Acer Crystal Eye webcam* • WLAN: •Acer InviLink™ Nplify™ 802.11b/g/Draft-N* •Acer InviLink™ 802.11b/g* • WPAN: Bluetooth® 2.0+Enhanced Data Rate (EDR)* • LAN: Gigabit Ethernet; Wake-on-LAN ready • Modem: 56K ITU V.92; Wake-on-Ring ready I/O Ports • ExpressCard™/54 slot • 5-in-1 card reader (SD/MMC/MS/MS PRO/xD) • Three USB 2.
System Block Diagram Cathedral Peak II Block Diagram CLK GEN. Mobile CPU ICS 9LPRS365BKLFT (71.09365.A03) RTM 875N-606-LFT (71.00875.C03) 3 THERMAL EMC2102 Penryn 479 21 4, 5 HOST BUS DDR2 DIMM1 667/800 MHz 667/800MHz 14 AGTL+ CPU I/F DDR Memory I/F DDR2 DIMM2 INTEGRATED GRAHPICS 667/800MHz LVDS, CRT I/F 13 6,7,8,9,10,11 X4 DMI 400MHz INT.MIC 16 C-Link0 ICH9M Codec AZALIA ALC268 6 PCIe ports PCIex1 PCI/PCI BRIDGE 28 4 SATA PCIex1 12 USB 2.0/1.
Your Acer Notebook tour After knowing your computer features, let us show you around your new computer. Front View Icon 4 Item Description 1 Acer Crystal Eye webcam Web camera for video communication (only for certain models). 2 Display screen Also called Liquid-Crystal Display (LCD), displays computer output. 3 Power button Turns the computer on and off. 4 Empowering key Launch Acer Empowering Technology 5 Keyboard For entering data into your computer.
Icon Item Description 8 Click buttons (left and right) The left and right buttons function like the left and right mouse buttons. 9 Palmrest Comfortable support area for your hands when you use the computer. 10 Speakers Left and right speakers deliver stereo audio output. 11 Microphone Internal microphone for sound recording. 12 Easy-launch buttons Buttons for launching frequently used programs. Volume up/Volume down Increases the sound volume/Decreases the sound volume.
Left View # Icon Item Description 1 External display (VGA) port Connects to a display device (e.g., external monitor, LCD projector). 2 Ethernet (RJ-45) port Connects to an Ethernet 10/100/1000-based network. 3 USB 2.0 ports Connect to USB 2.0 devices (e.g., USB mouse, USB camera) (only for certain models). 4 Microphone-in jack Accepts input from external microphones. 5 Headphones/ speaker/line-out jack with S/PDIF support Connects to audio line-out devices (e.g., speakers, headphones).
Icon Item Description 4 Emergency eject hole Ejects the optical drive tray when the computer is turned off. Note: Insert a paper clip to the emergency eject hole to eject the optical drive tray when the computer is off. 5 Modem (RJ-11) port Connects to a phone line. 6 DC-in jack Connects to an AC adapter. 7 Kensington lock slot Connects to a Kensington-compatible computer security lock.
Bottom View Icon 8 Item Description 1 Battery bay Houses the computer's battery pack. 2 Battery release latch Releases the battery for removal. 3 Battery lock Locks the battery in position. 4 Memory compartment Houses the computer's main memory. 5 Hard disk bay Houses the computer's hard disk (secured with screws). 6 Ventilation slots and cooling fan Enable the computer to stay cool, even after prolonged use. Note: Do not cover or obstruct the opening of the fan.
Indicators The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed. Icon Function Description HDD Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated. Caps Lock Lights up when Caps Lock is activated. Power Indicates the computer's power status. Battery Indicates the computer's battery status. NOTE: 1. Charging: The light shows amber when the battery is charging. 2.
Touchpad basics (with two-click buttons) The following items show you how to use the touchpad with two-click buttons. 1 2 3 • Move your finger across the touchpad (1) to move the cursor. • Press the left (2) and right (3) buttons located beneath the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad is the same as clicking the left button.
Using the Keyboard The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock + When Num Lock is on, the embedded keypad is in numeric mode.
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Keys The computer employs hotkeys or key combinations to access most of the computer’s controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the key before pressing the other key in the hotkey combination. Hotkey Icon Function Description + Hotkey help Displays help on hotkeys. + Acer eSettings Launches Acer eSettings in Acer Empowering Technology.
Special Key (only for certain models) You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol 1. Open a text editor or word processor. 2. Either press < > at the bottom-right of the keyboard, or hold and then press the <5> key at the upper-center of the keyboard. NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information.
Acer Empowering Technology The Empowering Technology toolbar makes it easy for you to access frequently used functions and manage your new Acer system. Activated by pressing the Empowering Key, it provides access to the following utilities: NOTE: The following content is for general reference only. Actual product specifications may vary. • Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home Theater on your system (only for certain models).
Empowering Technology password You must set the Empowering Technology password to use the password protection feature of Acer eRecovery Management to protect your data. To set the Empowering Technology password: 16 1. Launch Acer eRecovery Management. 2. Click the Restore tab. 3. Click Password settings. The Empowering Technology Password Center dialogue box pops up. 4. Click Create a new password. 5.
Acer eAudio Management (only for certain models) Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home Theater on your system. Select Movie or Game mode to experience the awesome realism of 5.1-channel audio output from the speakers fitted to your system via Dolby Surround sound technology. Music mode lets you enjoy your favorite tunes, in vivid detail. To choose your playback device, click the window.
Acer ePower Management Acer ePower Management features a straightforward user interface for configuring your power management options. To access this utility, select Acer ePower Management from the Empowering Technology toolbar, run the program from the Acer Empowering Technology program group in Start menu, or right-click the Windows power icon in the system tray and select Acer ePower Management.
Battery status 1. The quick menu shows the remaining battery life based on current usage. 2. You can also launch the Acer ePower Management application and refer to the Battery status panel located just below the power plans. 3. Click the Battery tab to view remaining battery life, battery status, and remaining battery life in standby and hibernate modes.
If you set a different password to encrypt a file, but you forgot the encryption password, you can use the Master Password to decrypt the file. NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the Master Password is the only other key capable of decrypting the file.
•Back up factory default to CD/DVD •Back up drivers and applications to CD/DVD •Create user backup •Manage • user backups Restore: •Restore system to factory default •Reinstall •Restore applications/drivers system from user backup •Password settings To use the password protection feature of Acer eRecovery Management to protect your data, you must first set the Empowering Technology password. To set the password, refer to the section "Empowering Technology password".
Acer eSettings Management Acer eSettings Management allows you to inspect hardware specifications, set BIOS passwords and modify boot options. Acer eSettings Management also: 22 • Provides a simple graphical user interface for navigation. • Prints and saves hardware specifications. • Lets you set an asset tag for your system.
Windows Mobility Center The Windows Mobility Center collects key mobile-related system settings in one easy-to-find place, so you can quickly configure your Acer system to fit the situation as you change locations, networks or activities. Settings include display brightness, volume, power plan, wireless networking on/off, external display settings, synchronization status and presentation settings.
Using the System Utilities Acer GridVista (dual-display compatible) NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value.
Hardware Specifications and Configurations Processor Item Specification CPU type ® Core™2 Duo T5800 (2.0G)/T5900/T9400 (2.53G)/P7350 Intel (2.0G)/P8400 (2.26G) for Aspire 5735 Intel® Pentium® dual-core T3200 (2.0G)/T3400 for Aspire 5735Z Intel® Celeron® M 575 (2.0G)/585 (2.16G)/T1600 (1.66G) for Aspire 5335 Intel® Core™2 Duo Mobile Processor P8400 (2.26G), P8600 (2.4 G), P9500 (2.53G), T9400 (2.53G), T9600 (2.
Memory Combinations Slot 1 Slot 2 Total Memory 0MB 512MB 512MB 0MB 1024MB 1024MB 0MB 2048MB 2048MB 512MB 512MB 1024MB 512MB 1024MB 1536MB 512MB 2048MB 2560MB 1024MB 0MB 1024MB 1024MB 512MB 1536MB 1024MB 1024MB 2048MB 1024MB 2048MB 3072MB 2048MB 0MB 2048MB 2048MB 512MB 2560MB 2048MB 1024MB 3072MB 2048MB 2048MB 4096MB NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations.
Wireless Module 802.11b/g Item Specification Protocol 802.
Optical Disc Drive Item Specification Transfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Buffer Memory 2MB Sustained: Max 10.08Mbytes/sec Interface SATA Applicable disc format Applicable disc format CD: CD-DA, CD-ROM, CD-ROM XA, Photo CD (multi-session), Video CD, Cd-Extra (CD+), CD-text DVD: DVD-VIDEO, DVD-ROM, DVD-R (3.9GB, 4.
Audio Interface Item Internal speaker / Quantity Specification Yes/2 (1.5W speakers) Video Memory Item Specification Chipset GL45 (built-in Cantiga) Memory size depends on setup setting Item Specification Chipset ICH9M USB Compliancy Level 2.0 OHCI USB 1.1 and USB 2.
Battery Item Specification Battery Type Li-ion Pack capacity 6Cell 4400 MAH/8Cell 4800 MAH Number of battery cell 6/8 Package configuration 3 cells in series, 2 series in parallel 4 cells in series, 2 series in parallel LCD 15.4” inch Item Specification Vendor & model name CMO/AUO/LG Screen Diagonal (mm) 15.4 inches Display resolution (pixels) 1280 x 800 WXGA Pixel Pitch 0.204 x 0.204 Pixel Arrangement R.G.B.
System Power Management ACPI mode 32 Power Management Suspend to RAM (S3) CPU set power down VGA Suspend PCMCIA Suspend Audio Power Down Hard Disk Power Down CD-ROM Power Down Super I/O Low Power mode Save to Disk (S4) Also called Hibernation Mode. System saves all system states and data onto the disc prior to power off the whole system.
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Navigating the BIOS Utility There are five menu options: Information, Main, Security, Boot, and Exit. Follow these instructions: q To choose a menu, use the left and right arrow keys. q To choose an item, use the up and down arrow keys. q To change the value of a parameter, press F5 or F6. q A plus sign (+) indicates the item has sub-items. Press Enter to expand this item. q Press Esc while you are in any of the menu options to go to the Exit menu.
Information The Information screen displays a summary of your computer hardware information. Information Main Phoenix SecureCore(tm) Setup Utility Security Boot Exit C P U Ty p e : CPU Speed: IDE0 Model Name: IDE0 Serial Number: ATA P I M o d e l N a m e : S y s t e m B I O S Ve r s i o n : V G A B I O S Ve r s i o n : K B C Ve r s i o n : Serial Number: A s s e t Ta g N u m b e r : Product Name: Manufacturer Name: UUID: F1 Help Esc Exit Select Item Select Menu Intel (R) Core (TM)2 Duo CPU T9400 @ 2.
Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Format/Option System Time Sets the system time. The hours are displayed with 24-hour format. Format: HH:MM:SS (hour:minute:second) System Time System Date Sets the system date. Format MM/DD/YYYY (month/day/ year) System Memory This field reports the memory size of the system.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Option Supervisor Password Is Shows the setting of the Supervisor password Clear or Set User Password Is Shows the setting of the user password. Clear or Set HDD Password Is Shows the setting of the hard disk password. Clear or Set Set Supervisor Password Press Enter to set the supervisor password.
Removing a Password Follow these steps: 1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears: 2. Type the current password in the Enter Current Password field and press e. 3. Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to “Clear”. 4.
If the current password entered does not match the actual current password, the screen will show you the Setup Warning. If the new password and confirm new password strings do not match, the screen will display the following message.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Exit The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the BIOS Setup Utility. Phoenix SecureCore(tm) Setup Utility Security Exit Main Boot Information Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help Esc Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: q New versions of system programs q New features or options q Restore a BIOS when it becomes corrupted. Use the Flash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Flash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
Remove HDD/BIOS Utility This section provide you with removing HDD/BIOS method: Remove HDD Password: q If you key in wrong HDD password for three time, “HDD password error code” would display on the screen. See the image below. q If you need to solve HDD password locked problem, you can run HDD_PW.EXE 1. Key in “hdd_pw 15494 0” 2. Select “2” 3. Choose one upper-case string q Chapter 2 Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password.
46 Chapter 2
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.
General Information Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, stable surface. 4. Remove the battery pack.
External Module Disassembly Process External Modules Disassembly Flowchart The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Removing the Battery Pack 50 1. Turn base unit over. 2. Slide the battery lock/unlock latch to the unlock position. 3. Slide the battery release latch to the release position to pop out the battery pack, then remove the battery pack from the main unit.
Removing the SD dummy card 1. Push the SD dummy card all the way in to eject it. 2. Pull it out from the slot. Removing the ExpressCard dummy card 1. Push the ExpressCard dummy card all the way in to eject it.
2. Pull it out from the slot. Removing the Lower Cover 1. See “Removing the Battery Pack” on page 50. 2. Remove the four captive screws and the six screws (A) on the lower cover. Step 1~6 52 Size (Quantity) M2.5 x L8 (6) Color Black Torque 3.
3. Use a plastic screw driver to carefully pry open the lower cover. 4. Remove the lower cover from the lower case. Removing the DIMM 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52.. 3. Push out the latches on both sides of the DIMM socket to release the DIMM.
4. Remove the DIMM module. Removing the WLAN Board Modules 54 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52. 3. Remove the white antenna cable that is taped to the WLAN board module.
4. Disconnect the antenna cables from the WLAN board. NOTE: There are 2 antenna cables connected to the WLAN board module. The Black antenna cable is connected to the MAIN connector and the Gray antenna cable is connected to the AUX connector. 5. Move the antenna away from the WLAN board and remove the one screw (H) on the WLAN board to release the WLAN board. Step 1 Chapter 3 Size (Quantity) M2 x L3 (1) Color Black Torque 1.
6. Detach the WLAN board from the WLAN socket. NOTE: When attaching the antenna back to the WLAN board, make sure the cable are arranged properly. Removing the Hard Disk Drive Module 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52. 3. Remove the one screw (C) securing the hard disk drive module. Step 1 56 Size (Quantity) M2 x L3 (1) Color Silver Torque 1.
4. Slide the hard disk drive module away from the connector. 5. Lift the hard disk drive module and remove it from the hard disk drive bay. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 6. Remove the two adhesive tape covering the two screws.
7. Remove the two screws (D) securing the hard disk to the bracket and remove the hard disk from the bracket. Step 1~2 Size (Quantity) M3 x L4 (2) Color Silver Torque 3.0 kgf-cm Removing the Optical Drive Module 58 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52.
3. Use a pin and push it inside the emergency eject hole to eject the odd drive tray. 4. Carefully pull out the odd drive tray until the part of the module is visible and then slowly push back to close the tray into the module with the module still partially exposed. 5. Slowly pull out the odd module from the odd drive bay.
6. Remove the two screws (C) securing the locker bracket and remove the locker bracket from the optical disk drive module. Step 1~2 60 Size (Quantity) M2 x L3 (2) Color Silver Torque 1.
Main Unit Disassembly Process Main Unit Disassembly Flowchart MAIN UNIT DISASSEMBLY MAIN UNIT Cx1 MIDDLE COVER HEAT SINK FAN SCREW X 4 KEYBOARD CPU THERMAL MODULE Ax2, Ex2 LCD MODULE CPU A x 11, G x 4 UPPER CASE Cx1 MODEM CARD SPEAKER MODULE LED BOARD Cx1 Cx1 MAIN BOARD Cx4 Cx1 BLUETOOTH MODULE USB MODULE Cx2 TOUCHPAD BRACKET TOUCHPAD MODULE Screw List Item Screw Color Part No. A M2 x L8 Black 86.00E34.738 C M2 x L3 Silver 86.9A522.3R0 E M2.5 x L10 Silver 86.00F84.
Removing the Middle Cover 62 1. See “Removing the Battery Pack” on page 50. 2. Use a plastic screw driver to pry loose the side of the middle cover. 3. Carefully pry loose the middle cover from the latches securing it and remove the middle cover.
Removing the Keyboard 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Middle Cover” on page 62. 3. Push down on the lock and release the latches securing the keyboard to the upper case. 4. Carefully pry loose the keyboard and turn it over on the touchpad area.
5. Disconnect the keyboard cable from the main board to remove the keyboard. Removing the Heatsink Fan Module 64 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52. 3. Disconnect the heatsink fan connector from the main board.
4. Remove the one screw (C) securing the heatsink fan module in place. Step 1 5. Size (Quantity) M2 x L3 (1) Color Silver Torque 1.6 kgf-cm Carefully lift up the heatsink fan module. Removing the CPU Heatsink Module 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52. 3. See “Removing the Heatsink Fan Module” on page 64.
4. Remove the four screws securing the CPU heatsink module. 5. Carefully remove the heatsink module from the system. Removing the CPU 66 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the Lower Cover” on page 52. 3. See “Removing the Heatsink Fan Module” on page 64. 4. See “Removing the CPU Heatsink Module” on page 65. 5. Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU.
6. Lift up carefully to remove the CPU. NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown. Removing the LCD Module 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62. 7.
9. Turn over the system and remove the two screws (A) from the bottom of the left and right hinges. Step 1~2 Size (Quantity) M2.5 x L8 (2) Color Black Torque 3.0 kgf-cm 10. Disconnect the LCD cable connector from the main board.
11. Carefully pull out the wireless antenna cables from the hole and release the cables from the latches. 12. Remove the two screws (E) from the left and right hinge of the LCD module. Step 1~2 Chapter 3 Size (Quantity) M2.5 x L10 (2) Color Silver Torque 3.
13. Carefully remove the LCD module from the base unit. NOTE: When connecting the cable back to the unit, please note that the cable should be routed well. Separating the Upper Case from the Lower Case 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7.
15. Disconnect the touchpad cable from the TPAD1 connector on the main board. 16. Disconnect the LED cable from LEDCN1 on the main board.
17. Disconnect the speaker cable from the INTSPK1 connector on the main board. 18. Remove the eleven screws (11 x A, 1 x G) from the bottom panel. Step 72 Size (Quantity) Color Torque 1~11 M2.5 x L8 (11) Black 3.0 kgf-cm 12 M2 x L4 (1) Black 3.
19. Turn the unit over and remove the three screws (G) from the top panel. Step 1~3 Size (Quantity) M2 x L4 (3) Color Black Torque 3.0 kgf-cm 20. Gently remove the upper case from the lower case. Removing the LED Board 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6.
11. See “Removing the Heatsink Fan Module” on page 64. 12. See “Removing the CPU Heatsink Module” on page 65. 13. See “Removing the CPU” on page 66. 14. See “Removing the LCD Module” on page 67. 15. See “Separating the Upper Case from the Lower Case” on page 70. 16. Disconnect the LED cable from the LED board. 17. Disconnect the internal microphone cable from the INTMIC1 connector on the LED board.
18. Remove the one screw (C) securing the LED board. Step 1 Size (Quantity) M2 x L3 (1) Color Silver Torque 1.6 kgf-cm 19. Remove the LED board from the upper cover. Removing the Speaker Module 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7.
11. See “Removing the Heatsink Fan Module” on page 64. 12. See “Removing the CPU Heatsink Module” on page 65. 13. See “Removing the CPU” on page 66. 14. See “Removing the LCD Module” on page 67. 15. See “Separating the Upper Case from the Lower Case” on page 70. 16. Remove the four screws (C) securing the speaker module. Step 1~4 Size (Quantity) M2 x L3 (4) Color Silver Torque 1.6 kgf-cm 17. Remove the tape covering the speaker cable.
18. Release the speaker cable from the latches. 19. Remove the speaker module from the upper case. Removing the Touchpad Module 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7. See “Removing the Hard Disk Drive Module” on page 56. 8.
13. See “Removing the CPU” on page 66. 14. See “Removing the LCD Module” on page 67. 15. See “Separating the Upper Case from the Lower Case” on page 70. 16. Remove the touchpad cable that is glued to the bracket. 17. Disconnect the touchpad cable from the touchpad board.
18. Remove the two screws (C) securing the bracket to the upper case. Step 1~2 Size (Quantity) M2 x L2 (2) Color Silver Torque 1.6 kgf-cm 19. Remove the touchpad bracket.
20. Carefully pry loose and remove the touch pad board. WARNING:The touchpad board is glued to the upper case, only remove the touchpad board if it is defective. Removing the Modem Board 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7.
13. See “Removing the CPU” on page 66. 14. See “Removing the LCD Module” on page 67. 15. See “Separating the Upper Case from the Lower Case” on page 70. 16. Remove the one screw (C) securing the modem card. Step 1 Size (Quantity) M2 x L3 (1) Color Silver Torque 1.6 kgf-cm 17. Lift the modem board from the main board.
18. Disconnect the cable from the modem board. Removing the Main Board 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7. See “Removing the Hard Disk Drive Module” on page 56. 8. See “Removing the Optical Drive Module” on page 58. 9.
17. Disconnect the USB cable from the USBCN1 connector on the main board. 18. Disconnect the bluetooth cable from the BLUE1 connector on the main board. 19. Remove the one screw (C) securing the main board in place. Step 1 Chapter 3 Size (Quantity) M2 x L3 (1) Color Silver Torque 1.
20. Carefully remove the main board. Removing the USB Board Module 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7. See “Removing the Hard Disk Drive Module” on page 56. 8. See “Removing the Optical Drive Module” on page 58. 9.
17. Remove the one screw (C) securing the USB board module to the lower case. Step 1 Size (Quantity) M2 x L3 (1) Color Silver Torque 1.6 kgf-cm 18. Release the USB cable from the latch. 19. Remove the USB board module from the lower case.
Removing the Bluetooth Modules 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the DIMM” on page 53. 6. See “Removing the WLAN Board Modules” on page 54. 7. See “Removing the Hard Disk Drive Module” on page 56. 8. See “Removing the Optical Drive Module” on page 58. 9. See “Removing the Middle Cover” on page 62. 10.
LCD Module Disassembly Process LCD Module Disassembly Flowchart LCD MODULE DISASSEMBLY LCD MODULE Bx4 LCD BEZEL Bx5 LCD ASSEMBLY Fx2 LCD FPC CABLE LEFT LCD BRACKET Fx2 LCD BACK PANEL RIGHT LCD BRACKET ANTENNAS VGA CAMERA Screw List Item Screw Color Part No. B M2.5 x L6 Black 86.00E12.536 F M2 x L4 Silver 86.00C07.
Removing the LCD Bezel 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62. 7. See “Removing the Heatsink Fan Module” on page 64. 8. See “Removing the CPU Heatsink Module” on page 65. 9. See “Removing the LCD Module” on page 67. 10.
12. Carefully pry open the LCD bezel and place the bezel on top of the LCD panel. Removing the LCD panel with the Brackets 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62. 7. See “Removing the Heatsink Fan Module” on page 64. 8.
11. Disconnect the cable from the web camera. 12. Remove the five screws (5 x B) securing the LCD module. Step 1~5 Size (Quantity) M2.5 x L6 (5) Color Black Torque 3.0 kgf-cm 13. Remove the LCD with the brackets from the back cover. Removing the Inverter Board and FPC Cable 1. 90 See “Removing the Battery Pack” on page 50.
2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62. 7. See “Removing the Heatsink Fan Module” on page 64. 8. See “Removing the CPU Heatsink Module” on page 65. 9. See “Removing the LCD Module” on page 67. 10. See “Removing the LCD Bezel” on page 88. 11.
13. Detach any adhesive tapes and any cable that is glued to the LCD panel.
14. Disconnect the FPC cable from the LCD panel. Removing the LCD Brackets 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62. 7. See “Removing the Heatsink Fan Module” on page 64. 8. See “Removing the CPU Heatsink Module” on page 65. 9.
Step 1~4 Size (Quantity) M2 x L4 (4) Color Silver Torque 1.0 kgf-cm Removing the Antennas 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62. 7. See “Removing the Heatsink Fan Module” on page 64. 8.
13. Remove the left and right antenna cables together with the tapes holding them in place. NOTE: There is no need to remove the antenna unless you really need to replace it. Removing the Web Camera 1. See “Removing the Battery Pack” on page 50. 2. See “Removing the SD dummy card” on page 51. 3. See “Removing the ExpressCard dummy card” on page 51. 4. See “Removing the Lower Cover” on page 52. 5. See “Removing the WLAN Board Modules” on page 54. 6. See “Removing the Middle Cover” on page 62.
12. Remove the Web camera from the back cover.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. Boot from the diagnostics diskette and start the diagnostics program. 2.
q External keyboard If any of these devices do not work, reconnect the cable connector and repeat the failing operation. Memory Check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the diagnostic program (please refer to main board. 2. Go to the diagnostic memory in the test items. 3. Press F2 in the test items. 4. Follow the instructions in the message window.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: q Replace the System board. q If the problem is not corrected, see “Undetermined Problems” on page 116. q If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes Error Messages 006 Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 System disabled. Incorrect password is specified.
Error Message List Error Messages 104 FRU/Action in Sequence System timer error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Real time clock error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages FRU/Action in Sequence No beep, power-on indicator turns off and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 99.. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 99..
Phoenix BIOS Beep Codes Code Beeps Verify Real Mode 03h Disable Non-Maskable Interrupt (NMI) 04h Get CPU type 06h Initialize system hardware 08h Initialize chipset with initial POST values 09h Set IN POST flag 0Ah Initialize CPU registers 0Bh Enable CPU cache 0Ch Initialize caches to initial POST values 0Eh Initialize I/O component 0Fh Initialize the local bus IDE 10h Initialize Power Management 11h Load alternate registers with initial POST values 12h Restore CPU control word du
Code Beeps POST Routine Description 3Ch Advanced configuration of chipset registers 3Dh Load alternate registers with CMOS values 42h Initialize interrupt vectors 45h POST device initialization 46h 2-1-2-3 Check ROM copyright notice 48h Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h In
Code POST Routine Description Detect and install external RS232 ports 83h Configure non-MCD IDE controllers 84h Detect and install external parallel ports 85h Initialize PC-compatible PnP ISA devices 86h Re-initialize onboard I/O ports 87h Configure Motherboard Configurable Devices (optional) 88h Initialize BIOS Area 89h Enable Non-Maskable Interrupts (NMIs) 8Ah Initialize Extended BIOS Data Area 8Bh Test and initialize PS/2 mouse 8Ch Initialize floppy controller 8Fh Determine number
Code Beeps POST Routine Description B9h Prepare Boot BAh Initialize DMI parameters BBh Initialize PnP Option ROMs BCh Clear parity checkers BDh Display MultiBoot menu BEh Clear screen (optional) BFh Check virus and backup reminders C0h Try to boot with INT 19 C1h Initialize POST Error Manager (PEM) C2h Initialize error logging C3h Initialize error display function C4h Initialize system error handler C5h PnPnd dual CMOS (optional) C6h Initialize notebook docking (optional) C7h
Code 110 Beeps F5h Boot to Mini DOS F6h Clear Huge Segment F7h Boot to Full DOS Chapter 4
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error Action in Sequence LCD backlight doesn't work LCD is too dark LCD brightness cannot be adjusted LCD contrast cannot be adjusted Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. Reconnect the LCD connectors. Keyboard (if contrast and brightness function key doesn't work).
Power-Related Symptoms Symptom / Error Action in Sequence The system doesn’t power-off. Power source (battery pack and power adapter). See “Power System Check” on page 99. Hold and press the power switch for more than 4 seconds. System board Battery can’t be charged See “Check the Battery Pack” on page 101. Battery pack System board PCMCIA-Related Symptoms Symptom / Error Action in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly System board PCMCIA slot pin is damaged.
Power Management-Related Symptoms Symptom / Error Action in Sequence The system doesn't resume from hibernation mode. See “Save to Disk (S4)” on page 32. Hard disk connection board Hard disk drive System board The system doesn't resume from standby mode after opening the LCD. See “Save to Disk (S4)” on page 32. LCD cover switch System board Battery fuel gauge in Windows doesn’t go higher than 90%. Remove battery pack and let it cool for 2 hours.
Keyboard/Touchpad-Related Symptoms Symptom / Error Touchpad does not work. Action in Sequence Reconnect touchpad cable. Touchpad board System board Modem-Related Symptoms Symptom / Error Internal modem does not work correctly. Action in Sequence Modem phone port modem combo board System board NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined Problems” on page 116.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 99.
Chapter 5 Jumper and Connector Locations Top and Bottom View Chapter 5 117
118 Chapter 5
Clearing Password Check and BIOS Recovery This section provide you the standard operating procedures of clearing password and BIOS recovery for Aspire 5730Z/5330 Series. Aspire 5730Z/5330 Series provide one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.
BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. BIOS Recovery Hotkey: The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered on during BIOS POST.
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of 5730Z/5330 Series. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Aspire 5735/5735Z/5335 Series Exploded Diagram 122 Chapter 6
Aspire 5735/5735Z/5335 Series FRU List Aspire 5735 Series FRU List CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO ADAPTER ADAPTER 65W DELTA SADP-65KB DFA LF LEVEL-4 ADT 65W SADP-65KB DFA LF DELTA AP.06501.013 ADAPTER 65W 3PIN DELTA SADP65KB BFJA LF LEVEL-4 FOR OBL ONLY ADP 65W 3P SADP-65KB BFJA DELT AP.06501.014 ADAPTER 65W LITEON PA-165002AC LF LEVEL-4 ADT 65W PA-1650-02AC LF AP.06503.016 ADAPTER 65W HIPRO HPOK065B13 LF LEVEL-4 ADP 65W 3P HPOK065B13LF AP.0650A.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO TOUCHPAD BOARD SYNAPTICS TM00540-005 TOUCHPAD SYNAPTICS TM00540-005 56.ATR01.001 WIRELESS LAN BOARD 512AN_MMWG SHIRLEY PEAK 5100 MM#895361 WLAN 802.11ABGN SHIRLEYPEAK1*2 KI.SPM01.003 WIRELESS LAN BOARD 512AG_MMWG SHIRLEY PEAK 5100 MM#897004 WLAN 802.11ABG SHIRLEYPEAK1*2 KI.SPM01.005 WIRELESS LAN BOARD 533AN_MMWG SHIRLEY PEAK MM#895362 WLAN 802.11ABGN SHIRLEYPEAK3*3 KI.SPM01.001 POWER CORD 3A 250V 3PIN UK CODE UK 2.5A 250V 3P BK 27.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO POWER CORD 10A 250V 3PIN CHINA CORD CHINA 10A 250V 3P 27.01518.591 POWER CORD 10A 250V 3PIN CHINA BK CORD 10A 250V 3P CHINA BK 27.01518.701 POWER CORD 10A 250V 3PIN ITALY CORD ITALY 10A 250V 3P BK 27.01518.611 POWER CORD 10A CORD 10A 250V 3P 250V 3PIN ITALY BK ITALY BK 27.01518.711 POWER CORD 2.5A 250V AUSTRALIA CORD 2.5A 250V AUSTRALIA BK 27.01518.621 POWER CORD 7A 125V 2PIN JAPAN BK CODE 7A 125V 2P JAPAN BK 27.01518.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO LOWER CASE W/ DC-IN CABLE&MODEM CABLE&SPEAKER RIGHT 60 LCASE ASSY CP2 60.ATR01.001 DC-IN CABLE C.A. DC IN CABLE CP2 MEC RESERVE DC-IN CABLE C.A.DC IN CABLE CP2 HL RESERVE DC-IN CABLE C.A.DC IN CABLE CP2 HT RESERVE MODEM CABLE C.A. RJ11 CABLE CP2 MEC RESERVE MODEM CABLE RJ11 CABLE CP2 HL RESERVE MODEM CABLE C.A. RJ11 CABLE CP2 HT RESERVE SPEAKER RIGHT SPEAKER R CP2 23.ATR01.001 SPEAKER RIGHT SPEAKER RIGHT CP2 YG 23.ATR01.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO CPU/PROCESSOR CPU INTEL CORE2DUAL P7350 PGA 2.0G 3M 1066 25W IC CPU PENRYN P7350 2.0G PGA KC.73501.DPP CPU/PROCESSOR CPU INTEL CORE2DUAL P8400 PGA 2.26G 3M 1066 25W IC CPU PENRYN P8400 2.26G PGA KC.84001.DPP CPU/PROCESSOR CPU INTEL CORE2DUAL P8600 PGA 2.4G 1066 25W 3M IC CPU PENRYN P8600 2.4G PGA KC.86001.DPP CPU/PROCESSOR CPU INTEL CORE2DUAL P9500 PGA 2.53G 6M 1066 25W IC CPU PENRYN P9500 2.53G PGA KC.95001.
CATEGORY 128 No. PART NAME DESCRIPTION ACER OEM PURCHASE NO CASE/COVER/BRACKET ASSEMBLY HDD BRACKET 60 HDD BRK ASSY CP2 33.ATR01.003 HDD/HARD DISK DRIVE HDD 120GB 5400RPM SATA SEAGATE ST9120817AS LF F/ W:3.AAA HDD 120GB SGT SATA ST9120817AS KH.12001.032 HDD/HARD DISK DRIVE HDD 120GB 5400RPM SATA HGST HT543212L9A300 FW:C40C HDD 120GB HT543212L9A300 C40C KH.12007.016 HDD/HARD DISK DRIVE HDD 120GB 5400RPM SATA WD WD1200BEVS22UST0 ML125 LF F/W:01.01A01 HDD 120GB WD WD1200BEVS-22UST0 KH.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO HDD/HARD DISK DRIVE HDD 250GB 5400RPM SATA SEAGATE ST9250827AS F/ W:2.ALA HDD 250GB SGT SATA ST9250827AS KH.25001.011 HDD/HARD DISK DRIVE HDD 250GB 5400RPM SATA TOSHIBA MK2552GSX F/ W:LV010J HDD 250GB TOSHIBA MK2552GSX KH.25004.002 HDD/HARD DISK DRIVE HDD MODULE 320G 5400RPM SATA HDD 320GB5.4KS FOR CP2 TBD CASE/COVER/BRACKET ASSEMBLY HDD BRACKET 60 HDD BRK ASSY CP2 33.ATR01.
CATEGORY 130 No. PART NAME DESCRIPTION ACER OEM PURCHASE NO KEYBOARD KEYBOARD 17KBFV5 BLACK 105KS US INTERNATIONAL HEBREW KB DARFON NSK-AFF0H HE HEBREW KB.I1700.005 KEYBOARD KEYBOARD 17KBFV5 BLACK 106KS TURKISH KB DARFON NSK-AFF0T TR TURKISH KB.I1700.007 KEYBOARD KEYBOARD 17KBFV5 BLACK 105KS THAILAND KB DARFON NSK-AFF03 TH THAI KB.I1700.008 KEYBOARD KEYBOARD 17KBFV5 BLACK 106KS SWISS/G KB DARFON NSK-AFF00 SW SWISS KB.I1700.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO KEYBOARD KEYBOARD 17KBFV5 BLACK 106KS CANADIAN FRENCH KB DARFON NSK-AFF0M FC FR-CANA KB.I1700.033 KEYBOARD KEYBOARD 17KBFV5 BLACK 106KS BRAZILIAN PORTUGUESE KB DARFON NSK-AFF1B BP BRAZ-PT KB.I1700.034 KEYBOARD KEYBOARD 17KBFV5 BLACK 106KS BELGIUM KB DARFON NSK-AFF1A BE BELGIAN KB.I1700.035 KEYBOARD KEYBOARD 17KBFV5 BLACK 105KS ARABIC/ENGLISH KB DARFON NSK-AFF0A AR ARABIC KB.I1700.
CATEGORY 132 No. PART NAME DESCRIPTION ACER OEM PURCHASE NO CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE RIGHT HINGE LCD R CP2 SZS 33.ATR01.004 CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE LEFT HINGE LCD L CP2 LH 33.ATR01.005 CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE LEFT HINGE LCD L CP2 SZS 33.ATR01.005 CASE/COVER/BRACKET ASSEMBLY LCD COVER 15.6" W/ANTENNA*2 ASSY LCD PANEL 1X2 CP2 60.ATR01.005 CASE/COVER/BRACKET ASSEMBLY LCD BEZEL 15.
CATEGORY No. PART NAME DESCRIPTION ACER OEM PURCHASE NO CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE RIGHT HINGE LCD R CP2 LH 33.ATR01.004 CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE RIGHT HINGE LCD R CP2 SZS 33.ATR01.004 CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE LEFT HINGE LCD L CP2 LH 33.ATR01.005 CASE/COVER/BRACKET ASSEMBLY LCD BRACKET W/ HINGE LEFT HINGE LCD L CP2 SZS 33.ATR01.005 CASE/COVER/BRACKET ASSEMBLY LCD COVER 15.6" W/ANTENNA*3 ASSY LCD PANEL CP2 60.ATR01.
CATEGORY 134 No. PART NAME DESCRIPTION ACER OEM PURCHASE NO MEMORY SODIMM 1GB DDRII667 A-DATA HYOPE1A0834Z LF SODIMM 1G HYOPE1A0834Z KN.1GB0C.005 MEMORY SODIMM 2GB DDRII667 SAMSUNG M470T5663QZ3CE6 LF SODIMM 2G M470T5663QZ3-CE6 KN.2GB0B.003 MEMORY SODIMM 2GB DDRII667 NANYA NT2GT64U8HD0BN -3C LF (0.07U) SODIMM 2G NT2GT64U8HD0BN-3C KN.2GB03.011 MEMORY SODIMM 2GB DDRII667 HYNIX HYMP125S64CP8Y5 LF SODIMM 2G HYMP125S64CP8-Y5 KN.2GB0G.
Chapter 6 135
Appendix A Model Definition and Configuration Aspire 5735/5735Z/5335 Series Please double click the red paper clip below for model definition and configurations details.
Appendix B Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows® XP Home, Windows® XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Microsoft® Windows® Vista Environment Test Item Specification CRT Port Test CRT Monitor Acer 211c 21”, ViewSonic G220F, ViewSonic PF790 19” LCD Monitor Acer FP751 17” TFT LCD, Acer AL1521, Acer AL1721, ViewSonic VD201b, Westinghouse W37G, HP LP2065, HP S9500 Projector Dell 3300MP USB Port Test USB Keyboard/Mouse Microsoft Natural Keyboard Pro Dell USB Keyboard Logicool USB Mouse (OWCM-USB) Logitech USB Wheel Mouse Logitech First Wheel Mouse Dell by Logitech Dell Internet Navigator Keyboard Dell Sma
Item Specification PCMCIA Test LAN/Modem Card TDK CardBus Ethernet 10/100 32-Bit CBE-10/100BTX Storage Card Hitachi Microdrive 4G 1394 Card Buffalo 1394 Interface Cardbus (IFC-ILCB/DV) USB2.0 Card IBM EtherJet CardBus Adapter 10/100 Wireless Lan Card Cisco Wireless LAN Card 802.11a (Not recommended for wireless ready model) NETGEAR Wireless LAN card 802.
140 Appendix B
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
142 Appendix C
Index A Features 1 AFLASH Utility Antennas Audio 44 fpc cable 90 Flash Utility 44 94 FRU (Field Replaceable Unit) List 30 H B Battery Pack BIOS Hard disk 50 HDD 56 28 Hibernation mode 13 Hot Keys 11 hotkey 33–44 Navigating 34 BIOS Utility Onboard Device Configuration 39 Security 37, 38 System Security 43 I Indicators 9 Board Layout Intermittent Problems 115 Top View 117 J brightness hotkeys 28 Hard Disk Drive Module 26 vendor 26 Version 26 13 Jumper and Connector Locations C
V 130 Modem Board 80 Model Definition view N left 6 rear 7 right 6 Notebook Manager 13 hotkey W num lock on indicator 9 Windows 2000 Environment Test WLAN Board O Online Support Information 159 P Panel 4 Bottom left 4 PC Card 8 9 Power System Check 99 Battery Pack 101 Power Adapter 100 Processor 26 S Screw List 48 speakers hotkey 13 System Block Diagram 3 System Check Procedures 98 26 System Utilities 33 System Memory T Test Compatible Components Top 117 touchpad hotkey 13 10
