Aspire 7730/7730G Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on Aspire 7730/7730G Series service guide.
Copyright Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
Table of Contents System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 Removing the Switch Board . . . . . . . . . . . . . . . . . .
Table of Contents Replacing the MXM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Replacing the ExpressCard Dummy Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Replacing the SD Dummy Tray . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Display Port Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 USB Port Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 Access Point Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195 Bluetooth Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195 Card Reader Test . . . . .
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many feature: Operating System • Windows® Vista™ Platform • Intel® Centrino® 2 processor technology, featuring: • Intel® Core™2 Duo processor* • Mobile Intel® PM45/GM45 Express Chipset* • Intel® Wireless WiFi Link 5100/5300, 5150/5350* System Memory • Dual-Channel DDR2 SDRAM support • Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules* TV Tuner • Digital TV-tuner supporting DVB-T*
Dimensions and Weight • 340.4 (W) x 247 (D) x 22.9/42.3 (H) mm (13.4 x 9.7 x 0.9/1.6 inches) • 2.4 kg (5.29 lbs.) Communication • Acer Video Conference, featuring: • Integrated Acer Crystal Eye webcam • Acer Video Conference Manager software • Acer PureZone technology • Optional Acer Xpress VoIP phone • WLAN: Intel® Wireless WiFi Link 5100/5300* • WiFi®/WiMAX™: Intel® Wireless WiFi Link 5150/5350* • WPAN: Bluetooth® 2.
• 3 USB 2.
System Block Diagram 4 Chapter 1
Your Acer Notebook tour After knowing your computer features, let us show you around your new computer. Front View No. Icon Item Description 1 Acer PureZone Two internal stereo microphones for sound recording. 2 Acer Crystal Eye Web camera for video communication. 3 Display screen Also called Liquid-Crystal Display (LCD), displays computer output. 4 Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of the computer's functions and components.
No. Icon Item Description 9 Click buttons (left, center* and right) The left and right buttons function like the left and right mouse buttons. *The center button serves as Acer Bio-Protection fingerprint reader supporting Acer FingerNav 4-way control function. 10 Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of the computer's functions and components. 11 Keyboard For entering data into your computer.
Left View No. Icon Item Description 1 Acer EasyPort IV connector Connects to Acer EasyPort IV. 2 Ethernet (RJ-45) port Connects to an Ethernet 10/100/1000-based network. 3 External display (VGA) port Connects to a display device (e.g. external monitor, LCD projector). HDMI Connects to a television or display device with HDMI input. 5 USB 2.0 ports Connect to USB 2.0 devices (e.g. USB mouse, USB camera). 6 Line-in jack Accepts audio line-in devices (e.g. audio CD player, stereo walkman).
Right View No. Icon Item Description 1 Kensington lock slot Connects to a Kensington-compatible computer security lock. 2 Optical drive Internal optical drive; accepts CDs or DVDs. 3 Optical disk access indicator Lights up when the optical drive is active. 4 Optical drive eject button Ejects the optical disk from the drive. 5 Emergency eject hole Ejects the optical drive tray when the computer is turned off.
Bottom View No. Icon Item Description 1 Battery bay Houses the computer's battery pack. 2 Battery release latch Releases the battery for removal. 3 Memory compartment Houses the computer's main memory. 4 Hard disk bay Houses the computer's hard disk (secured with screws). 5 Battery lock Locks the battery in position. 6 Ventilation slots and cooling fan Enable the computer to stay cool, even after prolonged use. Note: Do not cover or obstruct the opening of the fan.
Indicators The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed. Icon Function Description Power Indicates the computer's power status. Battery Indicates the computer's battery status. HDD Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated. Caps Lock Lights up when Caps Lock is activated. NOTE: 1. Charging: The light shows amber when the battery is charging. 2.
Touch Pad Basics (with fingerprint reader) The following items show you how to use the Touch Pad with Acer Bio-Protection fingerprint reader: • Move your finger across the Touch Pad (2) to move the cursor. • Press the left (1) and right (4) buttons located beneath the Touch Pad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the Touch Pad is the same as clicking the left button.
Using the Keyboard The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock + When Num Lock is on, the embedded keypad is in numeric mode.
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Keys The computer employs hotkeys or key combinations to access most of the computer’s controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the key before pressing the other key in the hotkey combination. Hotkey 14 Icon Function Description + Hotkey help Displays help on hotkeys. + Acer eSettings Management Launches Acer eSettings Management in Acer Empowering Technology.
Special Key You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol 1. Open a text editor or word processor. 2. Hold and then press the <5> key at the upper-center of the keyboard. NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information. The US dollar sign 1. Open a text editor or word processor. 2.
Using the System Utilities Acer Bio-Protection (only for certain models) Acer Bio-Protection Fingerprint Solution is a multi-purpose fingerprint software package integrated with the Microsoft Windows operating system.
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. AcerGridVista is simple to set up: 1. 2. 3. Run Acer GridVista and select your preferred screen configuration for each display from the task bar. Drag and drop each window into the appropriate grid.
Hardware Specifications and Configurations Processor Item Specification CPU type Intel® Penryn (dual core) CPU package Intel® 479 pin Micro-FCPGA Features Supports Intel architecture with Dynamic execution. On-die, primary 32-kB instruction cache and 32-kB write-back data cache. On-die, up to 6MB second level shared cache with advanced transfer cache architecture. Streaming SIMD Extensions 2 (SSE2),Streaming SIMD Extensions 3 (SSE3) Supplemental streaming SIMD extensions 3 (SSSE3) and SSE4.
Item Specification Features Upstream accelerated Hub architecture interface for access to GMCH. PCI Express Base Specification, Revision 1.1 support. PCI 2.3 interface. (4 PCI Request/Grant pairs). ACPI Power Management Logic Support. Enhanced DMA controller, interrupt controller, timers functions. Integrated Serial ATA host controllers with independent DMA operation on six ports and AHCI support. USB 1.1 & USB 2.0 Host controllers. Supports Intel High Definition Audio (Intel HD Audio) Interface.
System Memory Item Specification Memory controller Built-in Memory size 0MB (no on-board memory) DIMM socket number 2 sockets Supports memory size per socket 2 GB Supports maximum memory size 4G for 64bit OS (with two 2GB SODIMM) Supports DIMM type DDR II 677 Mhz /DDR III 1066 MHz SDRAM memory interface design Supports DIMM Speed 667/1066 MHz Memory module combinations You can install memory modules in any combinations as long as they match the above specifications.
Item Data heads Drive Format Disks Spindle speed (RPM) Performance Specifications Buffer size Interface Max.
Item BIOS package Specification 8 pins SOIC Supported protocols BIOS password control Set by setup manual LCD 15.4” Item Specification Vendor/model name Screen Diagonal (mm) 15.
Item Specification Features Unified Shader Architecture Support Microsoft® DirectX® 10 Shader Model 4 Geometry Instancing 2.0 SGI OpenGL® 2.
Memory Card Reader Item Specification Type JMicron JMB385 Features Support 5-in-1 Card Reader (MS,MS pro, SD, MMC, xD) Compliant with SD Memory Card Specification Version 2.0 Compliant with MultiMediaCard Specification Version 4.1 Compliant with Memory Stick Standard Format Specification Version 1.4 Compliant with Memory Stick PRO Format Specification Version 1.00 Compliant with xD Picture Card Specification Version 1.20 Compliant with xD Picture Card Host Guideline Version 1.
Bluetooth Interface Item Specification Chipset FOXCON T60H928.11 Bluetooth miniUSB module Features Internal Mini USB solution with antenna Bluetooth 2.
Item 26 Specification Normal voltage 11.1V Charge voltage 16.
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Information The Information screen displays a summary of your computer hardware information. Information Main InsydeH20 Setup Utility Advanced Security Power Rev. 3.5 Boot Exit CPU Type: CPU Speed: Intel (R) Core (TM)2 Duo CPU @ 2.40GHz 2.40GHz HDD Model Name: HDD Serial Number: ATAPI Model Name: Hitachi HTS543516K9SA00 071129BB0C02WGHDKKGC Slimtype DVD A DS8A2S System BIOS Version: VGA BIOS Version: Serial Number: Asset Tag Number: Product Name: Manufacturer Name: UUID: V0.
Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. Information Main InsydeH20 Setup Utility Advanced Security Power System Time System Date [13:04:04] [04/21/2008] Total Memory Video Memory 3017 MB [32MB] Quick Boot Network Boot F12 Boot Menu D2D Recovery SATA Mode [Enabled] [Enabled] [Disabled] [Enabled] [ACHI] F1 Help ESC Exit ↑↓ Select Item ←→ Select Menu Boot Rev. 3.
Advanced The Advanced screen allows the user to configure the various advanced BIOS options. IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless you have experience adjusting these items, we recommend that you leave these settings at the default values. If making settings to items on these pages causes your system to malfunction or prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to boot up normally.
Parameter Description Submenu Items USB Configuration Enter the USB Configuration menu. • • • • USB Driver Select EHCI 1 and 2 UHCI 1 to 5 Per-Port Control Chipset Configuration Enter the Chipset Configuration menu. • • • • Port 80h Cycles DMI Link ASPM Control PCI Latency Timer VT-d ACPI Table/ Features Control Enter the ACPI Table/Features Control menu.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Information Main InsydeH20 Setup Utility Advanced Security Power Supervisor Password Is: User Password Is: HDD Password Is: Clear Clear Clear Set Supervisor Password Set User Password Set Hdd Password Power on password [32MB] F1 Help ESC Exit Boot Rev. 3.5 Exit Item Specific Help Install or Change the password and the length of password must be less than eight words.
Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears: 2. Type a password in the “Enter New Password” field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.
Changing a Password 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears. 2. Type the current password in the Enter Current Password field and press Enter. 3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. 4. Press Enter. After setting the password, the computer sets the User Password parameter to “Set”. 5. If desired, you can enable the Password on boot parameter.
Power The Power screen allows the user to configure various CPU and power management options and device wakeup behavior. Information InsydeH20 Setup Utility Advanced Security Power Main Boot XAdvanced CPU Control XPlatform Power Management ACPI S3: Wake on PME Wake on Modem Ring Auto wake on S5 Quickly S4 Resume F1 Help ESC Exit ↑↓ Select Item ←→ Select Menu Rev. 3.5 Exit Item Specific Help These items control various CPU parameters.
Parameter 36 Description Submenu Items Platform Power management Enter the Platform Power Management menu. • • • PCI Clock Run _CST - C4 Latency Value C4 on C3 - Deeper Sleep ACPI S3 Enable or Disable ACPI S1/S3 Sleep State N/A Wake on PME Enable or Disable wake up when the system power is off and a PCI Power Management Enable wake up event occurs. N/A Wake on Modem Ring Enable or Disable wake up when the system power is off and a modem attached to the serial port is ringing.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay. Information Main InsydeH20 Setup Utility Advanced Security Power Boot priority order: 1. IDE0 : Hitachi HTS542516K9SA00 2. IDE1 : Slimtype DVD A DS8A2S 3 . USB FDD : 4. Network Boot : Realtek Boot Agent 5. USB HDD : 6.
Exit The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility. Information Main InsydeH20 Setup Utility Advanced Security Power Boot Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help ESC Exit ↑↓ Select Item ←→ Select Menu Rev. 3.5 Exit Item Specific Help Exit System Setup and save your changes to CMOS.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
Remove HDD/BIOS Utility This section provide you with removing HDD/BIOS method: Remove HDD Password: • If you key in wrong HDD password three times, HDD password error code displays. See the image below. To reset the HDD password, run HDD_PW.EXE as follows: 1. Key in hdd_pw 15494 0 2. Press 2. 3. Select one upper-case string from the list. 4. Reboot system and key in the selected string (0KJFN42 or UVEIQ96) on the HDD User Password screen.
Remove BIOS Password: If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the image below. To reset the BIOS password, run BIOS_PW.EXE as follows: 1. Key in bios_pw 14452 0 2. Select one string from the list.
3. Reboot the system and key in the selected string (qjjg9vy, 07yqmjd etc.) for the BIOS user password.
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.
General Information Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, stable surface. 4. Remove the battery pack.
External Module Disassembly Process External Modules Disassembly Flowchart The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order. Screw List Step Screw Quantity Color Part No. Memory Cover M2.
Removing the Battery Pack 1. Turn computer over. 2. Slide the battery lock/unlock latch to the unlock position. 3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main unit (2).
Removing the SD dummy card 1. Push the SD dummy card all the way in to eject it. 2. Pull it out from the slot.
Removing the ExpressCard dummy card 1. Push the ExpressCard dummy card all the way in to eject it. 2. Pull it out from the slot.
Removing the Lower Covers 1. See “Removing the Battery Pack” on page 46. 2. See “Removing the Lower Covers” on page 49. 3. See “Removing the Lower Covers” on page 49. 4. Loosen the ten captive screws from the Memory, HDD1, and HDD2 Covers. Memory Cover HDD1 Cover HDD2 Cover 5. Carefully open the memory cover. 6. Remove the HDD1 cover as shown.
7. Remove the HDD2 cover as shown. Removing the DIMM Modules 1. See “Removing the Battery Pack” on page 46. 2. Remove the Memory Module cover. See “Removing the Lower Covers” on page 49. 3. Push out the release latches on both sides of the DIMM socket to release the DIMM module. 4. Remove the DIMM module. 5. Repeat steps for the second DIMM module.
Removing the MXM Module 1. See “Removing the Battery Pack” on page 46. 2. Remove the Memory Module cover. See “Removing the Lower Covers” on page 49. 3. Remove the four securing screws. Step WLAN Module Size M2.5*9 (NL) Quantity Screw Type 4 4. Grasp the module and remove. Removing the Turbo RAM module 1. See “Removing the Battery Pack” on page 46. 2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49.
3. Remove the three securing screws. Step WLAN Module Size M2*3 (NL) Quantity Screw Type 3 4. Remove the bracket from the module. 5. Remove the Turbo RAM Module. NOTE: Some models come equipped with either a TV Tuner module or a Turbo RAM module.
Removing the TV Tuner module 1. See “Removing the Battery Pack” on page 46. 2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49. 3. Disconnect the TV Tuner cable from the module. 4. Remove the three securing screws.
5. Remove the bracket from the module. 6. Remove the TV Tuner module. NOTE: Some models come equipped with either a TV Tuner module or a Turbo RAM module. Removing the WLAN Module 1. See “Removing the Battery Pack” on page 46. 2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49. 3. Remove the Turbo RAM. See “Removing the TV Tuner module” on page 53. 4. Disconnect the antenna cables from the WLAN board.
NOTE: The following is the correct cable-color to connector designation: TR1 (left) to White, TR3 (middle) to Gray, and TR2 (right) to Black. 5. Move the cables away to avoid damaging the them, and remove the two screws on the WLAN board to release the WLAN board. Step WLAN Module Size M2*3 (NL) Quantity Screw Type 2 6. Detach the WLAN board from the WLAN socket. Removing the Hard Disk Drive1 Module 1. Remove the Battery Pack. See “Removing the Battery Pack” on page 46. 2. Remove the HDD1 cover.
3. Remove the two securing screws. Step HDD Carrier Size M2*3 (NL) Quantity Screw Type 2 4. Use the pull-tab to lift up the HDD1 module to remove. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
5. Remove the four screws (two each side) securing the HDD to the carrier. Step HDD Carrier Size M2*3 (NL) Quantity Screw Type 4 6. Turn the HDD module upside down, and lift the HDD carrier up.
Removing the Hard Disk Drive2 Module 1. See “Removing the Battery Pack” on page 46. 2. Remove the HDD2 cover. See “Removing the Lower Covers” on page 49. 3. Remove the two securing screws. Step HDD Carrier Size M2*3 (NL) Quantity Screw Type 2 4. Use the pull-tab to lift up the HDD module and remove. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
5. Remove the four screws (two each side) securing the HDD to the carrier. Step HDD Carrier Size M2*3 (NL) Quantity Screw Type 4 6. Turn the HDD module upside down, and lift the HDD carrier up. 7. Remove the connector from the HDD.
Removing the Optical Drive Module 1. See “Removing the Battery Pack” on page 46. 2. Remove the Memory cover. See “Removing the Lower Covers” on page 49. 3. Loosen the captive screw securing the ODD module and remove the ODD cap. 4. Carefully use a screwdriver to push the locking catch and remove the ODD module. 5. Grasp the module and pull out from the main unit.
6. Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive module. Step ODD Bracket Size M2*2.5(NL) Quantity Screw Type 2 7. Insert a pin in the eject hole of the ODD to eject the ODD tray. 8. Press down on the locking catch to release the ODD cover and remove.
Main Unit Disassembly Process Main Unit Disassembly Flowchart Screw List Step 62 Screw Quantity Color Part No. Switch Cover M2*3 (NL) 2 MA0000060G0 LCD Module M2.5*8(NL) 4 MA000005YG0 LCD Module M2.5*5 (NL) 2 MA000007YG0 Upper Cover M2.5*8 (NL) 8 MA000005YG0 Upper Cover M2.5*5 (NL) 7 MA000007YG0 Touch Pad Bracket M2*3 (NL) 2 MA0000060G0 Launch Board M2*3 (NL) 2 MA0000060G0 Speaker M2*3 (NL) 4 MA0000060G0 I/O Board M2.
Removing the Switch Cover CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1. Remove the Battery Pack. See “Removing the Battery Pack” on page 46. 2. Locate and remove the nine securing screws as shown. Step Size Quantity Switch Cover M2.5*3(NL) Blue Callout 4 Switch Cover M2.5*6.5(NL) Red Callout 5 Screw Type 3.
Removing the Switch Board 1. Remove the Switch Cover. See “Removing the Switch Cover” on page 63. 2. Remove the two securing screws from the Switch Board. Step Switch Board Size M2*3 (NL) Quantity Screw Type 2 3. Disconnect the Switch Board to Ekey board FFC cable as shown. 4. Use the tweezers to secure the cable in place, then remove the Switch Board away from the top cover.
Removing the Keyboard 1. Remove the Switch Cover. See “Removing the Switch Cover” on page 63. 2. Grasp the keyboard and lift up to remove. 3. Lift the keyboard over and disconnect the keyboard FFC. 4. Remove the keyboard and place it on a clean surface. Removing the Modem Module 1. Remove the Keyboard. See “Removing the Keyboard” on page 65.
2. Remove the two securing screws. Step Modem Module Size M2*3 (NL) Quantity Screw Type 2 3. Using a plastic pry, partially lift up the module to expose the connector. 4. While holding the module, use the plastic tweezers to hold the connector and pull the module away to remove.
Removing the Antenna, MIC and Speaker Cables IMPORTANT:Ensure the Antenna Cables are free of any obstructions before attempting to remove. 1. Remove the WLAN Module. See “Removing the WLAN Module” on page 54. 2. Remove the HDD2 Module. See “Removing the Hard Disk Drive2 Module” on page 58. 3. Remove the MXM Module. See “Removing the MXM Module” on page 51. 4. Remove the Keyboard. See “Removing the Keyboard” on page 65. 5. Gently pull the Antenna Cables through the HDD housing. 6.
7. Gently pull the MIC and Speaker cables through the HDD housing. 8. Turn the computer on its side, and feed cables through to the upperside. 9. Pull the cables completely through. Remove Keyboard from this image.
Removing the LCD Module 1. Remove the Battery Pack. See “Removing the Battery Pack” on page 46. 2. Remove the SD dummy card. See “Removing the Lower Covers” on page 49. 3. Remove the Express dummy card. See “Removing the Lower Covers” on page 49. 4. Remove the Lower Covers. See “Removing the Lower Covers” on page 49. 5. Remove the DIMM Modules. See “Removing the DIMM Modules” on page 50. 6. Remove the WLAN Module. See “Removing the WLAN Module” on page 54. 7. Remove the HDDs.
13. Remove the single ground screw and four securing screws (two each side) connecting the LCD module. Step Size Quantity LCD Module M2.5*6.5 (NL) Red Callout 4 Ground M2.5*3 (NL) Blue Callout 1 Screw Type 14. Carefully remove the LCD module from the chassis.
Removing the Upper Cover 1. See “Removing the LCD Module” on page 69. 2. Place the computer upside down and remove the remaining eleven screws on the bottom panel. Step LCD Module Size M2.5*6.5(NL) Quantity Screw Type 11 3. Turn the computer over and loosen the captive screw from the keyboard plate. 4. Remove the keyboard plate. If necessary, use a plastic pry to lift the plate.
5. Disconnect the five cables from the mainboard as shown. A B E C D IMPORTANT:When removing cables, always hold the cable by the pull-tab or by the connector. Do not hold the pull by the cable itself to prevent stripping. 72 Disconnect A as shown. Release the securing latches and disconnect B as shown. Release the securing latches and disconnect C as shown. Release the securing latches and disconnect D as shown.
Release the securing latches and disconnect E as shown. 6. Remove the four securing screws from the upper cover. 7. Grasp the Upper Cover by the hinge socket and pry it open. Do not lift the cover completely off. NOTE: Do not try to pry open more than one edge at a time. 8. While holding the cover open, pull through any remaining cables.
9. Grasp the cover by the opposite edge and lift up to remove the Upper Cover.
Removing the Touch Pad 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Remove the Speaker Module. See “Removing the Speaker Module” on page 79. 3. Remove the Finger Print Reader Module. See “Removing the Finger Print Reader” on page 76. 4. Remove the Launch Board Module. See “Removing the Launch Board” on page 77. 5. Remove the Launch Board Module. See “Removing the Launch Board” on page 77. 6. Disconnect the Touch Pad cable from the Touch Pad board.
Removing the Finger Print Reader 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Disconnect the cable as shown. 3. Disconnect the two FFC cables as shown. 4. Remove the four securing screw from the Finger Print Reader board.
5. Remove the bracket from the board. 6. Remove the Finger Print Reader board from the Upper Cover. Removing the Launch Board 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Lift up the locking latch and remove the FFC cable as shown. 3. Remove the four screws from the Launch Board.
Step Launch Board Size M2*3 (NL) Quantity Screw Type 4 4. Remove the Launch Board from the Upper Cover.
Removing the Speaker Module 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Remove four securing screws connecting the Speaker Module. Step Speaker Module Size M2*6 (NL) Quantity Screw Type 4 3. Remove the Speaker Module from the upper cover. Removing the eKey Module 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Turn the Upper Cover upside down and remove the two securing screws connecting the eKey module. 3. Disconnect the eKey Module cable.
Step Speaker Size M2*3 (NL) Quantity Screw Type 2 4. Remove the module as shown.
Removing the Bluetooth board 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Remove the securing screw from the Bluetooth board. Step Bluetooth Board Size M2*3 (NL) Quantity Screw Type 1 3. Lift the Bluetooth board away from the main board and disconnect the mainboard cable. 4. Disconnect the cable from the mainboard.
Removing the Subwoofer Module 1. See “Removing the Upper Cover” on page 71. 2. Remove the four securing screws from the Subwoofer Module. Step Subwoofer Module Size M2.5*4 (NL) Quantity Screw Type 4 3. Grasp the cable by the end and guide it out of its housing as shown in the following images. IMPORTANT:The housing guides are hooked to hold the cable in place. Do not pull the cable to remove it or damage can occur.
4. Grasp the Subwoofer Module and lift it up to remove. Removing the ExpressCard Module 1. See “Removing the Upper Cover” on page 71. 2. Remove the two securing screws. IMPORTANT:Do not grasp the cable itself to prevent fraying. Step Modem Module Size M2*3 (NL) Quantity Screw Type 2 3. Disconnect the cable connecting the ExpressCard module.
4. Lift the ExpressCard module away from the upper cover.
Removing the Mainboard 1. Remove the Upper Cover. See “Removing the Upper Cover” on page 71. 2. Use the tweezers to lift and remove the tape strip securing the modem cable. 3. Disconnect the two cables connected to the motherboard. 4. Remove the securing screw from the Mainboard. Step Mainboard Chapter 3 Size M2.5*6.
5. Pull the edge of the lower base outward and lift the motherboard up to remove. Removing the CPU Fan Module 1. See “Removing the Battery Pack” on page 46. 2. Remove the Mainboard. See “Removing the Mainboard” on page 85. 3. Turn the Mainboard right side up, and place it on a clean surface. 4. Using tweezers, grip the cable connector and disconnect the Fan cable from the Mainboard. IMPORTANT:Do not grip the cable itself to prevent stripping. 5. Loosen the three captive screws from the heatsink.
6. Lift the cover to expose the single securing screw. Remove the screw. Step Mainboard Size M2.5*6.5 (NL) Quantity Screw Type 1 7. Lift the Fan module clear of the Mainboard. Removing the CPU 1. Remove the CPU Fan Module. See “Removing the CPU Fan Module” on page 86.
2. Using a flat screwdriver, turn the CPU socket latch clockwise 180° to release the CPU. k 3. Lift the CPU clear of the Mainboard.
LCD Module Disassembly Process LCD Module Disassembly Flowchart Screw List Step Screw LCD Bezel M2.5*5 (NL) 4 Black MA000007YG0 Inverter Board M2.5*5 (NL) 1 Black MA000007YG0 Camera Module M2*3 (NL) 2 Black MA0000060G0 LCD Panel M2.5*5 (NL) 2 Black MA000007YG0 LCD Brackets M2*3 (NL) 8 Black MA0000060G0 Chapter 3 Quantity Color Part No.
Removing the LCD Bezel 1. Remove the LCD Module. See “Removing the LCD Module” on page 69. 2. Remove the six rubber covers and screws. Step LCD Bezel Size M2.5*6.5 (NL) Quantity Screw Type 6 3. Starting from the inside edges, pry the inside of the bezel upwards from the panel. Continue moving left until the bezel is removed. If necessary, use a plastic pry to release the corners of the bezel.
4. Lift up the bezel and remove it from the LCD Module. Removing the Inverter Board 1. Remove the LCD Bezel. See “Removing the LCD Bezel” on page 90. 2. Disconnect the left and right Inverter board cables as shown. 3. Lift up the Inverter Board and remove.
Removing the Camera Module 1. Remove the LCD Bezel. See “Removing the LCD Bezel” on page 90. 2. Remove the two securing screws from the Camera Module. Step Camera Module Size M2*3 (NL) Quantity Screw Type 1 3. Disconnect the Camera Module cable as shown.
Removing the LCD Panel 1. Remove the LCD Bezel. See “Removing the LCD Bezel” on page 90. 2. Remove the six securing screws from the LCD Module. Step LCD Panel Size M2.5*6.5 (NL) Quantity Screw Type 6 3. Disconnect the left and right sides of the Inverter cable. 4. Disconnect the Camera Module cable as shown.
5. Grasp the panel by both ends and lift to remove. Removing the LCD Brackets and FPC Cable 1. Remove the LCD Panel. See “Removing the LCD Panel” on page 93. 2. Turn the LCD panel over to expose the rear. Grip the FPC cable and lift upward to detach the adhesive pads. 3. Remove the eight securing screws (four on each side) from the LCD Panel brackets.
4. Remove the LCD brackets by pulling away from the LCD Panel as shown.
LCD Module Reassembly Procedure Replacing the LCD Panel 1. Align the LCD brackets with the eight screw holes (four on each side) on the LCD Panel as shown. 2. Secure the LCD brackets to the LCD panel. 3. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown.
4. Align the LCD Panel cable as shown and press down to secure in place. 5. Take care to insert the top of the panel fist and then 6. Place the LCD Panel in the back cover. angle the it in place. 7. Secure the LCD module with the six securing screws.
8. Connect the left and right Inverter cables. 9. Connect the camera cable.
Replacing the LCD Bezel 1. Starting from the bottom, locate the bezel correctly and press down the edges until there are no gaps between the bezel and the LCD Module, 2. Replace the six screws and the rubber screw caps provided.
Main Module Reassembly Procedure Replacing the CPU 1. Carefully turn the mainboard upside down (CPU 2. Using a plastic screw driver, lock the CPU in the side up), and insert the CPU into the CPU bracket socket as shown. as shown. Replacing the CPU Fan Module 1. Replace the Fan module on the Mainboard. 2. Lift the cover to replace the single screw located in the back of the fan module. 3. Tighten the three captive screws on the heatsink. 4. Connect the Fan cable to the Mainboard.
Replacing the Mainboard 1. Pull the edge of the lower base outward and insert the motherboard in the lower base. 2. Replace the securing screw on the Mainboard. 3. Connect the two cables connected to the motherboard. 4. Replace the adhesive strip securing the modem cable.
Replacing the Bluetooth Board 1. Connect one end of the Bluetooth cable to the mainboard as shown. 2. Connect the other end of the Bluetooth cable to the Bluetooth Module as shown. 3. Locate the Bluetooth Module and replace the single securing screw. Replacing the ExpressCard Module 1. Replace the ExpressCard module on the upper cover. 2. Replace the two securing screws. IMPORTANT:The correct location of the ExpressCard Module screws is illustrated in the following image.
3. Connect the cable connecting the ExpressCard module. Replacing the Subwoofer Module 1. Grasp the Subwoofer Module and insert in the lower base. 2. Insert the cables under the housing guide as shown.
3. Replace the four securing screws on the Subwoofer Module. Replacing the Finger Print Reader 1. Remove the Finger Print Reader board from the Upper Cover.
2. Remove the bracket from the board. 3. Replace the four securing screw on the Finger Print Reader board. NOTE: Move back the cabling to allow for easier access to the screw sockets. 4. Connect the two FFC cables as shown.
5. Connect the cable as shown. Replacing the eKey Module IMPORTANT:Take note of the eKey button when installing. It must face down and the cable connector up in order to install the module correctly. 1. Locate and replace the module as shown. 2. Connect the eKey Module cable and replace the two securing screws.
Replacing the Touch Pad IMPORTANT:The Touch Pad cannot be removed individually. To replace the Touch Pad, replace the entire Upper Cover. 1. Connect the Touch Pad cable as shown Replacing the Launch Board 1. Replace the Launch Board on the upper cover. 2. Replace the four securing screws. 3. Insert the FFC flush with the connector and press down on the locking latch to secure.
Replacing the Switch Board 1. Connect the cable to the Switch Board. 2. Insert the eKey board FFC flush with the connect and press down on the locking latch to secure. 3. Replace the two securing screws on the Switch Board.
Replacing the Antenna, MIC and Speaker Cables IMPORTANT:Ensure that all cables pass through the Mainboard and are accessible from the underside of lower cover. 1. Insert the cabling through the housing as shown. 2. Ensure that the cabling is tucked in and secured. 3. Turn the computer on its side, feed cables through to the underside. 4. Place the computer upside down, and insert the MIC and Speaker cables through the HDD housing. 5. Take note of the cabling arrangement.
6. Connect the MIC and speaker cables. 7. Gently pull the Antenna Cables through the HDD housing.
Replacing the Speaker Module 1. Replace the Speaker Module from the upper cover. 2. Replace the four securing screws connecting the Speaker Module. Replacing the Upper Cover 1. Locate the upper cover over the lower base taking note of the screw sockets.
2. Angle the right end of the Upper Cover in place, and insert any remaining cables through the lower base as shown. 3. Set the Upper Cover down on the lower base. 4. Replace the four securing screws on the Upper Cover.
5. Connect the five cables from the mainboard as shown. A B E C D IMPORTANT:When removing cables, always hold the cable by the pull-tab or by the connector. Do not hold the pull by the cable itself to prevent stripping. Connect A as shown. Connect B as shown. Connect C as shown. Connect D as shown.
Connect E as shown. 6. Angle the keyboard plate to insert. 7. Tighten the captive screw on the keyboard plate.
8. Turn the computer upside down and replace the eleven securing screws on the bottom panel to attach the bottom and lower covers. Replacing the Modem Module 1. Angle the Modem Module in place and attach to the connector. 2. Insert the module and replace the two securing screws.
Replacing the Keyboard 1. Replace keyboard cable to the mainboard, and secure the locking latch. 2. Turn the keyboard over and place the front edge first in the mounting. 3. Press down on the areas marked below to secure in place.
Replacing the Switch Cover 1. Replace the Switch cover, and press down to secure in place. 2. Turn the computer over and replace the nine securing screws.
Replacing the ODD Module 1. Insert a pin in the eject hole of the ODD to eject the 2. Press the cover into the tray, bottom edge first, to ODD tray. secure. 3. Turn ODD Module around and secure bracket with 4. Slide Module in chassis and press until Module is two screws. flush with chassis. 5. Replace the ODD Cap and secure the single captive screw.
Replacing the Hard Disk Drive2 Module 1. Replace the connector on the HDD. 2. Place the HDD in the HDD carrier. 3. Replace the four screws (two each side) to secure 4. Insert the HDD, right side first, and push down to the carrier. locate the interface correctly. 5. Replace the two securing screws.
Replacing the Hard Disk Drive1 Module 1. Replace the connector on the HDD. 2. Place the HDD in the HDD carrier. 3. Replace the four screws (two each side) to secure 4. Insert the HDD, left side first, and push down to the carrier. locate the interface correctly. 5. Replace the two securing screws.
Replacing the WLAN Board 1. Insert the WLAN board in to the socket. 2. Push the board down and replace the two securing screws. 3. Replace the three antenna cables. NOTE: The following is the correct cable-color to connector designation: TR1 (left) to White, TR3 (middle) to Gray, and TR2 (right) to Black.
Replacing the TV Tuner Module 1. Insert the TV Tuner board in to the socket. 2. Attach the bracket to the module. 3. Replace the three securing screws. 4. Replace the antenna cable.
Replacing the Turbo Ram Module. 1. Insert the Turbo Ram board in to the socket. 2. Attach the bracket to the module. 3. Replace the three securing screws. Replacing the MXM Module 1. Insert the MXM board in to the socket. Chapter 3 2. Replace the four securing screws.
Replacing the DIMM Modules 1. Insert DIMM1 in to the socket. 2. Press down to locate DIMM correctly. Requires new image 3. Repeat steps 1 and 2 for the second DIMM module. Replacing the Lower Covers 1. Replace the HDD2 cover. 2. Replace the HDD1 cover. 3. Replace the Memory cover. 4. Secure the ten captive screws in the covers.
Replacing the ExpressCard Dummy Tray 1. Insert the ExpressCard dummy as shown. 2. Push into the slot until flush with the chassis cover. Replacing the SD Dummy Tray 1. Insert the SD dummy as shown. 2. Push into the slot until flush with the chassis cover. Replacing the Battery 1. Slide and hold the battery release latch (1), insert battery in to the main unit (2). 2. Slide the battery lock/unlock latch to the lock position.
126 Chapter 3
Chapter 4 Troubleshooting Common Problems Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
Power On Issue If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Computer Shutsdown Intermittently If the system powers off at intervals, perform the following actions one at a time to correct the problem. 128 1. Check the power cable is properly connected to the computer and the electrical outlet. 2. Remove any extension cables between the computer and the outlet. 3.
No Display Issue If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: No POST or Video If the POST or video doesn’t display, perform the following actions one at a time to correct the problem. 1. Make sure that the internal display is selected. On this notebook model, switching between the internal display and the external display is done by pressing Fn+F5. Reference Product pages for specific model procedures. 2.
Abnormal Video Display If video displays abnormally, perform the following actions one at a time to correct the problem. 1. Reboot the computer. 2. If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and should be replaced. See “Disassembly Process” on page 44. 3. If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD is faulty and should be replaced. See “Disassembly Process” on page 44. 4.
LCD Failure If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs: Built-In Keyboard Failure If the built-in Keyboard fails, perform the following actions one at a time to correct the problem.
Touch Pad Failure If the Touch Pad doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to correct the problem.
Sound Problems If sound problems are experienced, perform the following actions one at a time to correct the problem. 1. Reboot the computer. 2. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check the Device Manager to determine that: • The device is properly installed. • There are no red Xs or yellow exclamation marks. • There are no device conflicts. • No hardware is listed under Other Devices. 3.
Internal Microphone Failure If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Microphone Problems If internal or external Microphones do no operate correctly, perform the following actions one at a time to correct the problem. 1. Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´ Sound and select the Recording tab. 2.
HDD Not Operating Correctly If the HDD does not operate correctly, perform the following actions one at a time to correct the problem. 1. Disconnect all external devices. 2. Run a complete virus scan using up-to-date software to ensure the computer is virus free. 3. Run the Windows Vista Startup Repair Utility: a. insert the Windows Vista Operating System DVD in the ODD and restart the computer. b. When prompted, press any key to start to the operating system DVD. c.
ODD Failure If the ODD fails, perform the following actions one at a time to correct the problem.
a. Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device and click Enable. b. Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and click Enable. c. Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver. d.
b. Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0. c. Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is checked and click OK. d. Repeat for the other ATA Devices shown if applicable. Drive Not Detected If Windows cannot detect the drive, perform the following actions one at a time to correct the problem. 1. Restart the computer and press F2 to enter the BIOS Utility. 2.
USB Failure (Rightside) If the rightside USB port fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Modem Function Failure If the internal Modem fails, perform the following actions one at a time to correct the problem.
Wireless Function Failure If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs: EasyTouch Button Failure If the Acer EasyTouch buttons fail, perform the following actions one at a time to correct the problem.
MediaTouch Button Failure If the Acer MediaTouch buttons fail, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Fingerprint Reader Failure If the Fingerprint Reader fails, perform the following actions one at a time to correct the problem.
Thermal Unit Failure If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: HDTV Switch Failure If the HDTV Switch fails, perform the following actions one at a time to correct the problem.
External Mouse Failure If an external Mouse fails, perform the following actions one at a time to correct the problem. 1. Try an alternative mouse. 2. If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See the mouse user manual. 3. If the mouse uses a USB connection, try an alternate USB port. 4. Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure. 5. Restart the computer. 6.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
POST Codes Tables These tables describe the chipset and core POST codes, functions, phases, and components for the POST. Chipset POST Codes The following table details the chipset POST codes and functions used in the POST.
POST Code Function Phase Component 0x32 Program the Egress port timings PEI chipset/MRC 0x33 Program the Memory IO registers PEI chipset/MRC 0x34 Perform steps required before JEDEC PEI chipset/MRC 0x35 Perform JEDEC memory initialization for all memory rows PEI chipset/MRC 0x36 Setup DRAM control register for normal operation and enable PEI chipset/MRC 0x37 Do ZQ calibration for DDR3 PEI chipset/MRC 0x38 Perform final Dra/Drb programming, Set the mode of operation for the memor
POST Code Function Phase Component 0xF3 #define MEM_ERR_RCVEN_FINDCENTER (CalibrateRcvenForGroup) PEI chipset/MRC 0xFZ #define MEM_ERR_TYPE (S11, S04) PEI chipset/MRC 0xF5 #define MEM_ERR_RAWCARD (S11) PEI chipset/MRC 0xFA #define MEM_ERR_SFF (ProgWrioDll) PEI chipset/MRC 0xFB #define MEM_ERR_THERMAL (ProgramThrottling) PEI chipset/MRC 0xA0xx Launch BIOS ACMSclean PEI chipset/TXT 0xA4xx Launch BIOS ACMScheck PEI chipset/TXT 0xE5 Wait for ME ready DXE HECI/iAMT 0xE6 ME Re
POST Code Function Phase Component 0x82 Initialize the CPU Crisis Recovery Core 0x89 Set Huge Segment Crisis Recovery Core 0x83 Initialize system timer Crisis Recovery Core 0x84 Initialize system I/O Crisis Recovery Core 0x88 Initialize Multi Processor Crisis Recovery Core 0x8A Initialize OEM special code Crisis Recovery Core 0x8B Initialize PIC and DMA Crisis Recovery Core 0x8C Initialize Memory type Crisis Recovery Core 0x8D Initialize Memory size Crisis Recovery Cor
POST Code Function Phase Component 0x09 TCG log event failed DXE TCG 0x09 Setup event log failed DXE TCG 0x12 TIS set active locality failed DXE TCG 0x12 TIS relinquish active locality failed DXE TCG 0x12 TIS wait command ready failed (prepare to send) DXE TCG 0x12 TIS abort 'send 'command due to timeout DXE TCG 0x12 TIS abort 'sendAndGo 'command due to timeout DXE TCG 0x04 TIS wait bit set failed before send last byte DXE TCG 0x12 TIS abort command due to timeout before
POST Code Function Phase Component 0x1A Initialize DMA command register with these settings: 1. Memory to memory disabled 2. Channel 0 hold address disabled 3. Controller enabled 4. Normal timing 5. Fixed priority 6. Late write selection 7. DREQ sense active 8. DACK sense active low. LBT Core 0x22 Reset the keyboard. LBT Core 0x40 Test A20 line LBT Core 0x67 Quick initialization of all Application Processors in a multi-processor system LBT Core 0x32 Compute CPU speed.
POST Code Function Phase Component 0x4C Shadow video BIOS ROM if specified by Setup, and CMOS is valid and the previous boot was OK. LBT Core 0x59 Register POST Display Services, fonts, and languages with the POST Dispatch Manager. LBT Core 0x57 Initialize 1394 Firewire LBT Core 0xD6 Initialize PC card LBT Core 0x58 Test for unexpected interrupts. First do an STI for hot interrupts. Secondly, test the NMI for an unexpected interrupt.
POST Code Function Phase Component 0x6A Display external cache size on the screen if it is nonzero. LBT Core 0x6C Display shadow message LBT Core 0xCA post EISA init LBT Core 0x70 Check flags in CMOS and in the TrustedCore data area for errors detected during POST. Display error messages on the screen. LBT Core 0x72 Check status bits to see if configuration problems were detected. If so, display error messages on the screen. LBT Core 0x4F Initialize MultiBoot.
POST Code Function Phase Component 0x8B Setup interrupt vector and present bit in Equipment byte. LBT Core 0x95 1. Check CMOS for CD-ROM drive present 2. Activate the drive by checking for media present 3. Check sector 11h (17) for Boot Record Volume Descriptor 4. Check the boot catalog for validity 5. Pick a boot entry 6. Create a Specification Packet LBT Core 0x92 Jump to UserPatch2. LBT Core 0xB6 If password on boot is enabled, a call is made to Setup to check password.
POST Code Function Phase Component 0xB5 Fade out OEM Logo or post string LBT Core 0xC5 End hotkey detection (Server BIOS) LBT Core 0xBE If BCP option is enabled, clear the screen before booting. LBT Core 0xB6 If password on boot is enabled, a call is made to Setup to check password. If the user does not enter a valid password, Setup does not return. LBT Core 0xBC Clear parity-error latch LBT Core 0xB7 Initialize ACPI BIOS.
Chapter 5 Jumper and Connector Locations Top View 1 2 3 4 5 6 8 7 No. Chapter 5 Description No.
Bottom View 1 2 3 17 16 15 14 13 4 12 11 10 5 9 8 No. 156 Description 7 6 No.
Clearing Password Check and BIOS Recovery This section provide you the standard operating procedures of clearing password and BIOS recovery for Aspire 7730/7730G. Aspire 7730/7730G provide one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.
BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. BIOS Recovery Hotkey: The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered on during BIOS POST.
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 7730/7730G. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Aspire 7730/7730G Exploded Diagrams Upper Cover Number Description Part Number 1 2 3 4 5 6 7 160 Chapter 6
Lower Cover Number Description Part Number 1 2 3 4 Chapter 6 161
LCD Panel Number Description Part Number 1 2 3 4 5 6 7 8 9 10 162 Chapter 6
Aspire 7730/7730G FRU List Category Description Part Number Adapter ADAPTER 65W 3PIN DELTA SADP-65KB DFA AP.06501.013 ADAPTER 65W LITEON PA-1650-02AC LF AP.06503.016 ADAPTER 65W 3PIN HIPRO AC-OK065B13 AP.0650A.010 ADAPTER DELTA 90W ADP-90SB BBEA LF AP.09001.013 ADAPTER LITE-ON 90W 19V BLUE PA-1900-24AR LED LF AP.09003.011 ADAPTER HIPRO 90W 19V BLUE HP-OL093B13P LED LF LEVEL 4 AP.0900A.001 Battery SONY AS-2007B Li-Ion 3S2P SONY 6 cell 4400mAh Main COMMON Normal Type BT.00604.
Category Description Part Number NEWCARD BOARD 55.TPK07.004 MSI VGA Card nVidia NB9P-GS DDRIII 512M 800MHz 32*32 MXM II w/ HDCP w/ Intersil PowerIC VG.9PG06.002 MSI VGA Card nVidia NB9M-GS DDRII 256M 400MHz 32*16 MXM I w/ HDCP w/ Intersil PowerIC VG.9MG06.001 DVB-T MINI TUNER CARD A310 W/CONN & ADA TU.23100.010 INVERTER BOARD 19.TPK07.001 PWR CORD V943B30001218008 DANISH 3P 27.A03V7.006 PWR CORD (ISR) 1.8M 3PBLK FZ0I0008-038 27.TATV7.005 PWR CORD V50CB3T3012180QD TW-110V,3P 27.A99V7.
Category Description Part Number Assembly Parts MIDDLE COVER Chapter 6 42.AR907.001 UPPER CASE W/SPEAKER, FFC, CABLE,TP FOR NON-FP 60.AS307.001 UPPER CASE W/SPEAKER, FFC, CABLE,TP FOR FP 60.AR907.001 LOWER CASE ASSY W/SUB-WOOF,RJ11 W/O TV 60.AR907.002 LOWER CASE ASSY W/SUB-WOOF,RJ11,TV OUT CABLE 60.AS307.002 RAM COVER 42.AR907.002 HDD COVER -1 42.AR907.003 HDD COVER - 2ND 42.AR907.004 DDR BRACKET 33.AR907.001 TP BRACKET 33.AR907.002 ODD CAP 42.AR907.007 VGA SUPPORT BRACKET 33.
Category Description Part Number LCD BEZEL TEXTURE FOR CCD LCD COVER HOLO 3D MIMO W/ 3 ANTENNA 60.AR907.004 LCD BEZEL PAINTING FOR CCD 60.AR907.005 LCD BRACKET W/HINGE - R 33.AR907.006 LCD BRACKET W/HINGE - L 33.AR907.007 LCD COVER ASSY W/MIC W/ANTENNA LCD COVER HOLO 3D W/ 2 ANTENNA 60.AR907.006 CAMERA CN0314-SN30-OV03 SUYIN 57.TPK07.001 CAMERA CNF701721004971L CNY 57.TPK07.002 CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W KC.96001.DTP CPU Intel Core2Dual T9400 PGA 2.
Category Description Part Number Hard Disk HDD TOSHIBA 5400rpm 120GB MK1246GSX Leo BS SATA I LF F/W:LB213J KH.12004.007 HDD WD 5400rpm 120GB WD1200BEVS-22UST0 ML125 SATA LF F/W:01.01A01 KH.12008.019 HDD TOSHIBA 5400rpm 160GB MK1646GSX Leo BS SATA I LF F/W:LB113J KH.16004.002 HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 KH.16008.022 HDD SEAGATE 2.5" 5400rpm 250GB ST9250827AS Corsair SATA LF F/W:3.AAA KH.25001.011 HDD TOSHIBA 2.
Category Description Part Number Keyboard 17KB-FV3 Black Mammoth 105KS Black Traditional Chinese KB.INT00.505 Keyboard 17KB-FV3 Black Mammoth 106KS Black Canadian French KB.INT00.506 Keyboard 17KB-FV3 Black Mammoth 106KS Black Brazilian Portuguese KB.INT00.507 Keyboard 17KB-FV3 Black Mammoth 106KS Black Belgium KB.INT00.508 Keyboard 17KB-FV3 Black Mammoth 105KS Black Arabic/ English KB.INT00.509 Keyboard 17KB-FV3 Black Mammoth 106KS Black Nordic KB.INT00.511 LCD MODULE ASSY17.
Category Description Part Number HDD(160G) ST9160827AS 9DG133-188 STN B/S SEAGATE F/W:3.AAA KH.16001.029 HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00 Bronco-B SATA II LF F/W:C31P KH.16007.016 HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo BS SATA I LF F/W:LB013J KH.25004.001 HDD WD 2.5 IN. 5400rpm 250GB WD2500BEVS-22UST0 ML125 SATA LF F/W:01.01A01 KH.25008.018 HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160 SATA LF F/W:11.01A11 KH.32008.
Appendix A Model Definition and Configuration Aspire 7730/7730G Series Model RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 1ANW XMi AAP India LX.AV 30C.0 02 AS5051AN WXMi LINPUSIL1 UMAC 1*512/80/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N80G B5.4K NSM8 X ABT_ ATH54 13BG N N AS505 1ANW XMi AAP Indonesia LX.AV 30C.0 03 AS5051AN WXMi LINPUSIN1 UMAC 1*512/80/ 6L/5R/ CB_bg_0.
Model 171 RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 1AWX Mi PA USA/ Canada Canadian French LX.AV 30J.00 1 AS5051AW XMi MCECF UMAC 2*512/120/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X ABT_ ATH54 13BG N N AS505 1AWX Mi PA USA/ Canada Canadian French LX.AV 30J.00 2 AS5051AW XMi MCEUS UMAC 2*512/120/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.
Model RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 1AWX Mi AAP Thailand LX.AV 305.00 4 AS5051AW XMi XPHTH2 UMAC 1*512/120/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N120 GB5.4 K NSM8 X ABT_ ATH54 13BG N N AS505 1AWX Mi AAP Vietnam LX.AV 305.00 5 AS5051AW XMi XPHVN1 UMAC 1*512/120/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N120 GB5.
Model 173 RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 1AWX Mi TWN GCTWN LX.AV 305.01 2 AS5051AW XMi XPHTC1 UMAC 1*512/120/ BT/6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N120 GB5.4 K NSM8 X ABT_ ATH54 13BG FOX_ BRM_ 2.0 N AS505 1AWX Mi TWN GCTWN LX.AV 305.01 4 AS5051AW XMi XPHTC1 UMAC 1*512/60/ BT/6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N60G B5.
Model RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 1AWX Mi AAP Thailand LX.AV 30J.01 7 AS5051AW XMi MCETH1 UMAC 1*1G/120/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO1G BII6 N N120 GB5.4 K NSM8 X ABT_ ATH54 13BG N N AS505 1AWX Mi AAP Vietnam LX.AV 30J.01 8 AS5051AW XMi MCEVN1 UMAC 1*1G/120/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO1G BII6 N N120 GB5.
Model 175 RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 2WXM i AAP Thailand LX.AV 30J.00 9 AS5052WX Mi MCETH1 UMAC 1*1G/120/ 6L/5R/ CB_bg_0.3 C_AN ATTL5 0 N14.1 WXGA G SO1G BII6 N N120 GB5.4 K NSM8 X ABT_ ATH54 13BG N N AS505 2WXM i AAP Vietnam LX.AV 30J.01 0 AS5052WX Mi MCEVN1 UMAC 1*1G/120/ 6L/5R/ CB_bg_0.3 C_AN ATTL5 0 N14.1 WXGA G SO1G BII6 N N120 GB5.
Model RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 1ANW XMi AAP Philippines LX.AV 30C.0 11 AS5051AN WXMi LINPUSPH 1 UMAC 1*512/60/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N60G B5.4K NSM8 X ABT_ ATH54 13BG N N AS505 1ANW XMi AAP Malaysia LX.AV 30C.0 12 AS5051AN WXMi LINPUSMA 2 UMAC 1*512/60/ 6L/5R/ CB_bg_0.3 C_AN ATMK 36 N14.1 WXGA G SO512 MBII5 N N60G B5.
177 Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi MCECS5 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K NSM8 X LX.AV 30J.02 4 AS5051AW XMi MCEDK6 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K France LX.AV 30J.02 5 AS5051AW XMi MCEFRF UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 EMEA Germany LX.AV 30J.
Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi MCESI1 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K NSM8 X LX.AV 30J.03 8 AS5051AW XMi MCEPT6 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K Sweden/ Finland LX.AV 30J.02 9 AS5051AW XMi MCESV5 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 EMEA Turkey LX.AV 30J.
179 Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi MCEWFR1 1W UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K NSM8 X LX.AV 305.01 9 AS5051AW XMi XPHBE1 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K Middle East LX.AV 305.03 8 AS5051AW XMi XPHAR1 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 EMEA Eastern Europe LX.AV 305.
Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi XPHNL1 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K NSM8 X LX.AV 305.02 1 AS5051AW XMi XPHFRA UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K Eastern Europe LX.AV 305.02 8 AS5051AW XMi XPHHU6 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 EMEA Spain LX.AV 305.
181 Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi XPHSA1 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K NSM8 X LX.AV 305.02 4 AS5051AW XMi XPHNO1 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 N100 GB5.4 K Russia LX.AV 305.02 5 AS5051AW XMi XPHRU2 UMAC 2*512/100/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII6 SO512 MBII6 EMEA Sweden/ Finland LX.AV 305.
Model RO Country Acer Part no Descriptio n CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) ODD Wirele ss LAN Blueto oth VOIP Phone AS505 2WXM i PA USA/ Canada Canadian French LX.AV 30J.02 1 AS5052WX Mi MCEUS UMAC 2*512/120/ 6L/5R/ CB_bg_0.3 C_AN ATTL5 0 N14.1 WXGA G SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X ABT_ ATH54 13BG N N AS505 2WXM i PA ACLASpanish LX.AV 30J.02 2 AS5052WX Mi MCEES1 UMAC 2*512/120/ 6L/5R/ CB_bg_0.3 C_AN ATTL5 0 N14.1 WXGA G SO512 MBII5 SO512 MBII5 N120 GB5.
183 Acer Part no Wirele ss LAN Blueto oth VOIP Phone NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 BT VoIP PCMC IA N100 GB5.4 K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 BT VoIP PCMC IA N N100 GB5.4 K NSM8 X ABT_ BRM4 318BG N N SO512 MBII6 N N100 GB5.4 K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 BT VoIP PCMC IA N14.1 WXGA SO512 MBII6 N N100 GB5.4 K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 BT VoIP PCMC IA ATTL5 0 N14.1 WXGA G SO512 MBII5 N N120 GB5.4 K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.
Acer Part no Wirele ss LAN Blueto oth VOIP Phone NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 N N60G B5.4K NSM8 X ABT_ BRM4 318BG N N N N60G B5.4K NSM8 X ABT_ BRM4 318BG N N SO512 MBII5 N N60G B5.4K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 N N14.1 WXGA SO512 MBII6 N N100 GB5.4 K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.0 BT VoIP PCMC IA ATMK 36 N14.1 WXGA SO512 MBII6 N N100 GB5.4 K NSM8 X ABT_ BRM4 318BG FOX_ BRM_ 2.
185 Acer Part no DIMM 1 DIMM 2 HDD 1 (GB) N14.1 WXGA G SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K AS5051AW XMi MCEESJ UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 LX.AV 30J.06 4 AS5051AW XMi MCEDEA UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 Germany LX.AV 30J.06 5 AS5051AW XMi MCEDEB UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA EMEA Middle East LX.AV 30J.
Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi MCENL6 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X LX.AV 30J.07 1 AS5051AW XMi MCEIT7 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K Denmark LX.AV 30J.07 4 AS5051AW XMi MCEDK6 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 EMEA France LX.AV 30J.
187 Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi MCEPL7 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X LX.AV 30J.06 7 AS5051AW XMi MCESV5 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K UK LX.AV 30J.08 1 AS5051AW XMi MCEUUK1 1U UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 EMEA UK LX.AV 30J.
Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi XPHDE7 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X LX.AV 305.06 1 AS5051AW XMi XPHAR1 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K Denmark LX.AV 305.04 7 AS5051AW XMi XPHDK1 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 EMEA Belgium LX.AV 305.
189 Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi XPHEL1 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X LX.AV 305.06 9 AS5051AW XMi XPHIS1 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K France LX.AV 305.04 8 AS5051AW XMi XPHFRA UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 EMEA Italy LX.AV 305.
Acer Part no CPU LCD DIMM 1 DIMM 2 HDD 1 (GB) AS5051AW XMi XPHRU2 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K NSM8 X LX.AV 305.05 0 AS5051AW XMi XPHSV1 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 N120 GB5.4 K Slovenia/ Croatia LX.AV 305.06 3 AS5051AW XMi XPHSLO2 UMAC 2*512/120/ 6L/ 5R_bg_0.3 C_AN ATMK 36 N14.1 WXGA SO512 MBII5 SO512 MBII5 EMEA Portugal LX.AV 305.
Model AS505 2NWX Mi 191 RO AAP Country India Acer Part no LX.AV 30C.0 26 Descriptio n AS5052N WXMi LINPUSIL1 UMAC 1*512/80/ BT/6L/5R/ CB_bg_0.3 C_AN CPU LCD ATTL5 0 N14.1 WXGA G DIMM 1 DIMM 2 HDD 1 (GB) ODD SO512 MBII5 N N80G B5.4K NSM8 X Wirele ss LAN Blueto oth VOIP Phone ABT_ ATH54 13BG FOX_ BRM_ 2.
Appendix A 192
Appendix B Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows® XP Home, Windows® XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Microsoft® Windows® Vista Environment Test PCMCIA LAN Card Test Type Device specification LAN Card 16 bit 3Com Megahertz LAN PC Card_589E (Ethernet) LAN Card 32 bit FE575C-3Com 10/100 LAN CardBus-Fast Ethernet Express Card Test Type Device specification 1394 Express Card AboCom Express Card|54 1394B 800Mbs TV Tuner Express Card AVerTV Hybrid Express Slim Card Reader Express Card Maxell Express card|34 5in1 adapter GigaLAN Express Card NETGEAR Gigabit PC card Display Port Test Type External M
Type Printer Device specification • Epson Stylus C65 Printer • HP deskjet 3535 Printer Scanner Canon USB2.0 Scanner Speaker • SCLAR • OZAKI USB 5.1CH-IN-2SPK Digital Sound - US206 • NAZAR GPC-V70 • Logitech Freedom 2.4CordlessJoystick Card Reader • 5 in 1 • HR8-U2M MS/MS-PRO/DUO HDD FUJITSU USB2.0 HDD DVD CD/RW • YAMAHA CD-R/RW Drive • MP5125A DVD+RW/+R • NETAC 1G • Transcend 2G • IBM USB2.0 Device • Panasonic YD-8U10 USB1.0 Device • BELKIN USB1.
Card Reader Test Type MMC Card SD Card Device specification • Transcend 512MB MMC Card • Kingston 1G MMC Card • Sandisk 2.
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
198 Appendix C
Index A display hotkeys AFLASH Utility 39 14 E B EasyTouch Failure Battery Pack 46 Euro BIOS package 22 password control ROM size 21 ROM type 21 vendor 21 Version 21 External Module Disassembly 22 Flowchart 45 F Features 1 22 Fingerprint Reader Failure 27–39 Advanced 30 Boot 37 Exit 38 Navigating 27 BIOS Utility 141 39 FPC Cable 94 Flash Utility FRU (Field Replaceable Unit) List Onboard Device Configuration 33 Power 35 Save and Exit 38 Security 32 System Security 38 159 H 55 Hard Dis
Launch Board LCD Bezel S 77 90 Speaker Module 94 LCD Failure 131 LCD Brackets speakers hotkey LCD Module Disassembly Flowchart 14 System 89 Block Diagram 93 lower covers 49 LCD Panel 4 T Test Compatible Components 193 M Thermal Unit Failure Main Unit Disassembly Flowchart Mainboard Top 62 on indicator 75 Touch Pad Failure 132 141 Troubleshooting 128 Model Definition 170 Modem Board 65 Modem Failure 139 Built-in KB Failure 131 EasyTouch Buttons 140 Fingerprint Reader 141 HDTV Switch 1