Aspire 8735/8735G/8735ZG Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on Aspire 8735/8735G/8735ZG Series service guide.
Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many feature: Platform Intel® Centrino® 2 processor technology, featuring: • • • • • Intel® Core™2 Duo processor T9550 (6 MB L2 cache, 2.66 GHz, 1066 MHz FSB, 35 W), or P7350/ P7450/P7550/P8600/P8700/P8800 (3 MB L2 cache, 2/2.13/2.26/2.40/2.53/2.66 GHz, 1066 MHz FSB, 25 W), supporting Intel®64 architecture (for Aspire 8735/8735G) Intel® Core™2 Duo processor T6400/T6500/T6600 (2 MB L2 cache, 2/2.10/2.
• NVIDIA® GeForce® 9600M GT* Storage subsystem • 2.5" hard disk drive • Optical drive options: •Blu-ray Disc™/DVD-Super Multi double-layer drive* •DVD-Super • Multi double-layer drive* 6-in-1 card reader Special keys and controls • 105/106-key keyboard • Touchpad pointing device Audio • Dolby®-optimized surround sound system with two built-in stereo speakers and one subwoofer* supporting low-frequency effects • True5.
• Line-in jack • Ethernet (RJ-45) port • Modem (RJ-11) port • DC-in jack for AC adapter Environment • Temperature: •Operating: 5 °C to 35 °C •Non-operating: • -20 °C to 65 °C Humidity (non-condensing): •Operating: 20% to 80% •Non-operating: 20% to 80% NOTE: "*" "Only for certain models" NOTE: The specifications listed above are for reference only. The exact configuration of your PC depends on the model purchased.
System Block Diagram 4 Chapter 1
Your Acer Notebook tour After knowing your computer features, let us show you around your new computer. Front View Icon Item Description 1 Acer Crystal Eye webcam Web camera for video communication. 2 Microphone Internal microphone for sound recording. 3 Display screen Also called Liquid-Crystal Display (LCD), displays computer output (Configuration may vary by models). 4 Power button Turns the computer on and off.
Icon Item Description 8 Palmrest Comfortable support area for your hands when you use the computer. 9 Touchpad Touch-sensitive pointing device which functions like a computer mouse. 10 Click buttons (left, center* and right) The left and right buttons function like the left and right mouse buttons. *The center button serves as Acer Bio-Protection fingerprint reader supporting Acer FingerNav 4-way control function (only for certain models).
Left View # Icon 1 Item Description DC-in jack Connects to an AC adapter. HDMI port Supports high definition digital video connections. 3 External display (VGA) port Connects to a display device (e.g., external monitor, LCD projector). 4 Ethernet (RJ-45) port Connects to an Ethernet 10/100/1000-based network. 5 USB 2.0 port Connect to USB 2.0 devices (e.g., USB mouse, USB camera). 6 Line-in jack Accepts audio line-in devices (e.g.
Right View Icon Item Description 1 USB 2.0 port Connects to USB 2.0 devices (e.g., USB mouse, USB camera). 2 Optical drive Internal optical drive; accepts CDs or DVDs. 3 Optical disk access indicator Lights up when the optical drive is active. 4 Optical drive eject button Ejects the optical disk from the drive. 5 Emergency eject hole Ejects the optical drive tray when the computer is turned off.
Bottom View Icon Item Description 1 Battery bay Houses the computer's battery pack. 2 Battery lock Locks the battery in position. 3 Battery release latch Releases the battery for removal. 4 Hard disk baySecondary Houses the computer's hard disk (secured with screws) (only for certain models). 5 Subwoofer Emits low frequency sound output. 6 Hard disk bayMain Houses the computer's hard disk (secured with screws). 7 Memory compartment Houses the computer's main memory.
Indicators The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed. Icon Function Description HDD Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated. Caps Lock Lights up when Caps Lock is activated. Power Indicates the computer's power status. Battery Indicates the computer's battery status. NOTE: 1. Charging: The light shows amber when the battery is charging. 2.
Touchpad basics (with two-click buttons) The following items show you how to use the touchpad with two-click buttons. 1 2 3 • Move your finger across the touchpad (1) to move the cursor. • Press the left (2) and right (3) buttons located beneath the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad is the same as clicking the left button.
Using the Keyboard The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock + When Num Lock is on, the embedded keypad is in numeric mode.
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Keys The computer employs hotkeys or key combinations to access most of the computer’s controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the key before pressing the other key in the hotkey combination. Hotkey 14 Icon Function Description + Hotkey help Displays help on hotkeys. + Acer eSettings Launches Acer eSettings in Acer Empowering Technology.
Special Key (only for certain models) You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol 1. Open a text editor or word processor. 2. Either press < > at the bottom-right of the keyboard, or hold and then press the <5> key at the upper-center of the keyboard. NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information.
Acer Empowering Technology The Empowering Technology toolbar makes it easy for you to access frequently used functions and manage your new Acer system. Activated by pressing the Empowering Key, it provides access to the following utilities: NOTE: The following content is for general reference only. Actual product specifications may vary. • Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home Theater on your system (only for certain models).
Empowering Technology password You must set the Empowering Technology password to use the password protection feature of Acer eRecovery Management to protect your data. To set the Empowering Technology password: 1. Launch Acer eRecovery Management. 2. Click the Restore tab. 3. Click Password settings. The Empowering Technology Password Center dialogue box pops up. 4. Click Create a new password. 5.
Acer eAudio Management (only for certain models) Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home Theater on your system. Select Movie or Game mode to experience the awesome realism of 5.1-channel audio output from the speakers fitted to your system via Dolby Surround sound technology. Music mode lets you enjoy your favorite tunes, in vivid detail. To choose your playback device, click the window.
Acer ePower Management Acer ePower Management features a straightforward user interface for configuring your power management options. To access this utility, select Acer ePower Management from the Empowering Technology toolbar, run the program from the Acer Empowering Technology program group in Start menu, or right-click the Windows power icon in the system tray and select Acer ePower Management.
Battery status 1. The quick menu shows the remaining battery life based on current usage. 2. You can also launch the Acer ePower Management application and refer to the Battery status panel located just below the power plans. 3. Click the Battery tab to view remaining battery life, battery status, and remaining battery life in standby and hibernate modes.
If you set a different password to encrypt a file, but you forgot the encryption password, you can use the Master Password to decrypt the file. NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the Master Password is the only other key capable of decrypting the file.
•Back up factory default to CD/DVD •Back up drivers and applications to CD/DVD •Create user backup •Manage • user backups Restore: •Restore system to factory default •Reinstall •Restore applications/drivers system from user backup •Password settings To use the password protection feature of Acer eRecovery Management to protect your data, you must first set the Empowering Technology password. To set the password, refer to the section "Empowering Technology password".
Acer eSettings Management Acer eSettings Management allows you to inspect hardware specifications, set BIOS passwords and modify boot options. Acer eSettings Management also: • Provides a simple graphical user interface for navigation. • Prints and saves hardware specifications. • Lets you set an asset tag for your system.
Windows Mobility Center The Windows Mobility Center collects key mobile-related system settings in one easy-to-find place, so you can quickly configure your Acer system to fit the situation as you change locations, networks or activities. Settings include display brightness, volume, power plan, wireless networking on/off, external display settings, synchronization status and presentation settings.
Using the System Utilities Acer GridVista (dual-display compatible) NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value.
Hardware Specifications and Configurations Processor Item Specification CPU type ® Core™2 Duo processor T9550 (6 MB L2 cache, 2.66 GHz, Intel 1066 MHz FSB, 35 W), or P7350/P7450/P7550/P8600/P8700/P8800 (3 MB L2 cache, 2/2.13/2.26/2.40/2.53/2.66 GHz, 1066 MHz FSB, 25 W), supporting Intel®64 architecture (for Aspire 8735/8735G) Intel® Core™2 Duo processor T6400/T6500/T6600 (2 MB L2 cache, 2/2.10/2.
System Memory Item Specification Supports DIMM package 200-pin soDIMM Memory module combinations You can install memory modules in any combinations as long as they match the above specifications.
Wireless Module 802.11b/g/n Item Specification Chipset Lan Intel WLAN 533AN_MMWG Shirley Peak/Foxconn Wireless LAN Wireless LAN Ralink RT2700E 1x2 BGN Data throughput 11~54 Mbps, up to 270 Mbps for Draft-N Protocol 802.
Optical Disc Drive Item Specification Vendor & model name TOSHIBA SUPER-MULTI DRIVE DL 8X TS-L633A LF PIONEER SUPER-MULTI DRIVE 8X DVR-TD08RS LF PANASONIC SUPER-MULTI DRIVE DL 8X UJ-870A LF HLDS SUPER-MULTI DRIVE TRAY DL 8X GSA-T50N LF SONY SUPER-MULTI DRIVE DL 8X AD-7560S LF PLDS SUPER-MULTI DRIVE DL 8X DS-8A2S LF Performance Specification With CD Diskette With DVD Diskette Transfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Sustained: Max 10.
Blu-Ray Disc Drive Item Specification Vendor & model name SONY BD COMBO 12.7mm Tray DL 2X BC-5500S LF Performance Specification With CD Disc With DVD Disc With Blu-ray Disc Transfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Sustained: Max 10.08Mbytes/sec Sustained: Max 11 Mbytes/sec Buffer Memory 2MB Interface SATA Applicable disc format Applicable disc format CD: CD-DA, CD-ROM, CD-ROM XA, Photo CD (multi-session), Video CD, CdExtra (CD+), CD-text DVD: DVD-VIDEO, DVD-ROM, DVD-R (3.9GB, 4.
Audio Interface Item Specification Mono or Stereo Stereo Resolution 18 bit stereo full duplex Compatibility HD audio Interface; S/PDIF output for PCM or AC-3 content Sampling rate 1Hz resolution VSR (Variable Sampling Rate) Internal microphone Yes Internal speaker / Quantity Yes/2.
Keyboard Item Specification Keyboard controller NS PC97541V Total number of keypads 105/106-key keyboard Windows logo key Yes Internal & external keyboard work simultaneously Plug USB keyboard to the USB port directly: Yes Battery Item Specification Vendor SONY/Sanyo Battery Type Li-ion Pack capacity 8 cell 4800mAh Number of battery cell 8 Package configuration 4 cells in series, 2 series in parallel LCD 18.
System Power Management ACPI mode 34 Power Management Mech. Off (G3) All devices in the system are turned off completely. Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned off completely. Working (G0/S0) Individual devices such as the CPU and hard disc may be power managed in this state.
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Navigating the BIOS Utility There are five menu options: Information, Main, Security, Boot, and Exit. Follow these instructions: • To choose a menu, use the left and right arrow keys. • To choose an item, use the up and down arrow keys. • To change the value of a parameter, press F5 or F6. • A plus sign (+) indicates the item has sub-items. Press Enter to expand this item. • Press Esc while you are in any of the menu options to go to the Exit menu.
Information The Information screen displays a summary of your computer hardware information.
Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Format/Option System Time Sets the system time. The hours are displayed with 24-hour format. Format: HH:MM:SS (hour:minute:second) System Time System Date Sets the system date. Format MM/DD/YYYY (month/day/ year) System Memory This field reports the memory size of the system.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Option Supervisor Password Is Shows the setting of the Supervisor password Clear or Set User Password Is Shows the setting of the user password. Clear or Set HDD Password Is Shows the setting of the hard disk password. Clear or Set Set Supervisor Password Press Enter to set the supervisor password.
Removing a Password Follow these steps: 1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears: 2. Type the current password in the Enter Current Password field and press e. 3. Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to “Clear”. 4.
If the current password entered does not match the actual current password, the screen will show you the Setup Warning. If the new password and confirm new password strings do not match, the screen will display the following message.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Exit The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the BIOS Setup Utility. Phoenix SecureCore(tm) Setup Utility Security Exit Main Boot Information Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help Esc Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. Use the Flash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Flash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
Remove HDD Password This section provide you with a method of removing HDD password: Remove HDD Password: • If you key in wrong HDD password for three time, “HDD password error code” would display on the screen. See the image below. • If you need to solve HDD password locked problem, you can run HDD_PW.EXE 1. Key in “hdd_pw 15494 0” 2. Select “2” 3. Choose one upper-case string • Chapter 2 Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password.
50 Chapter 2
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.
General Information Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, stable surface. 4. Remove the battery pack.
External Module Disassembly Process External Modules Disassembly Flowchart The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Removing the Battery Pack 54 1. Turn base unit over. 2. Slide the battery lock/unlock latch to the unlock position. 3. Slide the battery release latch to the release position to pop out the battery pack, then remove the battery pack from the main unit.
Removing the SD dummy card 1. Push the SD dummy card all the way in to eject it. 2. Pull it out from the slot.
Removing the ExpressCard dummy card 1. Push the ExpressCard dummy card all the way in to eject it. 2. Pull it out from the slot. Removing the Lower Cover 1. 56 See “Removing the Battery Pack” on page 54.
2. Remove the nine captive screws securing the lower cover. 3. Use a plastic screw driver to carefully pry open the lower cover. 4. Remove the lower cover from the lower case.
Removing the DIMM 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56.. 3. Push out the latches on both sides of the DIMM socket to release the DIMM. 4. Remove the DIMM module. Removing the TV Tuner Board Modules 58 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56.
3. Remove the antenna cable from the board. 4. For Aspire 8730/8730Z Series, remove the one screw (B) securing the board to the system. Step 1 Chapter 3 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.
60 5. For Aspire 8530 Series, release the two latch securing the board to the system by pushing it in the direction of the arrows. 6. Remove the TV tuner board module from the system.
Removing the WLAN Board Modules 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56. 3. “Removing the TV Tuner Board Modules” on page 58. 4. For Aspire 8730/8730Z Series, disconnect the three antenna cables from the WLAN board module. NOTE: There are 3 antenna cables connected to the WLAN board module.
NOTE: There are 2 antenna cables connected to the WLAN board module. The Black antenna cable is connected to the J3 connector and the White antenna cable is connected to the J2 connector. 6. For Aspire 8730/8730Z Series, move the antenna away from the WLAN board and remove the one screw (B) on the WLAN board to release the WLAN board. Step 1 62 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.
7. For Aspire 8530 Series, move the antenna away from the WLAN board and remove the two screws (B) on the WLAN board to release the WLAN board. Step 1~2 8. Size (Quantity) M2 x L4 (2) Color Silver Torque 1.6 kgf-cm Detach the WLAN board from the WLAN socket.
NOTE: When attaching the antenna back to the WLAN board, make sure the cable are arranged properly. Removing the Hard Disk Drive Module 1 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56. 3. Remove the one screw (B) securing the hard disk drive module. Step 1 64 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.
4. Slide the hard disk drive module away from the connector. 5. Lift the hard disk drive module and remove it from the hard disk drive bay. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
6. Remove the four screws (D) securing the hard disk to the bracket and remove the hard disk from the bracket. Step 1~4 Size (Quantity) M3 x L3 (4) Color Silver Torque 3.0 kgf-cm Removing the Hard Disk Drive Module 2 1. 66 See “Removing the Battery Pack” on page 54.
2. Remove the two captive screws securing the hard disk drive cover.
3. Remove the one screw (B) securing the hard disk drive module. Step 1 4. 68 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.6 kgf-cm Slide the hard disk drive module away from the connector.
5. Lift the hard disk drive module and remove it from the hard disk drive bay. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 6. Follow the step 6 of “Removing the Hard Disk Drive Module 1” on page 64 to remove the hard disk from the bracket. Removing the Optical Drive Module 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56. 3. Remove the one screw (B) securing the optical drive module to the system.
70 4. Use a screw driver to push out the locker bracket of the optical drive module. 5. Slowly pull out the odd module from the odd drive bay.
6. Remove the one screw (B) securing the locker bracket and remove the locker bracket from the optical disk drive module. Step 1 Chapter 3 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.
Main Unit Disassembly Process Main Unit Disassembly Flowchart MAIN UNIT DISASSEMBLY MAIN UNIT SCREW X 8 CPU THERMAL MODULE MIDDLE COVER Bx1 Bx2 KEYBOARD POWER BOARD VGA CARD CPU Ax4 LCD MODULE A x 16 UPPER CASE Bx2 MODEM CARD Bx2 E-KEY BOARD Bx2 FINGERPRINT MODULE TOUCHPAD MODULE Bx1 MAIN BOARD Bx3 Bx2 SUBWOOFER SPEAKER MODULE Bx1 USB MODULE Screw List 72 Item Screw Color Part No. A M2 x L4 Black 86.00E34.738 B M2 x L4 Silver 86.9A552.
Removing the Middle Cover 1. See “Removing the Battery Pack” on page 54. 2. Use a plastic screw driver to pry loose the side of the middle cover. 3. Carefully pry loose the middle cover from the latches securing it and remove the middle cover.
Removing the Keyboard 74 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Middle Cover” on page 73. 3. Push up on the four latches securing the keyboard to the upper case. 4. Carefully pry loose the keyboard and turn it over on the touchpad area.
5. Disconnect the keyboard cable from the main board to remove the keyboard. Removing the Power Board 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Middle Cover” on page 73.
3. Remove the one screw (B) securing the power board to the upper case. Step 1 4. 76 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.6 kgf-cm Release the power board from the latch and turn it over.
5. Disconnect the power board cable from PWCN1 connector on the system to remove it.
Removing the Heatsink Module NOTE: There are two version of heatsink module. For this section, we are going to use the discrete model. The UMA version looks like the picture below: 78 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56. 3. Disconnect the heatsink connector from the main board.
4. Remove the eight screws securing the heatsink module in the order shown. NOTE: The green VGA board in Aspire 8730/8730Z Series is made by NVdia, while the red VGA board in Aspire 8530 Series is made by ATI. 5. Carefully lift up the heatsink module.
Removing the CPU NOTE: Aspire 8730/8730Z Series uses the Intel® processor, while Aspire 8530 Series uses the AMD® processor. But the process in removing the CPU are the same for all the models. 80 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56. 3. See “Removing the Heatsink Module” on page 78. 4. Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU.
5. Lift up carefully to remove the CPU. NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown.
Removing the Discrete Board Module (For Discrete Models Only) NOTE: Aspire 8730/8730Z Series uses the NVdia board, while Aspire 8530 Series uses the ATI board. The process for removing the board are the same for models with discrete board module. 82 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the Lower Cover” on page 56. 3. See “Removing the Heatsink Module” on page 78. 4. Remove the two screws (B) securing the discrete board to the system.
Step 1~2 5. Size (Quantity) M2 x L4 (2) Color Silver Torque 1.6 kgf-cm Remove the discrete board module from the system.
Removing the LCD Module 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the TV Tuner Board Modules” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the Middle Cover” on page 73. 8. See “Removing the Keyboard” on page 74. 9.
10. Turn over the system and remove the mylar covering the LCD cable connector. 11. Disconnect the LCD cable connector from the main board.
12. Carefully pull out the wireless antenna cables from the hole and release the cables from the latches. 13. Disconnect the microphone cable from MIC1 on the system and release it from the latches.
14. Remove the two screws (A) from the left and right hinge of the LCD module. Step 1~2 Size (Quantity) M2.5 x L8 (2) Color Black Torque 3.0 kgf-cm 15. Carefully remove the LCD module from the base unit. NOTE: When connecting the cable back to the unit, please note that the cable should be routed well. Separating the Upper Case from the Lower Case 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3.
10. See “Removing the Hard Disk Drive Module 2” on page 66. 11. See “Removing the Middle Cover” on page 73. 12. See “Removing the Keyboard” on page 74. 13. See “Removing the Heatsink Module” on page 78. 14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. Disconnect the touchpad cable from the TPDA1 connector on the main board.
17. Disconnect the fingerprint cable from FP2 on the main board. 18. Disconnect the E-key cable from EKCN1 on the main board.
19. Disconnect the Media console cable from LEDB1 on the main board.
20. Disconnect the power cable from DC1 connector on the main board. 21. Disconnect the speaker cable from REAR1 connector on the main board.
22. Remove the thirteen screws (A) from the bottom panel. Step 1~13 Size (Quantity) M2.5 x L8 (13) Color Black Torque 3.0 kgf-cm 23. Turn the unit over and remove the three screws (A) from the top panel. Step 1~3 92 Size (Quantity) M2.5 x L8 (3) Color Black Torque 3.
24. Gently remove the upper case from the lower case. CAUTION: Remember to release the power cable from the hole on the upper case before removing the upper case from the system. Removing the E-Key Board 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58.
12. See “Removing the Keyboard” on page 74. 13. See “Removing the Heatsink Module” on page 78. 14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. See “Separating the Upper Case from the Lower Case” on page 87. 17. Remove the two screws (B) securing the board. Step 1~2 Size (Quantity) M2 x L4 (2) Color Silver Torque 1.6 kgf-cm 18. Disconnect the cable from the board and remove the board from the upper case.
Removing the Fingerprint Board 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the TV Tuner Board Modules” on page 58. 8. See “Removing the Hard Disk Drive Module 1” on page 64. 9.
14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. See “Separating the Upper Case from the Lower Case” on page 87. 17. Remove the two screws (B) securing the board. Step 1~2 Size (Quantity) M2 x L4 (2) Color Silver Torque 1.6 kgf-cm 18. Disconnect the cable from the board and remove the board from the upper case.
Removing the Touchpad Board 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the TV Tuner Board Modules” on page 58. 8. See “Removing the Hard Disk Drive Module 1” on page 64. 9.
14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. See “Separating the Upper Case from the Lower Case” on page 87. 17. Disconnect the touchpad cable from the touchpad board.
18. Remove the mylar tape from the touchpad board. 19. Carefully pry loose and remove the touchpad board. WARNING:The touchpad board is glued to the upper case, only remove the touchpad board if it is defective.
Removing the Modem Board 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the TV Tuner Board Modules” on page 58. 8. See “Removing the Hard Disk Drive Module 1” on page 64. 9. See “Removing the Hard Disk Drive Module 2” on page 66.
18. Remove the two screw (B) securing the modem card. Step 1~2 Size (Quantity) M2 x L4 (2) Color Silver Torque 1.6 kgf-cm 19. Lift the modem board to remove it from the main board. Removing the Main Board 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6.
11. See “Removing the Middle Cover” on page 73. 12. See “Removing the Keyboard” on page 74. 13. See “Removing the Heatsink Module” on page 78. 14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. See “Separating the Upper Case from the Lower Case” on page 87. 17. See “Removing the Modem Board” on page 100. 18. Disconnect the USB cable from the USBCN1 connector on the main board. 19. Disconnect the subwoofer cable from FRONT1 connector on the main board.
20. Remove the one screw (B) securing the main board in place. Step 1 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.6 kgf-cm 21. Carefully remove the main board. Removing the Speaker Module 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7.
11. See “Removing the Middle Cover” on page 73. 12. See “Removing the Keyboard” on page 74. 13. See “Removing the Heatsink Module” on page 78. 14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. See “Separating the Upper Case from the Lower Case” on page 87. 17. See “Removing the Modem Board” on page 100. 18. See “Removing the Main Board” on page 101. 19. Remove the tape securing speaker cable. 20. Remove the three screws (B) securing the speaker module.
21. Remove the speaker module from the upper case. Removing the Subwoofer 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the TV Tuner Board Modules” on page 58. 8. See “Removing the Hard Disk Drive Module 1” on page 64. 9.
19. Remove the two screws (B) securing the subwoofer to the lower case. Step 1~2 Size (Quantity) M2 x L4 (2) Color Silver Torque 1.6 kgf-cm 20. Remove the subwoofer from the lower case. Removing the USB Board Module 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the DIMM” on page 58. 6.
11. See “Removing the Middle Cover” on page 73. 12. See “Removing the Keyboard” on page 74. 13. See “Removing the Heatsink Module” on page 78. 14. See “Removing the CPU” on page 80. 15. See “Removing the LCD Module” on page 84. 16. See “Separating the Upper Case from the Lower Case” on page 87. 17. See “Removing the Modem Board” on page 100. 18. See “Removing the Main Board” on page 101. 19. Disconnect the cable from the USB board module. 20.
21. Remove the USB board module from the lower case.
LCD Module Disassembly Process LCD Module Disassembly Flowchart LCD MODULE DISASSEMBLY LCD MODULE Cx6 LCD BEZEL Cx5 LCD ASSEMBLY LCD BACK PANEL Ex3 LCD FPC CABLE LEFT LCD BRACKET Ex3 RIGHT LCD BRACKET ANTENNAS VGA CAMERA Screw List Item Screw Color Part No. C M2.5 x L6 Black 86.00E33.736 E M2 x L3 Silver 86.9A522.
Removing the LCD Bezel 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the TV Tuner Board Modules” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the Middle Cover” on page 73. 8. See “Removing the Keyboard” on page 74. 9. See “Removing the LCD Module” on page 84. 10.
12. Carefully pry open the LCD bezel and place the bezel on top of the LCD panel. Removing the LCD panel with the Brackets 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the TV Tuner Board Modules” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the Middle Cover” on page 73. 8.
11. Disconnect the cable from the web camera. 12. Remove the five screws (C) securing the LCD module. Step 1~5 112 Size (Quantity) M2.5 x L6 (5) Color Black Torque 3.
13. Remove the LCD with the brackets from the back cover. Removing the Inverter Board and FPC Cable 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the TV Tuner Board Modules” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the Middle Cover” on page 73. 8.
13. Detach any adhesive tapes and any cable that is glued to the LCD panel.
14. Disconnect the FPC cable from the LCD panel.
Removing the LCD Brackets 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the TV Tuner Board Modules” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the Middle Cover” on page 73. 8. See “Removing the Keyboard” on page 74. 9. See “Removing the LCD Module” on page 84. 10.
11. See “Removing the Inverter Board and FPC Cable” on page 113. 12. See “Removing the LCD panel with the Brackets” on page 111. 13. Release the antenna cables from the aluminium tapes. 14. Remove the left and right antenna cables together with the tapes holding them in place.
NOTE: There is no need to remove the antenna unless you really need to replace it. Removing the Web Camera 1. See “Removing the Battery Pack” on page 54. 2. See “Removing the SD dummy card” on page 55. 3. See “Removing the ExpressCard dummy card” on page 56. 4. See “Removing the Lower Cover” on page 56. 5. See “Removing the TV Tuner Board Modules” on page 58. 6. See “Removing the TV Tuner Board Modules” on page 58. 7. See “Removing the Middle Cover” on page 73. 8.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. Boot from the diagnostics diskette and start the diagnostics program. 2.
q External keyboard If any of these devices do not work, reconnect the cable connector and repeat the failing operation. Memory Check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the diagnostic program (please refer to main board. 2. Go to the diagnostic memory in the test items. 3. Press F2 in the test items. 4. Follow the instructions in the message window.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: q Replace the System board. q If the problem is not corrected, see “Undetermined Problems” on page 139. q If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes Error Messages 006 Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 System disabled. Incorrect password is specified.
Error Message List Error Messages 126 FRU/Action in Sequence System timer error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Real time clock error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages FRU/Action in Sequence No beep, power-on indicator turns off and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 121.. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 121..
Phoenix BIOS Beep Codes Code Beeps Verify Real Mode 03h Disable Non-Maskable Interrupt (NMI) 04h Get CPU type 06h Initialize system hardware 08h Initialize chipset with initial POST values 09h Set IN POST flag 0Ah Initialize CPU registers 0Bh Enable CPU cache 0Ch Initialize caches to initial POST values 0Eh Initialize I/O component 0Fh Initialize the local bus IDE 10h Initialize Power Management 11h Load alternate registers with initial POST values 12h Restore CPU control word du
Code Beeps POST Routine Description 3Ch Advanced configuration of chipset registers 3Dh Load alternate registers with CMOS values 42h Initialize interrupt vectors 45h POST device initialization 46h 2-1-2-3 Check ROM copyright notice 48h Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h In
Code POST Routine Description Detect and install external RS232 ports 83h Configure non-MCD IDE controllers 84h Detect and install external parallel ports 85h Initialize PC-compatible PnP ISA devices 86h Re-initialize onboard I/O ports 87h Configure Motherboard Configurable Devices (optional) 88h Initialize BIOS Area 89h Enable Non-Maskable Interrupts (NMIs) 8Ah Initialize Extended BIOS Data Area 8Bh Test and initialize PS/2 mouse 8Ch Initialize floppy controller 8Fh Determine number
Code Beeps POST Routine Description B9h Prepare Boot BAh Initialize DMI parameters BBh Initialize PnP Option ROMs BCh Clear parity checkers BDh Display MultiBoot menu BEh Clear screen (optional) BFh Check virus and backup reminders C0h Try to boot with INT 19 C1h Initialize POST Error Manager (PEM) C2h Initialize error logging C3h Initialize error display function C4h Initialize system error handler C5h PnPnd dual CMOS (optional) C6h Initialize notebook docking (optional) C7h
Code 132 Beeps F5h Boot to Mini DOS F6h Clear Huge Segment F7h Boot to Full DOS Chapter 4
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error Action in Sequence LCD backlight doesn't work LCD is too dark LCD brightness cannot be adjusted LCD contrast cannot be adjusted Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. Reconnect the LCD connectors. Keyboard (if contrast and brightness function key doesn't work).
Power-Related Symptoms Symptom / Error Action in Sequence The system doesn’t power-off. Power source (battery pack and power adapter). See “Power System Check” on page 121. Hold and press the power switch for more than 4 seconds. System board Battery can’t be charged See “Check the Battery Pack” on page 123. Battery pack System board PCMCIA-Related Symptoms Symptom / Error Action in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly System board PCMCIA slot pin is damaged.
Power Management-Related Symptoms Symptom / Error Action in Sequence The system doesn't resume from hibernation mode. See “Save to Disk (S4)” on page 34. Hard disk connection board Hard disk drive System board The system doesn't resume from standby mode after opening the LCD. See “Save to Disk (S4)” on page 34. LCD cover switch System board Battery fuel gauge in Windows doesn’t go higher than 90%. Remove battery pack and let it cool for 2 hours.
Modem-Related Symptoms Symptom / Error Internal modem does not work correctly. Action in Sequence Modem phone port modem combo board System board NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined Problems” on page 139.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 121.
Chapter 4 139
140 Chapter 4
Chapter 5 Jumper and Connector Locations Motherboard Chapter 5 139
140 Chapter 5
Clearing Password Check and BIOS Recovery This section provide you the standard operating procedures of clearing password and BIOS recovery for Aspire 5730Z/5330 Series. Aspire 5730Z/5330 Series provide one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.
try again. NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).
BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. BIOS Recovery Hotkey: The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered on during BIOS POST.
144 Chapter 5
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of 8735/8735G/8735ZG Series. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Aspire 8735/8735G/8735ZG Series Exploded Diagram 146 Chapter 6
Aspire 8735G FRU List CATEGORY PART NAME ACER PART NO. ADAPTER ADAPTER 90W 19V 3PIN DELTA ADP-90CD DB A LV5 LED LF BLUE AP.09001.027 AP.09001.027 ADPAPTER 90W 19V 3PIN LITEON PA-190034AR LV5 LED LF BLUE AP.09003.021 AP.09003.021 ADPAPTER 90W 19V 3PIN HIPRO HP-A0904A3 B1LF LV5 LED LF BLUE AP.0900A.005 AP.0900A.005 BATTERY SANYO AS-2007B LI-ION 4S2P SANYO 8 CELL 4800MAH MAIN COMMON BT.00803.024 BATTERY SONY AS-2007B LI-ION 4S2P SONY 8 CELL 4800MAH MAIN COMMON BT.00804.
CATEGORY PART NAME ACER PART NO. POWER CORD 10A 250V 3PIN BK SOUTH AFRICA 27.01518.571 POWER CORD 16A 250V SOUTH AFRICA BK 27.01518.681 POWER CORD 2.5A 250V AUSTRALIA 27.01518.621 POWER CORD ACA / ACNZ 27.03218.021 POWER CORD 7.5A 250V 3P AUSTRALIA BK 27.03218.051 POWER CORD 2.5A 250V SOUTH AFRICA BK (INDIA) 27.01518.631 POWER CORD 10A 250V SOUTH AFRICA BK (INDIA) 27.01518.721 POWER CORD 7A 125V 2PIN JAPAN 27.01518.551 POWER CORD 7A 125V 2PIN JAPAN BK 27.01518.
CATEGORY PART NAME ACER PART NO. CPU INTEL CORE2DUAL P7450 2.13G 3M 1066 TJ NOVT KC.74501.DPP CPU INTEL CORE2DUAL P7450 2.13G 3M R-0 TJ KC.74501.DPR CPU INTEL CORE2DUAL P7550 PGA 2.26G 3M 1066 R-0 KC.75501.DPP CPU INTEL CORE2DUAL P8600 2.4G 3M 1066 25W R-0 KC.86R01.DPP CPU INTEL CORE2DUAL P8700 2.53G 3M 1066 25W R-0 KC.87R01.DPP CPU INTEL CORE2DUAL P8800 PGA 2.66G 3M 1066 25W R-0 KC.88R01.DPP CPU INTEL CORE2DUAL PENRYN T9550 2.66G 6M 1066 35W E-0 KC.95501.
CATEGORY PART NAME ACER PART NO. HDD 250GB 5400RPM SATA TOSHIBA LIBRA-BS MK2555GSX F/W:FG000J 5.4K KH.25004.003 HDD 250GB 5400RPM SATA HGST HTS545025B9A300 PANTHER-B LF KH.25007.015 HDD 250GB 5400RPM SATA WD WD2500BEVT22ZCT0 F/W:11.01A11 KH.25008.021 HDD 320GB 5400RPM SATA SEAGATE WYATT ST9320325AS FW:0001SDM1 KH.32001.017 HDD TOSHIBA 2.5" 5400RPM 320GB MK3263GSX SATA 8MB 68P LF F/W:FG020J KH.32004.003 HDD 320GB 5400RPM SATA HGST HTS545032B9A300 PANTHER B LF KH.32007.
CATEGORY PART NAME ACER PART NO. KEYBOARD 17KB-FV5 BLACK 105KS DARFON NSK-AFF0K KOREA KB.I1700.019 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0E ITALIAN KB.I1700.021 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0Q HUNGARIAN KB.I1700.024 KEYBOARD 17KB-FV5 BLACK 105KS DARFON NSK-AFF0L GREEK KB.I1700.025 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0G GERMAN KB.I1700.026 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0F FRENCH KB.I1700.027 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0D DANISH KB.
CATEGORY PART NAME ACER PART NO. LCD 18.4" WUXGA28L GLARE CMO N184H4-L04 LF 220NIT 8MS 500:1 LK.1840D.001 LCD MODULE 18.4" WXGA+G8 GLARE IMR BLUE/BLACK W/0.3M CAMERA&ANTENNA*2 FOR SINGLE LAMP 6M.PHF01.004 INVERTER BOARD 18" AMPOWER T62I262.00 BIGBEAR 19.PHF01.002 INVERTER BOARD 18" DARFON VK.21189.803 19.PHF01.003 LCD BRACKET RIGHT W/HINGE 33.AYP01.003 LCD BRACKET LEFT W/HINGE 33.AYP01.004 LCD/CAMERA CABLE FOR SINGLE LAMP 50.PHF01.002 CAMERA 0.3M SUYIN CN0314-SN30-OV03-5 57.N4401.
CATEGORY PART NAME SODIMM 2GB DDRIII 1066MHZ HYNIX HMT125S6BFR8C-G7 N0 LF 128*8 0.055UM ACER PART NO. KN.2GB0G.014 MISCELLANEOUS NAME PLATE ASPIRE 8735 40.PHF01.001 LCD SCREW RUBBER OF UPPER 47.AYP01.002 LCD SCREW RUBBER OF LOWER 47.AYP01.003 SCREW SCREW 86.00A02.140 SCRW M2*L6 ZN ROHS 86.00D50.620 SCRW M2XL4.2 BZN 86.00E10.524 SCREW M2.5*L6 NYLOK CR3+ 86.00E33.736 SCREW M2.5*L8 NYLOK CR3+ 86.00E34.738 SCREW M3 X 3 #1 NI NYLON 86.00E78.643 SCREW 86.9A522.3R0 SCREW M2*4 WAFER NI 86.
CATEGORY PART NAME ACER PART NO. WIRELESS LAN BOARD FOXCONN ATHEROS XB63 MINICARD B/G NI.23600.046 BLUETOOTH BOARD FOXCONN BRM 2046 BT2.1 T60H928.33 F/W:861 BH.21100.004 CABLE POWER CORD 10A 125V US 27.T30V1.001 POWER CORD 10A 125V 3PIN US BK 27.01518.641 POWER CORD 250V 3PIN EUR BK 27.T30V1.004 POWER CABLE 16A 250V 3PIN EUR BK 27.01518.731 POWER CORD 3A 250V 3PIN UK 27.01518.541 POWER CORD 5A 250V 3PIN UK BK 27.03118.001 POWER CORD 10A 3PIN BK DENMARK 27.01518.
CATEGORY PART NAME LOWER CASE W/MODEM&DC-IN CABLE&SPEAKER W/O TV HOLE ACER PART NO. 60.PHF01.001 SPEAKER SPEAKER PACK RIGHT & LEFT 23.PHF01.001 SPEAKER SUBWOOFER 23.PHF01.002 UPPER CASE W/E-KEY&MEDIA CONSOLE&TOUCH PAD&FINGER PRINT CABLE W/O FINGER PRINT HOLE 60.PHF01.002 MIDDLE COVER 42.PHF01.001 CPU INTEL PENTIUM DUAL-CORE T4200 PGA 2.0G 1M 800 35W R-0 KC.42001.DTP CPU INTEL PENTIUM DUAL-CORE T4300 PGA 2.1G 1M 800 R-0 KC.43001.DTP CPU INTEL PENTIUM DUAL-CORE T4400 2.2G 1M 800 KC.44001.
CATEGORY PART NAME ACER PART NO. HDD 160GB 5400RPM 2.5" SATA WD WD1600BEVT-22ZCT0 FW:11.01A11 KH.16008.022 HDD 2.5" 5400RPM 250GB SEAGATE ST9250315AS WYATT SATA LF F/W:0001SDM1 KH.25001.016 HDD 250GB 5400RPM SATA TOSHIBA LIBRA-BS MK2555GSX F/W:FG000J 5.4K KH.25004.003 HDD 250GB 5400RPM SATA HGST HTS545025B9A300 PANTHER-B LF KH.25007.015 HDD 250GB 5400RPM SATA WD WD2500BEVT22ZCT0 F/W:11.01A11 KH.25008.021 HDD 320GB 5400RPM SATA SEAGATE WYATT ST9320325AS FW:0001SDM1 KH.32001.017 HDD TOSHIBA 2.
CATEGORY PART NAME ACER PART NO. KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF05 POLISH KB.I1700.016 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0N NORWEGIAN KB.I1700.017 KEYBOARD 17KB-FV5 BLACK 105KS DARFON NSK-AFF0K KOREA KB.I1700.019 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0E ITALIAN KB.I1700.021 KEYBOARD 17KB-FV5 BLACK 106KS DARFON NSK-AFF0Q HUNGARIAN KB.I1700.024 KEYBOARD 17KB-FV5 BLACK 105KS DARFON NSK-AFF0L GREEK KB.I1700.
CATEGORY PART NAME ACER PART NO. CAMERA 0.3M CHICONY CNF701721004973L 57.W9401.001 LCD BEZEL W/LOGO&CAMERA HOLE 60.AYP01.004 LCD COVER 18.4" BLUE IMR W/MICROPHONE & ANTENNA*2 60.PHF01.004 LCD 18.4" WUXGA28L GLARE CMO N184H4-L04 LF 220NIT 8MS 500:1 LK.1840D.001 LCD MODULE 18.4" WXGA+G8 GLARE IMR BLUE/BLACK W/0.3M CAMERA&ANTENNA*2 FOR SINGLE LAMP 6M.PHF01.004 INVERTER BOARD 18" AMPOWER T62I262.00 BIGBEAR 19.PHF01.002 INVERTER BOARD 18" DARFON VK.21189.803 19.PHF01.
CATEGORY PART NAME ACER PART NO. SODIMM 2GB DDRIII 1066MHZ ELPIDA EBJ21UE8BBS0-AE-F KN.2GB09.004 MEMORY ELPIDA SO-DIMM DDRIII 1066 2GB EBJ21UE8BDS0-AE-F LF 128*8 0.065UM KN.2GB09.006 SODIMM 2GB DDRIII 1066MHZ SAMSUNG M471B5673EH1-CF8 KN.2GB0B.012 SODIMM 2GB DDRIII 1066MHZ HYNIX HMT125S6BFR8C-G7 N0 LF 128*8 0.055UM KN.2GB0G.014 MISCELLANEOUS NAME PLATE ASPIRE 8735Z 40.PHH01.001 LCD SCREW RUBBER OF UPPER 47.AYP01.002 LCD SCREW RUBBER OF LOWER 47.AYP01.003 SCREW Chapter 6 SCREW 86.00A02.
Appendix A Model Definition and Configuration Aspire 8735/8735G/8735ZG Series Please double click the icon below to open the complete list.
Appendix B Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows® XP Home, Windows® XP Pro environment, Windows® Vista. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Microsoft® Windows® Vista Environment Test Item Specification CRT Port Test CRT Monitor Acer 211c 21”, ViewSonic G220F, ViewSonic PF790 19” LCD Monitor Acer FP751 17” TFT LCD, Acer AL1521, Acer AL1721, ViewSonic VD201b, Westinghouse W37G, HP LP2065, HP S9500 Projector Dell 3300MP USB Port Test USB Keyboard/Mouse Microsoft Natural Keyboard Pro Dell USB Keyboard Logicool USB Mouse (OWCM-USB) Logitech USB Wheel Mouse Logitech First Wheel Mouse Dell by Logitech Dell Internet Navigator Keyboard Dell Sma
Item Specification PCMCIA Test LAN/Modem Card TDK CardBus Ethernet 10/100 32-Bit CBE-10/100BTX Storage Card Hitachi Microdrive 4G 1394 Card Buffalo 1394 Interface Cardbus (IFC-ILCB/DV) USB2.0 Card IBM EtherJet CardBus Adapter 10/100 Wireless Lan Card Cisco Wireless LAN Card 802.11a (Not recommended for wireless ready model) NETGEAR Wireless LAN card 802.
158 Appendix B
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
160 Appendix C