Owner's Manual

ManualsBrandsASRock ManualsDesktopsASRock IMB-142 Series

Motherboard Layout

1 JCF Power Connector (JCF PWR1) 16 Clear CMOS Jumper (CLRCMOS1)

2 ATX 12V Power Connector (ATX12V1) 17 Chassis Speaker Header

3 CPU Fan Connector (CPU_FAN1) (SPEAKER 1, White)

4 Chassis Fan Connector (CHA_FAN2) 18 JPS Connector (JPS2)

5 Chassis Fan Connector (CHA_FAN1) 19 USB 2.0 Header (USB2_3, Blue)

6 CPU Heatsink 20 USB 2.0 Header (USB4_5, Blue)

7 2 x DDR3 DIMM Slots 21 Chipset Heatsink

8 16Mb Flash 22 PCI Slot (PCI1)

9 SMBUS Connector (SMBUS1) 23 JGP IO Connector (JGP IO1)

10 SATA2 Connector (SATAII_1, Blue) 24 COM Port Header (COM1)

11 SATA2 Connector (SATAII_2, Red) 25 COM Port Header (COM2)

12 USB 2.0 Header (USB6_7, Blue) 26 PCI Express x1 Slot (PCIE1, White)

13 JPWR Connector (JPWR1) 27 LVDS Connector (LVDS1)

14 SATA Power Connector (SATAPWR1) 28 CON1

15 System Panel Header (PANEL1, White) 29 VGA Header (VGA1)

17.0cm (6.7 in)

HDMI1

DVI2

Top:

Line In

Center:

Line Out

Bottom:

Mic In

USB 2.0

T: USB0

B: USB1

LAN2

LAN1

JCF PWR1

VGA1

Super

COM2

COM1

AUDIO

CODEC

PCI1

JGP IO1

JPS2

SPEAKER1

CLRCMOS1

SATAPWR1

USB2_3

USB4_5

USB6_7

PANE L 1

HDLED RESET

PLED PWRBTN

JPWR1

SATAII_1

SATAII_2

CMOS

Battery

16Mb

BIOS

FSB800

DDR3_A1

DDR3_B1

CPU_FAN1 CHA_FAN2 CHA_FAN1

PCIE1

CON1

SMBUS1

RoHS

Designed in Taipei

IMB-142

ErP/EuP Ready

LVDS 1

Summary of content (6 pages)

PAGE 1
Motherboard Layout 3 2 1 6 5 4 7 17.0cm (6.7 in) JCF PWR1 ErP/EuP Ready 1 HDMI1 CPU_FAN1 CHA_FAN1 1 29 28 27 CHA_FAN2 DVI2 PCIE1 17.0cm (6.7 in) CON1 1 DDR3_B1 DDR3_A1FSB800 VGA1 LVDS1 26 USB 2.
PAGE 2
Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins. Jumper Clear CMOS Jumper Setting Description (CLRCMOS1) (see p.1, No. 16) Default Clear CMOS Note: CLRCMOS1 allows you to clear the data in CMOS.
PAGE 3
Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! SATAII Connectors (SATAII_1: see p.1, No. 10) (SATAII_2: see p.1, No. 11) SATAII_1 USB 2.0 Headers SATAII_2 USB_PWR P-3 P+3 GND DUMMY (9-pin USB2_3) (see p.1 No.
PAGE 4
RESET (Reset Switch): Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart. PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
PAGE 5
ATX 12V Power Connector Please connect an ATX 12V (4-pin ATX12V1) power supply to this connector. (see p.1 No. 2) Serial port Headers Each COM1 header supports a serial port module. (9-pin COM1) (see p.1 No. 24) (9-pin COM2) (see p.1 No. 25) JCF Power Connector (3-pin JCF PWR1) (see p.1 No. 1) 1 +5V CF Socket Power (Con1) +3V D-SUB VGA Connector (15-pin VGA1) Dsub DDCCLK Dsub HSYNC Dsub VSYNC N/A Dsub DDC DATA (see p.1 No.
PAGE 6
SMBUS Connector 1 (2-pin SMBUS1) SMBUS DATA SMBUS CLK (see p.1 No.