User guide

OPERATION MANUAL
– 4 –– 3 –– 2 –– 1 –
– 5 – – 7 –
ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH
ENGLISH ENGLISH ENGLISH ENGLISH
– 6 –
ENGLISH ENGLISH
– 8 –
ENGLISH ENGLISH
The product is used to display the time in hours
and minutes. The display takes place by means of
LEDs. The product is approved only for operation
in dry rooms. Use other than that described above
will lead to damage to the product and also involves
additional risks.
SAFETY INSTRUCTIONS AND DANGER
WARNINGS
The guarantee will lapse if damage is occurred as
a result of non-compliance with these operating in-
structions! The guarantee will lapse in such cases.
For safety and licensing (CE) reasons, unauthor-
ized conversion and/or modifications to the product
are not permitted.
The
device may not be exposed to extreme tem-
peratures (<0°C/>+50°C), strong vibration or heavy
mechanical stress. There is risk of damage!
The plug-in unit is constructed according to
protection class II.
The product is approved only for operation in
dry rooms.
Never pour any liquids on the appliance. You run
the risks of causing a fi
re or fatal electric shock! If
liquid or any other object penetrates the appliance,
disconnect the main plug immediately and contact
a specialist.
Only a specialist may replace a damaged plug-in
or damaged connection cable. There is risk of fatal
electric shock!
Only a 230V/50Hz socket may be used as
the source of power for the plug-in power unit.
Never try to operate the appliance on any other
voltage.
Always unplug the plug-in power unit out of the
socket by the casing, never by the cable!
The plug-in power unit may never be plugged in
or taken out with wet hands.
Always unplug the plug-in power unit from the
socket!
– before cleaning the appliance
– during thunderstorms
– if you will not be using the appliance for a long
period.
The product is not a toy and must be kept out of
reach of children. Children cannot estimate the risks
which can arise because of incorrect handling of
electrical appliances.
Do not leave the packing material lying around
carelessly. Plastic foil and/or bags and polystyrene
parts ect. can become dangerous toys in the hands
of children.
Never switch on the device immediately after it
have been taken from a cold to a warm room. The
condensate can destroy the device under certain
circumstances. Let the device to reach room
temperature before switching it on. Wait until the
condensate water vaporize.
Only use the supplied plug-in power unit for the
power supply of the clock.
The unit may not be opened.
The device is not suitable for commercial use.
FEATURES
CONNECTION OF CLOCK
Plug the plug-in power unit low voltage plug (small
plug on the cable) into the low-voltage jack, which
is located on the side of the clock. Then plug the
plug-in power unit into a 230V/50Hz socket. The
display of the clock will appear.
Always withdraw the plug-in power unit fi
rst from
the socket before you take the low-voltage plug
out of the clock.
ADJUSTING CLOCK
The adjusting buttons are located on the back
side of the clock.
Adjusting the hours:
• Hold down the key [TIME] (the display fl
ashes).
Now
press the button [HOUR] as well. Hold down
both keys until the desired hour is set.
Adjusting the minutes:
• Hold down the key [TIME] (the display fl
ashes).
N
ow press the button [MIN] as well. Hold down both
keys until the desired minute is set.
USE AS A WALL CLOCK
When setting up the device, make sure that the
base is stable. When hanging up the device, make
sure that the attachment is secure. If the appliance
falls, it can injure people or break.
Wall clock:
Pay attention when mounting that no power, gas
or water pipes are damaged by mistake! Danger
of death!
When mounting on the wall, use screws and
dowels which are suitable for the composition of
the wall.
Do not place the clock near the sources of dis-
turbance such as PC, mobile phones etc. Always
keep a distance at least 50 cm from such sources
of disturbance.
Use the two attachment holes on the back of the
clock as a drilling model. Drill two corresponding
holes in the wall and insert the dowels (if they are
necessary). For the clock to be attached correctly,
the screws should have a distance of approximately
4 mm between the lower side of the screw head and
the wall. Hang up the clock on the two screws.
MAINTAINANCE AND DISPOSAL
The outside of the device should be cleaned with
a soft, slightly damp cloth or a dry brush. Do not
use any aggressive cleaning liquids or chemical
solutions, as they may damage the device.
When the device has become unusable, dispose
it in accordance with the current statutory regula-
tions.
Note: Due to electromagnetic discharge or dis-
turbances clock may not function correctly. For
example, the display may not change. And there
will be «RESET» on it. To eliminate the error with-
draw the plug-in power unit from the socket. Wait
around 10 minutes and then plug it into the socket
again. The clock will be reset, and you’ll have to
set the time again.
After withdrawing the plug-in power unit, the time
will be stored for about 10 seconds after that the
clock has to be set again.
TECHNICAL DATA
Plug-in power unit operating voltage:
230V/50Hz
Operating voltage, clock: 12 V
JUMBO LED WALL CLOCK
Model AH-1081