Before you start Thank you for purchasing your Aston shower door. We hope it will provide you with years of satisfying use and enjoyment. Please read this manual carefully because it contains information and instructions about the proper installation of the unit. If you do not follow certain conditions of installation and maintenance, your warranty may be affected. 1. Inspect boxes for shipping damage.
Installation Guide Please read and follow the installation instructions and guidelines in this section. Failure to follow the recommended instructions and installation techniques may lead to possible damage to the unit or the surrounding area. This can affect warranty claims. ATTENTION: This unit requires assembly. A minimum of two people are required for assembly, as several of the sections can be large and unstable until assembled.
Detailed Diagram of Shower Door Components RSN Door Panel 1pc | 09 | Wall Anchor Spc 02 | Handle 1pc X40 Screw PCs 03 | Wall Anchor PCs | 11 | Horizontal U-channel PCs Screw PCs Seal (Fixed Panel) PCs 05 | Hinge PCs | 13 | Fixed Panel Shims 3pc 06 | H Seal (3 sections to cut) 1pc | 14 | Vertical channel 1pc 07 | Bottom Seal 1pc | 15 | U-channel Seal 1pc 08 | Fixed Panel 1pc | 16 | U-shaped strip seal (Glass door) | 1pC
Door Panel Assembly and Installation ATTENTION: A minimum of two people are required for the following assembly steps. 1. Attach the Hinges (05) to Door Panel (01). The smooth flat surface of Hinge (05) should be installed on outside of glass door. See Figure 1 for details. NOTE: Never set your glass down directly onto a tile or concrete floor.
3. Hold the Door Panel in place and mark the drill holes for both Hinges (05) on the wall. Set the Door Panel aside and drill the holes in the wall using drill bit. Install the Wall Anchors (03) into the drilled hole. If the walls are reinforced with solid wood blocks,drill pilot holes and then Position the Door Panel (01) back on a protective surface and attach both Hinges to the wall using M5X60 Screws (04). Note: Smooth flat surface of Hinge (05) should be installed on outside of the Door Panel.
4. Locate the H Seal (06), measure and cut lengths to proper sizes. e Install the first section of H Seal to the top edge of Door Panel to the edge of the top Hinge. e Install the second section of H Seal to the edge of Door Panel between the upper Hinge and lower Hinge. e Install the final piece of H Seal to the edge of Door Panel below the lower Hinge. After installation the H Seal should be 1/16" above shower base threshold. See Figure 4 for details. 5.
6. Install the Handle (02) to the Door Panel (01) using the hardware provided. See Figure 6. Inside 7. Measure the width of the Fixed Panel. Note this is dimension "X". The following equation is used to determine the length to be cut from the Horizontal Y See Figure 7 for details.
8. Position the hinged Door Panel so that is perpendicular to the wall and parallel to the threshold. Measure across the bottom span of the shower door and threshold on the outside of shower and determine an equal value. Mark a line on the threshold base (handle side). See Figure 8 for details. e Y 9.Insert the Fixed Panel(8) into the Vertical and Horizontal ¥ f See Figure 9 for details. Y cross section || vertical U-channel Y Horizontal U-channel Figure 9 10.
11. Mark the position of the Horizontal o U-channel (11) on shower base. Mark inside the position of Vertical on W shower wall. See Figure 11 for details. inside Figure 11 12. Carefully place the Fixed Panel aside. NOTE: Never set your glass down directly onto a tile or concrete floor. Always use a piece of foam, cardboard or wood to protect the bottom edge and the l corners of the glass from breaking. / Position the Vertical U-channel (14) with \ marked line on shower wall and mark the hole locations for a
13 Using the appropriate drill bit for your wall surface drill each hole location with a 5/16” diameter drill bit. Using the appropriate drill bit for your floor surface drill hole location with a 5/16" diameter drill bit. See Figure 13 for details. NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size. 14.
16. Put Fixed Panel Shims (13) into the Horizontal See Figure 16 for details. 17. After ensuring the Fixed Panel is set properly check for level and plumb and then apply a small neat bead of 100% clear silicone to the inside bottom of the Vertical and Horizontal U-channels. See Figure 17 for details. 18. Slide Fixed Panel(8) into the Horizontal and Vertical U-channel (14). See Figure 18 for details.
19. Adjust the Fixed Panel (8) position so the gap between Door Panel (01) S and Fixed Panel (8) is between, Optional: If the gap is larger than 1/2" 1 n__1/n add the U-shaped strip to vertical edge (/16 glass door (01). ; Figure 19 Optional 20. Install U-channel Gasket (15) to Fixed N J7 / Panel (8). outside See Figure 20 for details. N\ outside Figure 20 21. Cut the Bottom Seal (12) to the proper length. Install H Seal (12) to Fixed Panel(8). See Figure 21 for details.
Figure 22 22. Apply silicone sealant to the inside and outside edges of Vertical U-channel (14) and Horizontal U-channel (11). See Figure 22 for details.
Care and Maintenance As with any other luxury item, maintenance and care are critical to the long lasting quality and enjoyment of your shower door and tray. The proper care and maintenance outlined in this section are necessary to ensure the longevity of the unit. Damage caused by not following the care and maintenance guidelines in this section is not covered under the manufacturer's warranty.
ASTON GLOBAL INC. — Limited Warranty This warranty applies to products purchased from Aston Global Inc. after May 1, 2017. Aston Global Inc., a Texas Corporation ("Aston"), provides the following warranty coverage for shower doors and enclosures, bathtubs, shower panels and related components (The Products).
PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects. LABOR CHARGES AND/OR DAMAGE INCURRED DURING INSTALLATION, REPAIR, OR REPLACEMENT, AS WELL AS ANY OTHER KIND OF ANCILLARY COST, LOSS OR DAMAGE ARE EXCLUDED. COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial, commercial and business usage.
Aston product installations and repairs must be performed by either an Aston authorized agent or a licensed, insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty.
RESIDENTIAL INSTALLATIONS SHOWER DOORS and ENCLOSURES GLASS: Limited Lifetime Aston warrants the glass of shower doors, tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for the life of the product. Star Cast Protective Coating by Windshield: Ten (10) Years, provided by PCT Global LLC. For shower doors treated with Star Cast protective coating, warranty coverage is provided by its maker, PCT Global LLC.
DRAIN, OVERFLOW AND ACCESSORIES: Limited Lifetime Aston warrants the freestanding tub Drain, Overflow and Accessories in Polished Chrome and Brushed Stainless Steel finishes to be free from defects in workmanship and materials under normal residential use for two (2) years. The warranty for any part in Oil-rubbed Bronze finish shall be limited to one (1) year.
HARDWARE: One (1) Year Aston warrants shower door, tub door and shower enclosure hardware (i.e. handles, rollers, hinges, profiles, clips, guides, brackets, towel and support bars) to be free from defects in workmanship and materials under normal commercial use for one (1) year. SHOWER BASES: One (1) Year Aston warrants shower bases to be free from defects in workmanship and materials under normal commercial use for one (1) year.
SHOWER PANELS: One (1) Year Aston warrants shower panels to be free from defects in workmanship and materials under normal commercial use for a period of one (1) year from the initial date of purchase. STEAM SHOWERS: One (1) Year Aston warrants steam showers panels to be free from defects in workmanship and materials under normal commercial use for a period of one (1) year from the initial date of purchase.
ASTON SCARE THE EVERYDAY Customer Service 877-424-9699 Aston Global Inc 2805 Market Street, Suite 187 Garland, TX. 75041 If further assistance is needed, or you have a question, please visit our web site at: www.astonbath.
