ANTON e A 2 SCARE THE EVERYDAY INSTALLATION AND OWNER'S MANUAL Shower Door Model Number: Please carefully read these instructions before you begin to install the products.
Before you start Thank you for purchasing your Aston shower door. We hope that it will provide you with years of satisfying use and enjoyment. Please read this manual carefully because it contains information and instructions about the proper installation of the unit. If you do not follow certain conditions of installation and maintenance, your warranty may be affected. 1. Inspect boxes for shipping damage.
Detailed Diagram of Shower Door Components Subbed :,T/ ~3 ~ Key Key Number Description QTY Number Description QTY 1 Door Stopper 2 11 Door Threshold 1 2 Top Rail 1 12 Door Threshold End Cap 2 3 Fixed Glass 1 13 Door Seal 1 4 Sliding Door 1 14 Door Seal 1 5 Rail End 2 15 Door Seal 1 6 Wall Mount 2 16 Door Handle 1 7 Vertical channel 1 17 Screw Pack 1 1 8 Sliding Door Track Divider 1 18 Screw Pack 2 1 9 Roller Assembly 4 19 Screw Pack 3 1 10 Fixed Glass Bolt Assembly 2 20 U-channel Seal 1 PLEASE NOTE: During
SUPPLIED HARDWARE r M5x40 D 2 ) Md4x40 Dent 3 Anchor 5 SCREW PACK M4x40 D> 2 (2) Anchor 2 SCREW PACK M4x40 phenol 2 \_ (3) Anchor T 2 SUPPLIED PARTS Model A 48" 52" 56" 60" 64" 68"
Installation Guide Please read and follow the installation instructions and guidelines in this section. Failure to follow the recommended instructions and installation techniques may lead to possible damage to the unit or the surrounding area. This can affect warranty claims. ATTENTION: This unit requires assembly. A minimum of two people are required for assembly, as several of the sections can be large and unstable until assembled.
Reverse Door opening This shower door can be assembled so that the sliding door opens from Left to Right, or Right to Left. The drawings below illustrate the shower door opening from Left to Right. Note the location of the fixed glass panel for the shower door opening from Left to Right. Fixed glass Sliding Door If you wish to install the door opens from Right to Left. Flip the top rail installation so that the Fixed Glass (3) is on the left when installed.
Shower Door Installation Ol S NAAN N 1. Measure the width of the shower opening at the top between the 2 walls. Note this is dimension "X". The following equation is used to determine the length to be cut from the rail in order to fit the shower opening. 2. Measure distance "Y" from the end of the Top Rail (2) with mounting holes and mark the rail. 3. Using a Hack saw or Jig saw cut the Top Rail (2) at the mark. Carefully remove any burrs or sharp edges remaining on Top Rail (2) after the cutting.
)’A\ M4x40 NOTE: Please check with a level and be sure that the Vertical channel is absolutely plumb. 1. Mark the potion on the wall channel. 2.Using the appropriate drill bit for your wall surface drill each hole location with a 5/16" diameter drill bit. Install the plastic Wall Anchors provided into the drilled holes on wall surface. 3. Install the Vertical channel(7) to the wall using M4x40 Screws.
Mark the Top Rail Location ATTENTION: A minimum of two people are required for the next assembly steps. Pr-assembly the top rail (2) onto the fixed glass (3) to locate the mounting points on the wall to your desired location. Painters tape or masking tape in the general location of the of the final installation will aid in marking the wall and floor. N \
Slide door stopper (1) onto end of top rail (2) See figure 1. The bumpers on door stopper (1) should be positioned on the top of top rail for final installation. Note: One door stopper comes per-assembled on top rail between fixed glass bolt assembly. See figure 1. Position the top rail (2) and fixed glass (3) as shown in figure 2 and connect fixed glass (3) to top rail (2) following the assembly sequence shown in figure 2.
Top Rail Assembly To Shower The set screw 5 locations in rail end The set screw 3 are not centered. cations in rail end Assemble per are not centered drawing. Assemble per drawing. N \ G:fl%: Loosen set screws in both rail ends (5) and remove from top rail (2). See figure 1-1. Next remove wall mounts (6) from both rail ends (6). Position wall mounts (6) onto marked location on shower wall and mark pilot hole drilling location. See figure 1-2.
Using the appropriate drill bit for your wall surface drill the hole locations with a 5/16" diameter drill bit. Install the plastic anchors provided into the drilled holes. Repeat for the other side. See figure 2 Attach wall mounts (6) to wall using M5 x 40 screws from Screw Pack 2. Repeat the installation of wall mounts for other side. See figure 3. . Set properly check for level and plumb and then apply a small neat bead of 100% clear silicone to the inside bottom of the Vertical . See figure 4.
Install Wheel Rollers onto the Door Assemble the upper roller assemblies (8) onto sliding door (4) as seen in figure Note: The door handle mounting holes should be positioned to left. The upper roller assemblies (9) will be on the outside of sliding door (4). The sliding door should be to the inside of shower area.
Hanging the Door ROLLER CAM ADJUSTMENT Rotate the outer edge of roller assembly using the small hex, while holding the large hex wrench in place. End View i 1 upper roller assembly Q top rail (2) bottom roller assembly Va or Suspend the sliding door (4) on the top rail (2). Slide the bottom edge of sliding glass door (4) into the groove of the sliding door track divider (8).
Install the Door Threshold The Door Threshold is used to prevent water from seeping out while bathing. Install the threshold according to these instructions. 1. Measure the distance between the fixed glass (3) and the shower wall. See figure 1 2. Using a hacksaw cut the threshold bar (11) to fit distance measured between the fixed glass and shower wall. Remove any sharp edges or burrs after cutting threshold bar (11). See figure 2 3.
NOTE: If your surface is prone to cracking or chipping then it is recommended that you pilot drill first using a smaller drill bit, and then step up to the final size. 4. Using the appropriate drill bit for your tray surface drill the hole locations with a diameter drill bit. Repeat for the other side. See figure 4. 5. Add a small amount of silicone sealant to bottom of threshold bar assembly place into position. See figure 5. 6. Using the hardware from screw pack 3 install the threshold bar assembly.
Installing the door handle Inside Outside i ~ Install the door handle (16) using hardware provided. Follow the assembly sequence seen in drawing.
Final sealing \i\' ~ Using Bath & Kitchen silicone sealant, seal the fixed glass (3) along bottom edge on shower base, and side edge along shower wall. Next seal around sliding door track divider (8).
Care and Maintenance As with any other luxury item, maintenance and care are critical to the long lasting quality and enjoyment of your shower door and tray. The proper care and maintenance outlined in this section are necessary to ensure the longevity of the unit. Damage caused by not following the care and maintenance guidelines in this section is not covered under the manufacturer's warranty.
ASTON GLOBAL INC. — Limited Warranty This warranty applies to products purchased from Aston Global Inc. after May 1, 2017. Aston Global Inc., a Texas Corporation ("Aston"), provides the following warranty coverage for shower doors and enclosures, bathtubs, shower panels and related components (The Products).
PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects. LABOR CHARGES AND/OR DAMAGE INCURRED DURING INSTALLATION, REPAIR, OR REPLACEMENT, AS WELL AS ANY OTHER KIND OF ANCILLARY COST, LOSS OR DAMAGE ARE EXCLUDED. COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial, commercial and business usage.
Aston product installations and repairs must be performed by either an Aston authorized agent or a licensed, insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty.
RESIDENTIAL INSTALLATIONS SHOWER DOORS and ENCLOSURES GLASS: Limited Lifetime Aston warrants the glass of shower doors, tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for the life of the product. Star Cast Protective Coating by Windshield: Ten (10) Years, provided by PCT Global LLC. For shower doors treated with Star Cast protective coating, warranty coverage is provided by its maker, PCT Global LLC.
DRAIN, OVERFLOW AND ACCESSORIES: Limited Lifetime Aston warrants the freestanding tub Drain, Overflow and Accessories in Polished Chrome and Brushed Stainless Steel finishes to be free from defects in workmanship and materials under normal residential use for two (2) years. The warranty for any part in Oil-rubbed Bronze finish shall be limited to one (1) year.
HARDWARE: One (1) Year Aston warrants shower door, tub door and shower enclosure hardware (i.e. handles, rollers, hinges, profiles, clips, guides, brackets, towel and support bars) to be free from defects in workmanship and materials under normal commercial use for one (1) year. SHOWER BASES: One (1) Year Aston warrants shower bases to be free from defects in workmanship and materials under normal commercial use for one (1) year.
SHOWER PANELS: One (1) Year Aston warrants shower panels to be free from defects in workmanship and materials under normal commercial use for a period of one (1) year from the initial date of purchase. STEAM SHOWERS: One (1) Year Aston warrants steam showers panels to be free from defects in workmanship and materials under normal commercial use for a period of one (1) year from the initial date of purchase.
ASTON SCARE THE EVERYDAY Customer Service 877-424-9699 Aston Global Inc 2805 Market Street, Suite 187 Garland, TX. 75041 If further assistance is needed, or you have a question, please visit our web site at: www.astonbath.